Nutricia Flocare 800 How to use

Preparation and start of the pump
Operating instructions
Turning on
the pump
Programming
Continuous Feeding
Programming
Dose Feeding
Changing
Programming
>Turn on the pump by pressing the “POWER/ON” key. The pump is in “HOLD” mode.
>Set the desired flow rate (ml/h) by pressing the “INC” or “DEC” keys.
>Flow rates can be set from 1 to 300 ml/h, in 1 ml increments.
>Press the “RUN” key to start the pump.
>After programming the flow rate do not immediately press the “RUN” key.
>Press the “DOSE” key to set the desired dose.
>Press “INC” or “DEC” to program the correct dose (in ml).
>Press the “RUN” key to start the pump.
>Press “HOLD” key, pump will stop, all memory and programming is retained.
Use this to: change flow rate, alter dose setting, change feed, administer medication.
>Press “RUN” to restart the pump.
Flocare 800
Short Manual
1 2 3 4
>Insert the drip chamber of the feeding set into the drip detector slot of the pump.
>Slowly open the roller clamp on the feeding set and allow the total set to fill with feed. Make sure the drip chamber
is filled up about one-third.
>Stretch the tubing around the pump wheel and insert the plastic retainer into the bracket on the pump.
>Pull the tubing through the tubing guide.
Connect the feeding set to your tube and continue to operate the pump.
1
2
3
4
ENTERAL FEEDING PUMP
RUN
RATE ML/HR
DOSE COMPLETE
OCCLUSION
NO FLOW
LOW BATTERY
MALFUNCTION
AC POWER
HOLD
DOSE
VOL
FED
DEC
INC
ENTERAL FEEDING PUMP
RUN
RATE ML/HR
DOSE COMPLETE
OCCLUSION
NO FLOW
LOW BATTERY
MALFUNCTION
AC POWER
HOLD
DOSE
VOL
FED
DEC
INC
ENTERAL FEEDING PUMP
RUN
RATE ML/HR
DOSE COMPLETE
OCCLUSION
NO FLOW
LOW BATTERY
MALFUNCTION
AC POWER
HOLD
DOSE
VOL
FED
DEC
INC
ENTERAL FEEDING PUMP
RUN
RATE ML/HR
DOSE COMPLETE
OCCLUSION
NO FLOW
LOW BATTERY
MALFUNCTION
AC POWER
HOLD
DOSE
VOL
FED
DEC
INC
ENTERAL FEEDING PUMP
RUN
RATE ML/HR
DOSE COMPLETE
OCCLUSION
NO FLOW
LOW BATTERY
MALFUNCTION
AC POWER
HOLD
DOSE
VOL
FED
DEC
INC
ENTERAL FEEDING PUMP
RUN
RATE ML/HR
DOSE COMPLETE
OCCLUSION
NO FLOW
LOW BATTERY
MALFUNCTION
AC POWER
HOLD
DOSE
VOL
FED
DEC
INC
ENTERAL FEEDING PUMP
RUN
RATE ML/HR
DOSE COMPLETE
OCCLUSION
NO FLOW
LOW BATTERY
MALFUNCTION
AC POWER
HOLD
DOSE
VOL
FED
DEC
INC
ENTERAL FEEDING PUMP
RUN
RATE ML/HR
DOSE COMPLETE
OCCLUSION
NO FLOW
LOW BATTERY
MALFUNCTION
AC POWER
HOLD
DOSE
VOL
FED
DEC
INC
ENTERAL FEEDING PUMP
RUN
RATE ML/HR
DOSE COMPLETE
OCCLUSION
NO FLOW
LOW BATTERY
MALFUNCTION
AC POWER
HOLD
DOSE
VOL
FED
DEC
INC
ENTERAL FEEDING PUMP
RUN
RATE ML/HR
DOSE COMPLETE
OCCLUSION
NO FLOW
LOW BATTERY
MALFUNCTION
AC POWER
HOLD
DOSE
VOL
FED
DEC
INC
Viewing total volume
delivered
Turning off the pump
>Press “VOL FED” key, display will indicate total volume delivered.
