Allows usage of higher voltage receiver battery packs (6-8
cell Ni-Cd or Ni-MH, or 2 cell Li-Po packs) and regulates output
voltage to the radio system, to provide strong/consistent
servo performance throughout the duration of your run.
TO INSTALL SERVO BOOSTER:
1. Connect the Servo Booster’s RED 20 gauge silicone wire (larger
wire with no connectors) to Positive (+) of the receiver battery
pack.
2. Connect the Servo Booster’s BLACK 20 gauge silicone wire to
Negative (–) of the receiver battery pack.
3. Plug the Servo Booster’s black 3-pin receiver harness into the
battery slot (or other unused channel) of the receiver.
The Servo Booster’s receiver harness is wired for new style receivers. If you have
older style KO or older black cased Airtronics receivers, you may need to change
the wiring sequence of the harness to avoid possible receiver damage.
4. Mount the Servo Booster’s main module to the vehicle’s
chassis using the included double-sided mounting tape.
5. Mount the Servo Booster’s ON/OFF switch in a convenient place
in the car using a screw or the included double-sided tape.
NOTE: The Servo Booster’s ON/OFF switch will be the only power
switch you will need to turn the radio system on and off.
PRODUCT WARRANTY: Novak Electronics, Inc. guarantees all products to be free from
defects in materials or workmanship for a period of 120 days from the original date of
purchase (verified by dated, itemized sales receipt). In no case shall our liability exceed
www.teamnovak.
#5460 Nitro Servo
Regulator
(w/B.E.C. Regulator)
IN-5460-1 • 10/2004
Allows usage of higher voltage receiver battery packs (6-8
cell Ni-Cd or Ni-MH, or 2 cell Li-Po packs) and regulates output
voltage to the radio system, to provide strong/consistent
servo performance throughout the duration of your run.
TO INSTALL SERVO BOOSTER:
1. Connect the Servo Booster’s RED 20 gauge silicone wire (larger
wire with no connectors) to Positive (+) of the receiver battery
pack.
2. Connect the Servo Booster’s BLACK 20 gauge silicone wire to
Negative (–) of the receiver battery pack.
3. Plug the Servo Booster’s black 3-pin receiver harness into the
battery slot (or other unused channel) of the receiver.
The Servo Booster’s receiver harness is wired for new style receivers. If you have
older style KO or older black cased Airtronics receivers, you may need to change
the wiring sequence of the harness to avoid possible receiver damage.
4. Mount the Servo Booster’s main module to the vehicle’s
chassis using the included double-sided mounting tape.
5. Mount the Servo Booster’s ON/OFF switch in a convenient place
in the car using a screw or the included double-sided tape.
NOTE: The Servo Booster’s ON/OFF switch will be the only power
switch you will need to turn the radio system on and off.
PRODUCT WARRANTY: Novak Electronics, Inc. guarantees all products to be free from
defects in materials or workmanship for a period of 120 days from the original date of
purchase (verified by dated, itemized sales receipt). In no case shall our liability exceed
www.teamnovak.
#5460 Nitro Servo
Regulator
(w/B.E.C. Regulator)
IN-5460-1 • 10/2004
Allows usage of higher voltage receiver battery packs (6-8
cell Ni-Cd or Ni-MH, or 2 cell Li-Po packs) and regulates output
voltage to the radio system, to provide strong/consistent
servo performance throughout the duration of your run.
TO INSTALL SERVO BOOSTER:
1. Connect the Servo Booster’s RED 20 gauge silicone wire (larger
wire with no connectors) to Positive (+) of the receiver battery
pack.
2. Connect the Servo Booster’s BLACK 20 gauge silicone wire to
Negative (–) of the receiver battery pack.
3. Plug the Servo Booster’s black 3-pin receiver harness into the
battery slot (or other unused channel) of the receiver.
The Servo Booster’s receiver harness is wired for new style receivers. If you have
older style KO or older black cased Airtronics receivers, you may need to change
the wiring sequence of the harness to avoid possible receiver damage.
4. Mount the Servo Booster’s main module to the vehicle’s
chassis using the included double-sided mounting tape.
5. Mount the Servo Booster’s ON/OFF switch in a convenient place
in the car using a screw or the included double-sided tape.
NOTE: The Servo Booster’s ON/OFF switch will be the only power
switch you will need to turn the radio system on and off.
PRODUCT WARRANTY: Novak Electronics, Inc. guarantees all products to be free from
defects in materials or workmanship for a period of 120 days from the original date of
purchase (verified by dated, itemized sales receipt). In no case shall our liability exceed
www.teamnovak.
