Nutricia Flocare Infinity How to use

FLOCARE INFINITY PUMP
SHORT MANUAL
11
Continuous
feeding
START/STOPSTART/STOP
CLRCLR
ml/hml/h
DOSE=VOLDOSE=VOL
++
400ml/h
––
1ml/h
22
Pre-set
dose
START/STOPSTART/STOP
ml/hml/h
DOSE=VOLDOSE=VOL
++
400ml/h
––
1ml/h
++
4000ml/h
––
1ml/h
Operating instructions
Clearing pump
memory and priming
the feeding set
When switching the pump on or o,
press this key for 2 seconds.
This will clear the previous volume.
The rate and dose will remain unchanged.
Pressing this key for 2 seconds will
automatically fill the feeding set. Connect the
feeding set to the feeding tube and choose
appropriate feeding program
11
or
22
.
CLRCLR
ON/OFFON/OFF
FILL SETFILL SET
INFOINFO
Preparing and setting up the pump
11
Open the pump
door by pressing
gently up on the
lower wall (A) and
rotating the door
upwards (B) at the
same time.
Position the looped
section of the
silicone tubing
around the rotor.
22
Stretch slightly
to seat the
cassette into
the pump.
33
Close the pump door
- you should hear a
small click when it is
closed properly. The
pump is now ready to
be switched on.
44
AT HOME

If your pump alarms:
STEP 1STEP 1 Look at the pump and note the error message displayed on the screen.
STEP 2STEP 2 Push the
START/STOPSTART/STOP
button to stop the alarm noise.
STEP 3STEP 3 Refer to the chart below for steps to resolve the problems.
PROBLEM SOLVING INSTRUCTIONS
Error messages and instructions
Please refer to the detailed Instructions for Use booklet that comes with your pump for more information.
Nutricia Ltd.
124 Favona Road, Favona, Auckland, 2024, New Zealand.
Nutricia Clinical Care Line: 0800 636 228 | www.nutriciaflocare.com
Problem Instructions
NO SETNO SET Press
ON/OFFON/OFF
to switch o the pump. Insert the Flocare® Infinity™ set into the pump following instructions
for use. Press
ON/OFFON/OFF
to restart the pump.
PUSH STARTPUSH START The pump has been untouched in hold mode for over 3 minutes. Extend the hold mode by a further 3minutes
by pressing
START/STOPSTART/STOP
. Check the pump programming is correct the pump and press
START/STOPSTART/STOP
to
start the pump.
END OF DOSEEND OF DOSE The programmed dose/volume has been administered. Switch o the pump by pressing
ON/OFFON/OFF
.
PROGPROG This could be a result of holding your finger down on the
CLRCLR
button for too long, or no flow rate has been
installed. Make sure the correct flow rate is programmed.
DOORDOOR The door is not correctly closed. Make sure the door is properly closed prior to starting a feedingprogram.
AIRAIR Press
START/STOPSTART/STOP
. Check if the set is inserted correctly and check the air sensor. Remove the air in the
set by pressing the
FILL SETFILL SET
key once. Once all visible air has been removed from the feeding set, press
FILL SETFILL SET
to pause the pump movement. Recommence feeding by pressing
START/STOPSTART/STOP
.
BATTBATT Connect the charging cable to the pump, and plug the adaptor in to an electrical outlet. Ensure that the adaptor (the
part that connects to the electrical outlet) is clicked in to place, sitting flat and flush - a green light should display
when properly connected. A full charge takes approximately 6 hours. The pump can be used whilst on charge.
BATT E + FBATT E + F Battery failure. Please contact the pumps team to organise a pump service (contact information below).
OCC INOCC IN Press
START/STOPSTART/STOP
to silence the alarm. Check the feeding set for any kinks in the tubing or visible
blockages. If required, remove the set from the pump and clean the pump sensors before reinserting the
cartridge back in to place. Press
START/STOPSTART/STOP
to recommence feeding.
LOCKLOCK The programming feature is locked in the set-up mode of the pump.
Refer to instruction booklet to unlock.
ER01 - ER99ER01 - ER99 Electronic error. Switch the pump o, make sure the pump door is closed and turn the pump back on. If the
error persists, please refer the pump for service by contacting Nutricia.
NO PLUGNO PLUG First check the adaptor is firmly pressed down on the area housing the two pins, you should hear a click when this
is in place. Reconnect to the wall. If there is still no plug symbol on the pump and no green light on the adaptor,
try using another wall outlet. If the pump is still not able to charge, request a replacement of the adaptor.
OCC OUTOCC OUT
SYMBOLSYMBOL
Nutricia Pumps Team –0800 222 430 Mon-Fri: 9am-5pm NZDT ^
^Excludes public holidays
NC4047-Mar20 / NUT1101