NOUVOLED PLANO 300 TW User manual

PLANO 300 TW/CW
LED Fresnel spot light
USER MANUAL
Important note: to use lamps correctly, please read all the terms of this
instruction. Please keep the instruction book in case you need it.

1.1 the crates
Thank you for using this company's products, please read this instruction manual
carefully and carefully and keep it for reference. This specification contains important
information about the installation and use of large power LED lights. Please follow
these instructions carefully when installing and using.
When receiving the product, please check that the product is damaged by shipment.
1.2 Product introduction
This 300W LED SPOT LIGHT, which is made from cast-aluminum, efficient and efficient,
and is suitable for indoor use.
Products strictly according to CE standard design production, in line with the
international standard DMX512 protocol, as well as a single control, also can use
spreading into each other, suitable for large-scale theatrical performances, theaters,
studios, and other places to use.
1.3 Product Features
1.3.1 has the function of smooth adjustment, no flicker, no flicker of the dimmer
process, the adjustment speed can be adjusted by push rod.
1.3.2 The built-in temperature sensor automatically adjusts the light amount
according to the temperature to prevent the lamp from overheating.
1.3.3 has power and DMX512 signal light, which can be monitored at work condition.
1.3.4 digital tube pure digital display.
1.3.5 The buttons and the digital tube display can be inverted.
1.3.6 Both the power line and the signal line are connected by hand.
1.3.7 Uses a reflective cup to project a uniform flare.
Product general performance:
* Adjust 0 to 100%
* Stroboscopic
* self-walking program

* The protection level IP25
1.4 specifications
1.5 Technical parameters:
External working voltage: AC100-240V, 50/60HZ,
Maximum power: 350W
Beam Angle: 15-50 degrees
The number of colors of various colors: 1
Using the environment temperature range: 15 ℃and 40 ℃
1.6 Safety Warning
Important note:
The manufacturer will not be responsible for any accidents and losses caused by any
unauthorized use and unauthorized alteration of the equipment.
Special attention should be paid to the voltage of the power supply to ensure that the
voltage range is within the voltage range of the technical parameter marker
(100V-240V). Due to many rural areas of voltage fluctuation range is too big, be sure
to connect a power supply voltage regulator, and then connect the lamps and
lanterns, the lamps and lanterns may be burned or make lamps and lanterns can't
work.
Pieces do not use other electrical power cord and the lamp power supply
input/output connector line together, also do not put other appliances DMX512
signal with this light DMX512 signal input/output connector lines connected together.
To ensure the safety of the power supply, please use the quality electrical outlet or
cut the plug directly.
It is not recommended to use this lamp in direct sun exposure to avoid overheating
during work.
2.1 device
If the lamp is used as a lamp or top light, please put the lamp on the hanging arm of
the lamp, screw tight. Then hang the lights on the truss. Adjust the position Angle of

the light beam azimuth, and tighten the handle screw. If the lamp as a row of lights or
footlights to use, as long as the two-hanging arm off a certain angle, sit here as a
scaffold, and then adjust the lamps and lanterns and the angle between the hanging
arm, use light meets the requirements of elevation, then tighten the handle screw.
2.2 The Power Connection
This product uses the input output power line of 1.5 square mm copper core wire,
plug is 2 core 10A pair. When the power cord is in series, no more than 16 lights will
be used when using 220V ac power.
Use this product DMX512 signal input and output don't more than 16 lamp, street
line connection in DMX controller with light or light with the light signal lines, more
than 100 meters, must increase the level of signal amplifier.
Project distribution installation
In adopting the company lamps and lanterns, if adopt the three-phase five-wire
system, the zero line should be on each phase
This is the uniform output from the box, not a single zero.
3Operating method
3.1 Display and key operation part:
Operational instructions: Under the main menu, press the up and down keys
to select different function menus, select different function menus, then
press the confirmation key to enter the corresponding pull-down menu
functions, and press the increase or decrease key in the pull-down menu to
modify its parameter values. Press the confirmation key to return to the main
menu.
3.2 Function
NO
display
Explain
1
DMX-Addr
001
Under the current main menu, press the
confirmation key to enter the adjustment
state, press the upper and lower keys to
adjust the address code, then press the

confirmation key to save and exit the
adjustment state.
2
Rotary
-ADJ
0－255
Under the current main menu, press the
confirmation key to enter the drop-down
menu, and adjust the dimming knob to
adjust the brightness of the light. Press the
menu key to return to the upper menu.
3
Key-A
DJ
0－255
Under the current main menu, press the
confirmation key to enter the drop-down
menu, and press the up and down keys to
adjust the brightness of the lights. Press the
menu key to return to the upper menu.
4
Focus-
ADJ
0－255
Under the current main menu, press the
confirmation button to enter the drop-down
menu, and press the upper and lower keys to
adjust the focus of the light. Press the
confirmation key to save and exit the
adjustment state.
5
Screen
Rotate
ON/OFF
Press the confirmation key under the current
main menu, press the confirmation key to
enter the drop-down menu, press the up and
down keys to adjust the brightness of the
light. Press the menu key to return to the
upper menu. Enter the selection state, press
the upper and lower keys to select,
determine the key to save and exit, press the
menu key to return to the upper menu.
3.3 Background display window description
NO
display
1
WW-SELECT
0－255
2
RT-SELECT
0－255
3
Fan temp
20－70
4
Low power temp
35－90
5
Protect temp
ON/OFF

6
CW-GLO
20－255
7
WW-GLO
20－255
8
Focal stroke
0－255
9
Focal speed
0－100
10
Language
EN
11
Screen saver
ON/OFF
3.4 DMX512 Channel Description
NO
Function
Description
Channel 1
Dimming
Total dimming, linear
dimming, from dark to light
Channel 2
Strobe
Total strobe, from slow to fast
Channel 3
Warm white dimming
Warm white dimming, linear
dimming, from dark to bright
Channel 4
Warm white dimming
Warm white dimming, linear
dimming, from dark to bright
Channel 5
focus
4．RDM Description:
NO
Function
Description
1
Feedback (Address
Code)
Free to change
2
Feedback
(Equipment
Temperature)
Unmodifiable
After power-on, turn on the console power supply. When the signal of
DMX512 console is not received, the DMX indicator does not turn on. When
the signal of DMX512 console is received, the DMX indicator lights up,
which is controlled by the console signal.
In the address code state, if there is no console after multi-computer
connection, the master-slave online function can be realized. One of the
devices can be operated. The other devices in the address state run
synchronously with the host. When the master-slave online, the DMX512
signal must be cut off.