#5460 Nitro Servo
Regulator
(w/B.E.C. Regulator)
IN-5460-1 • 10/2004
Allows usage of higher voltage receiver battery packs (6-8
cell Ni-Cd or Ni-MH, or 2 cell Li-Po packs) and regulates output
voltage to the radio system, to provide strong/consistent
servo performance throughout the duration of your run.
TO INSTALL SERVO BOOSTER:
1. Connect the Servo Booster’s RED 20 gauge silicone wire (larger
wire with no connectors) to Positive (+) of the receiver battery
pack.
2. Connect the Servo Booster’s BLACK 20 gauge silicone wire to
Negative (–) of the receiver battery pack.
3. Plug the Servo Booster’s black 3-pin receiver harness into the
battery slot (or other unused channel) of the receiver.
The Servo Booster’s receiver harness is wired for new style receivers. If you have
older style KO or older black cased Airtronics receivers, you may need to change
the wiring sequence of the harness to avoid possible receiver damage.
4. Mount the Servo Booster’s main module to the vehicle’s
chassis using the included double-sided mounting tape.
5. Mount the Servo Booster’s ON/OFF switch in a convenient place
in the car using a screw or the included double-sided tape.
NOTE: The Servo Booster’s ON/OFF switch will be the only power
switch you will need to turn the radio system on and off.
PRODUCT WARRANTY: Novak Electronics, Inc. guarantees all products to be free from
defects in materials or workmanship for a period of 120 days from the original date of
purchase (verified by dated, itemized sales receipt). In no case shall our liability exceed
www.teamnovak.
#5460 Nitro Servo
Regulator
(w/B.E.C. Regulator)
IN-5460-1 • 10/2004
Allows usage of higher voltage receiver battery packs (6-8
cell Ni-Cd or Ni-MH, or 2 cell Li-Po packs) and regulates output
voltage to the radio system, to provide strong/consistent
servo performance throughout the duration of your run.
TO INSTALL SERVO BOOSTER:
1. Connect the Servo Booster’s RED 20 gauge silicone wire (larger
wire with no connectors) to Positive (+) of the receiver battery
pack.
2. Connect the Servo Booster’s BLACK 20 gauge silicone wire to
Negative (–) of the receiver battery pack.
3. Plug the Servo Booster’s black 3-pin receiver harness into the
battery slot (or other unused channel) of the receiver.
The Servo Booster’s receiver harness is wired for new style receivers. If you have
older style KO or older black cased Airtronics receivers, you may need to change
the wiring sequence of the harness to avoid possible receiver damage.
4. Mount the Servo Booster’s main module to the vehicle’s
chassis using the included double-sided mounting tape.
5. Mount the Servo Booster’s ON/OFF switch in a convenient place
in the car using a screw or the included double-sided tape.
NOTE: The Servo Booster’s ON/OFF switch will be the only power
switch you will need to turn the radio system on and off.
PRODUCT WARRANTY: Novak Electronics, Inc. guarantees all products to be free from
defects in materials or workmanship for a period of 120 days from the original date of
purchase (verified by dated, itemized sales receipt). In no case shall our liability exceed
www.teamnovak.
#5460 Nitro Servo
Regulator
(w/B.E.C. Regulator)
IN-5460-1 • 10/2004
Allows usage of higher voltage receiver battery packs (6-8
cell Ni-Cd or Ni-MH, or 2 cell Li-Po packs) and regulates output
voltage to the radio system, to provide strong/consistent
servo performance throughout the duration of your run.
TO INSTALL SERVO BOOSTER:
1. Connect the Servo Booster’s RED 20 gauge silicone wire (larger
wire with no connectors) to Positive (+) of the receiver battery
pack.
2. Connect the Servo Booster’s BLACK 20 gauge silicone wire to
Negative (–) of the receiver battery pack.
3. Plug the Servo Booster’s black 3-pin receiver harness into the
battery slot (or other unused channel) of the receiver.
The Servo Booster’s receiver harness is wired for new style receivers. If you have
older style KO or older black cased Airtronics receivers, you may need to change
the wiring sequence of the harness to avoid possible receiver damage.
4. Mount the Servo Booster’s main module to the vehicle’s
chassis using the included double-sided mounting tape.
5. Mount the Servo Booster’s ON/OFF switch in a convenient place
in the car using a screw or the included double-sided tape.
NOTE: The Servo Booster’s ON/OFF switch will be the only power
switch you will need to turn the radio system on and off.
PRODUCT WARRANTY: Novak Electronics, Inc. guarantees all products to be free from
defects in materials or workmanship for a period of 120 days from the original date of
purchase (verified by dated, itemized sales receipt). In no case shall our liability exceed
www.teamnovak.
#5460 Nitro Servo
Regulator
(w/B.E.C. Regulator)
IN-5460-1 • 10/2004
