NRS Healthcare S13909 User manual

1
USER INSTRUCTIONS
EASYLIFT HOME - HEIGHT ADJUSTABLE
TILTING OVER-BED TABLE
S13909 Height Adjustable Tilting Over-Bed Table
2. SAFETY
WARNING: The central column is spring loaded.
Make sure the central column hand-wheel is in
position & fully tightened before assembly/
disassembly of the table.
WARNING: Do not exceed the safe working load of
25kg (4st).
WARNING: Do not exceed the safe working load of the
storage tray 1kg.
ALWAYS make sure that the table is correctly
positioned and adjusted to allow it to be used safely and
comfortably.
DO NOT lean or sit on the table.
DO NOT place hot objects directly on the table surface.
Maximum heat resistance 65°C (149°F).
MAKE SURE the area is clear before moving the table.
MAKE SURE the tabletop is clear before tilting the
angle.
TAKE CARE when moving the table over rough or
uneven surfaces. Lift the table over large ridges and
wide gaps.
ENTRAPMENT HAZARD: Do not use this product
within 318 mm of headboard or other similar object.
ENTRAPMENT HAZARD: Take care of fingers when
opening and closing the tabletops.
ENTRAPMENT HAZARD: Always move the table to a
safe location when the user is sleeping.
3. UNPACKING
Remove the packaging and check all parts carefully.
Contact your supplier immediately if parts are missing or
damaged and do not try and assemble.
3.1 Contents:
7
8
10
11
9
5
6
4
1
2
3
1. Table Top Assembly x 1
2. Column Assembly & Inner Rod x 1
Note: Do not remove the PVC anti-rattle sleeves
from either end of the inner rod.
3. Central Column Hand-wheel x 1
4. Storage Tray x 1
5. Base Assembly x 1
6. Mushroom Feet x 4
7. M8 x 20mm Socket-Head Button-Screws x 4
8. M8 x 40mm Socket-Head Button-Screws x 4
9. Castors x 4
10. Allen Key x 1
11. Castor Spanner x 1
General Safety Warning
Please make sure that you read and follow these
instructions carefully. Keep these instructions in a
safe place for future reference.
Safe Working Load
4st
25kg
1. INTENDED USE
The Easylift Home Over-Bed Table has been designed to provides users with a firm, flat / tilting surface that is suitable
for eating, writing, reading etc. The height can be easily adjusted from 710mm to 1090mm, and the main tabletop can
be tilted from 0° to 40° degrees. The single column construction and adjustable height makes this product suitable for
use with most divan beds, slatted beds, and height adjustable medical beds. A discrete storage tray has been cleverly
hidden under the folding side table.

2
4. ASSEMBLY
Note: We recommend a 2 person assembly.
Note: The main tabletop has been pre-installed for a
right-hand side use. If you wish to use the over-bed
table on the left-hand side of the bed, you will need to
change the main table-top orientation before assembly.
4.1 Change the Tabletop Orientation
Warning: Secure the tabletop before performing
this operation. The tabletop can swing open
causing injury to the user or damage to the tilt
mechanism.
4.1.1 Remove Tabletop
Use the supplied Allen key to remove the 3 x M6 x
20mm screws to release the tabletop from the frame
assembly.
4.2 Refit the Tabletop on the Opposite Side
1. Rotate the frame 180 degrees.
2. Re-secure the tabletop to the frame assembly using
the Allen key to reinstall the 3 x M6 x 20mm screws.
Note: Make sure the screws are fully tight before you do
the next step.
4.3 Fit the Central Column Hand-wheel
Insert the hand-wheel and turn clockwise to tighten.
4.4 Assemble the Tabletop & Central Column
B
B
1. Slide the inner rod (B) into the central column.
Note: Make sure the flanged end is facing the correct
way up. The plastic anti-rattle cover is marked ‘UP’.
A
B
2. Guide the flanged end of the inner rod (B) into the
height adjustment lever hole in the main frame.
Note: Make sure the label on the central column is
facing inwards before assembly.

3
3. Secure the column assembly to the table top
assembly using the 4 x M8 x 20mm socket head
screws and the Allen key provided.
4. Make sure that all four screws are fully tight before
you continue the assembly.
4.5 Assemble the Base to the Central Column
Note: Make sure that the base faces the same direction
as the table top and the castor inserts face upwards (as
shown).
1. Secure the base assembly to the column assembly
using the 4 x M8 x 40mm socket head screws and
the Allen Key provided.
2. Make sure that all four screws are fully tight before
you continue the assembly.
4.6 Fitting the Castors / Feet
4.6.1 Fitting the Castors
1. Insert the screw thread into the threaded insert,
hold the castor and turn the nut by hand until the
threads engage.
2. Tighten the castor threads using the 14mm spanner
provided.
3. To remove the castors reverse step 1 & 2.
4.6.2 Fitting the mushroom feet
The mushroom feet should be fitted for use with a low
base divan.
Press-fit the mushroom feet into the castor insert holes.
4.7 Fitting the Storage Tray
1. Open the side and main table (refer to Section 5.2).
2. Slot the storage tray over the tabs on the table
frame as shown.

