NRS Healthcare NUVO User manual

1
USER INSTRUCTIONS
NUVO MOBILE SHOWER CHAIR
P64491 NUVO Mobile Shower Chair
General Safety Warning
Please make sure that you read and follow these
instructions carefully. Keep these instructions in
a safe place for future reference.
Maximum User Weight
26st
166kg
1. INTENDED USE
The NUVO Mobile Shower Chair has been designed to be used in a bathroom or shower, to provide stable
seating for users with reduced mobility who are unable to stand during showering. This product is supplied
in parts, some basic assembly is required. The Chair frame has been made from high quality stainless steel
offering superior corrosion resistance.
2. SAFETY
Warning: The maximum user weight must not be
more than 166Kg (26st).
Make sure the seat is securely fitted to the frame.
Do not stand on the chair under any circumstances,
failure to comply can result in serious injury.
Do not sit or rest on the arm rests under any
circumstances, failure to comply can result in
serious injury.
Make sure that all castors are LOCKED before
getting in and out of the shower chair, whilst
showering or if leaving the user for any period of
time.
Inspect the product regularly to make sure it is not
damaged.
Do not use if the castors are damaged.
Plan route before moving to avoid obstacles.
Wipe dry after each use.
1
2
4
5
6
3
3. UNPACKING
Remove the packaging and check all parts carefully.
Contact your supplier immediately if parts are
missing or damaged and do not try and assemble.
3.1 Contents:
1. Base Frame Assembly x 1
2. RH Arm Rest Assembly x 1
3. LH Arm Rest Assembly x 1
4. Castor Leg Assembly x 4
5. Plastic Moulded Seat x 1
6. E-Clips x 9

2
4. ASSEMBLY/INSTALLATION
4.1 Attach the Seat:
Attach the front of the seat to the seat frame assembly
using the front clips first.
Note: Make sure the front seat clips fit inside the
metal spacers on the front crossbar.
Rotate the seat until the rear clips click into place.
4.2 Assemble the LH/RH Arm Rests
Slot the arm rests together as shown.
Secure the arm rests using 1 x E-clip.
4.3 Attach the Arm Rest Assembly to the Seat
Frame
Slot the arm rest assembly onto the seat frame
assembly.
Secure the arm rest assembly using 4 x E-clips.

3
4.4 Attach the Leg/Castor Assemblies
Place the seat frame assembly on its side and attach
the leg/castor assemblies using 2 x E-clips.
Repeat the step for the opposite side.
Note: Make sure that all legs have been adjusted to
the same height.
4.5 Adjusting the seat height
Note: The seat height has an adjustment range from
400mm to 550mm in 25mm increments.
Place the seat frame assembly on its side, remove
the 2 x E-clips and adjust the legs to the required
height.
Secure the legs with the 2 x E-clips.
Repeat for the opposite side.
Note: Make sure that all legs have been adjusted to
the same height.
5. IN USE
Warning: Make sure the castors are locked before
the user lowers or raises from the chair.
5.1 Locking/Unlocking the Castors:
12
1. Push the locking tabs down to lock the castors.
2. Push the release tabs down to unlock the castors.
6. MAINTENANCE
Inspect the product regularly for signs of wear or
damage, pay particular attention to the condition of
the castors and plastic joint spacers.
Any suspected faults or damage must be reported
to the supplier and the product taken out of use
immediately.
Check that all fixing clips and plastic joint spacers
are fitted correctly with no excessive movement.
7. CLEANING INSTRUCTIONS.
Please check the suitability of the cleaning products
before use.
Do not use abrasive cleaners or cloths as these could
permanently damage the surface and invalidate any
warranty.
Clean regularly using a general purpose, neutral
detergent and warm water.
DO NOT use solvents to clean the product.
To disinfect, wipe with a dilute bleach solution, and
rinse thoroughly with fresh water.
Make sure that all dirt and debris is removed from
around the castors.
This product is suitable for thermal decontamination
and can be steam cleaned or autoclaved on cleaning
cycles up to 80°C.

4
8. PRODUCT DISPOSAL
This product must be thoroughly cleaned/sterilised
prior to disposal.
This product is manufactured from metal and plastic
and can be disposed of through Local Authority
Household Waste and Recycling Centres or through
Local Trade Waste Collectors.
9. PRODUCT GUARANTEE
NRS Healthcare guarantee this product for a period
of 12 months, from the date of purchase, against
faulty materials and workmanship.
This guarantee does not cover; fair wear & tear,
abuse, misuse, interference or tampering with any
part of the product.
Any guarantee issued by NRS Healthcare does not
affect your statutory rights.
NRS HEALTHCARE Sherwood House, Cartwright Way, Forest Business Park, Bardon Hill, Coalville,
Leicestershire, LE67 1UB, UK.
Tel. Customer Services: 0345 121 8111
Email: [email protected]
NRS Healthcare is a leading supplier of community equipment and daily living aids, to
view our full range, visit our website:
www.nrshealthcare.co.uk
P64491-UI-1 19-11-2020