>Turn on the pump by pressing the “OFF” key for ca 3 seconds.
ENTERAL FEEDING PUMP
RUN
RATE ML/HR
DOSE COMPLETE
OCCLUSION
NO FLOW
LOW BATTERY
MALFUNCTION
AC POWER
HOLD
DOSE
VOL
FED
DEC
INC
ENTERAL FEEDING PUMP
RUN
RATE ML/HR
DOSE COMPLETE
OCCLUSION
NO FLOW
LOW BATTERY
MALFUNCTION
AC POWER
HOLD
DOSE
VOL
FED
DEC
INC
ENTERAL FEEDING PUMP
RUN
RATE ML/HR
DOSE COMPLETE
OCCLUSION
NO FLOW
LOW BATTERY
MALFUNCTION
AC POWER
HOLD
DOSE
VOL
FED
DEC
INC
800
ENTERAL FEEDING PUMP
RUN
RATE ML/HR
DOSE COMPLETE
OCCLUSION
NO FLOW
LOW BATTERY
MALFUNCTION
AC POWER
HOLD
DOSE
VOL
FED
DEC
INC
800
ENTERAL FEEDING PUMP
RUN
RATE ML/HR
DOSE COMPLETE
OCCLUSION
NO FLOW
LOW BATTERY
MALFUNCTION
AC POWER
HOLD
DOSE
VOL
FED
DEC
INC
800
ENTERAL FEEDING PUMP
RUN
RATE ML/HR
DOSE COMPLETE
OCCLUSION
NO FLOW
LOW BATTERY
MALFUNCTION
AC POWER
HOLD
DOSE
VOL
FED
DEC
INC
800
ENTERAL FEEDING PUMP
RUN
RATE ML/HR
DOSE COMPLETE
OCCLUSION
NO FLOW
LOW BATTERY
MALFUNCTION
AC POWER
HOLD
DOSE
VOL
FED
DEC
INC

171102 / BP&MC 11090802
>The pump has been left in “hold” mode
for 3.5 minutes.
>Reset the alarm by pressing the “HOLD” key, or
>Continue feeding by pressing the “RUN” key.
>The feeding set is incorrectly placed. >Press the “HOLD” key, insert the plastic
retainer into the bracket on the pump, and
then “RUN”.
>The pump has finished administering
the programmed dose.
>Switch the pump off by pressing “OFF” key, or
>Program the pump to administer a repeat dose
by pressing “HOLD” and then “RUN”.
>The feeding container is empty.
>The liquid level in the drip chamber is too
high.
>The sensor area is dirty.
>There is an obstruction to flow,
either in the feeding set or in the tube.
>Change the feeding container or switch off
the pump.
>Remove the set from the pump; hold the set
upside-down so that feed runs back in to the
container, until the chamber is ca. one-third
full. Reload the set.
>Remove the drip chamber from the slot and
clean the drip detector sensors with a damp
cotton swab.
>Check the feeding set, ensure that the roller
clamp is fully opened and that there are no
kinks in the tubing, and/or
>Remove the set from the pump and check if
feed is flowing from top to bottom (with the
roller clamp open), and/or
>Check if your tube is clogged by flushing the
tube.
>Ca. 30 minutes of battery time remain. >Connect the pump to the mains and charge
the pump. During charging the pump can be
used.
>The pump needs repair. >Contact your healthcare practitioner.
HOLD
SET
DOSE COMPLETE
OCCLUSION
NO FLOW
LOW BATTERY
MALFUNCTION
(E-1 to E-11)
Problem/Alarm Likely cause Instructions
Flocare 800
Problem solving
instructions
Error messages and instructions
Please refer to detailed Instructions for Use for additional information