4
5. IN USE
5.1 Locking and Unlocking the Brakes.
Note: The table has 4 independently lockable castors.
We recommend that the castor locks are always fully
engaged when the product is in use or stationary.
Fig 1: Castor Unlocked Fig 2: Castor Locked
1. To lock the castor brake, press down on the castor
tab (Fig 1).
2. To disengage the castor brake, flip up the castor
tab (Fig 2).
5.2 Opening & Adjusting the Tabletops
A
B
5.2.1 Open the Side-table.
Note: The side-table has a magnetic lock and requires a
small amount of force to open.
To open, pull the side-table in the direction shown (A).
5.2.2 Adjust the Main Tabletop Angle
Note: The main tabletop can be adjusted to the
following angles 18°, 24°, 30°, 36° & 40° degrees.
1. Pull the main tabletop towards you until you reach
the desired angle (B).
2. Release the tabletop to lock into place.
Warning: Make sure the tabletop has locked into
place before releasing fully.
Note: Pulling the tabletop all the way towards you will
release the ratchet mechanism. If the tabletop does not
lock into position, return the tabletop to the horizontal
position to reset the ratchet mechanism.
5.3 Closing the Tables
C
D
E
5.3.1 Close the Side Table
Lower the side table to the horizontal position (C).
5.3.2 Close the Main Tabletop
1. Pull the main table all the way towards you to
release the ratchet mechanism (D).
2. Gently lower the main tabletop to the horizontal
position (E).
Warning: Do not let the tabletop drop as this will
cause damage to the tilt mechcanism, or cause
injury to the user.
5.4 Raising & Lowering the Table
F
G
1. To release the central column, unscrew the locking
hand-wheel (F) by turning anti-clockwise.

5
2. Pull lever (G) up to release the spring mechanism,
then simultaneously raise or lower the table-top into
position.
3. To lock the central column, screw the locking hand-
wheel (F) clockwise.
6. MAINTENANCE
Regularly check the wheels rotate freely.
Regularly check the tilting ratchet mechanism functions
correctly.
Regularly check the brakes function correctly in
accordance with Section 5.1.
Always check the locking hand-wheel is fully tight before
use.
Make sure the hand-lever is functioning correctly.
7. CLEANING INSTRUCTIONS.
We recommend removing the storage tray before
cleaning.
Please check the suitability of the cleaning products
before use. Do not use abrasive cleaners or cloths
as these could permanently damage the surface and
invalidate any warranty.
Do not use solvents to clean the product.
Make sure that all dirt and debris is removed from
around the wheels.
Make sure that all dirt and debris is removed from the
tilting ratchet mechanism.
Clean regularly using a general purpose, neutral
detergent and warm water.
To disinfect, wipe with a dilute bleach solution, and rinse
thoroughly with fresh water.
Allow product to fully dry prior to use/storage.
8. ACCESSORIES & SPARE PARTS
S20161: Spares Kit
• Replacement Mushroom Feet (set of 4).
• Replacement Castors (set of 4).
For more details please visit our website or call
Customer Services on the details below.
9. PRODUCT DISPOSAL
This product must be thoroughly cleaned/sterilised prior
to disposal.
This product is manufactured from metal, wood &
plastic and can be disposed of through Local Authority
Household Waste and Recycling Centres or through
Local Trade Waste Collectors.
10. PRODUCT GUARANTEE
NRS Healthcare guarantee this product for a period of
12 months, from the date of purchase, against faulty
materials and workmanship.
This guarantee does not cover; abuse, misuse,
interference or tampering with any part of the product.
Any guarantee issued by NRS Healthcare does not
affect your statutory rights.

6S13909-UI-1 01-12-2022
NRS HEALTHCARE Sherwood House, Cartwright Way, Forest Business Park
Bardon Hill, Coalville, Leicestershire, LE67 1UB, UK.
Tel: Customer Services: 0345 121 8111 Email: customerser[email protected].uk
NRS Healthcare is a leading supplier of community equipment and daily living aids.
Please visit one of our websites to view our full range of products:
www.healthcarepro.co.uk or www.completecareshop.co.uk