NXP Semiconductors OM15008 User manual

UM10911
OM15008 smart lighting module
Rev. 1.1 —29 April 2016
User manual
Document information
Info
Content
Keywords
JN5169, remote control, lighting, SSL, LED, PCB antenna, ZigBee, NFC
Abstract
This user manual provides basic information about the OM15008
reference design. The OM15008 board contains a RF remote control for
lighting applications. The board must be supplied with a low DC voltage
of typical 2.5 V.
The JN5169 has 512 kB internal flash memory so no external flash
memory is needed.

NXP Semiconductors
UM10911
OM15008 smart lighting module
UM10911
All information provided in this document is subject to legal disclaimers.
© NXP Semiconductors N.V. 2014. All rights reserved.
User manual
Rev. 1.1 —29 April 2016
2 of 19
Contact information
For more information, please visit: http://www.nxp.com
Revision history
Rev
Date
Description
0.0
20150624
Initial version
0.1
20150624
Change NT3H1201 with NT3H1101, connect NFC Field Detect signal to JN5169
1.0
20151117
First released
1.1
20160419
Add the JN-AN-1221 reference for binary file
1.2
20160429
Add the new Production Flash Programmer JN-SW-4107

NXP Semiconductors
UM10911
OM15008 smart lighting module
UM10911
All information provided in this document is subject to legal disclaimers.
© NXP Semiconductors N.V. 2014. All rights reserved.
User manual
Rev. 1.1 —29 April 2016
3 of 19
1. Safety warning
Warning
Lethal voltage and fire hazard
The non-insulated high voltages that are present when operating this product constitute a risk
of electric shock, personal injury, death and/or ignition of fire.
This product is intended for evaluation purposes only. It shall be operated in a designated test
area by personnel qualified according to local requirements and labor laws to work with
non-insulated mains voltages and high-voltage circuits. This product shall never be operated
unattended.
The board must be connected to (rectified) mains voltage. Avoid touching the demo
board while it is connected to the mains voltage. An isolated housing is obligatory when
used in uncontrolled, non-laboratory environments. Galvanic isolation, of the mains
phase using a variable transformer is always recommended.
a. Isolated
b. Non isolated
Fig 1. Variable transformer isolation symbols
2. Introduction
The OM15008 smart lighting module is a highly versatile board that can be used in all
kinds of applications but focuses on lighting applications. Because the board is so
versatile, several components might left out in a specific application. The board is split up
in two parts:
RF part containing JN5169
RF antenna
The board can be placed on top of a Large Signal Board (LSB) that containing a LED
driver in order to create a fully functional remote controllable lamp.
The JN5169 is an ultra-low power, high performance wireless microcontroller suitable for
ZigBee applications, remote control and Active RFID.
The PCB antenna can also be removed in order to connect an external antenna via a
coaxial wire.
If the JN5169 with 512 kB memory is mounted on this board, then the antenna matching
components need to be modified. More on this can be found in sections 6 and 7 of this
manual.

NXP Semiconductors
UM10911
OM15008 smart lighting module
UM10911
All information provided in this document is subject to legal disclaimers.
© NXP Semiconductors N.V. 2014. All rights reserved.
User manual
Rev. 1.1 —29 April 2016
4 of 19
3. Specification
DC supply voltage of typically 2.5 V
Integrated PCB antenna
Minimum of external components needed
Low standby power
4 digital outputs
1 digital input
1 analog input or digital input
Table 1. OM15008 module specification
Parameter
Comment
Min.
Typ.
Max.
Units
DC supply voltage
2
2.5
3.6
V
power consumption
measured at 2.5 V supply voltage
-
45
-
mW
ambient temperature
25
-
+125
°C
4. Board connections
Fig 2. Board connections

NXP Semiconductors
UM10911
OM15008 smart lighting module
UM10911
All information provided in this document is subject to legal disclaimers.
© NXP Semiconductors N.V. 2014. All rights reserved.
User manual
Rev. 1.1 —29 April 2016
5 of 19
5. Programming the board
The OM15008 board can be programmed using the Atomic USB programming dongle +
OM15037 adapter board and a standard USB cable. The Atomic programming dongle
can be ordered from www.atomicprogramming.com. Contact your local NXP support
office for the OM15037 adapter board.
A flex foil is used to connect the OM15008 board to the OM15037 board. Suitable flex
foils can be found in Table 2.
Table 2. Flex foils
Manufacturer
Manufacturer code
Supplier
Supplier code
Molex
98267-0233
Farnell
1079968
WURTH ELEKTRONIK
686608200001
Farnell
1908567
Note: the flex foil must be twisted when connecting the two boards. Twisted means that
on board the metal contacts of the flex foil are facing up and on the other board the
contacts are facing towards the board as is depicted in Fig 3.
Fig 3. Programming cable connections
The Atomic programming board supplies the OM15008 board with 3.3 V during the
programming. The programming board contains a voltage regulator that derives 3.3 V
from the 5 V that is supplied from the USB port.
Driver of USB serial interface and programming software can be found in the Production
Flash Programmer JN-SW-4107, full details provided in Production Flash Programmer
User Guide JN-UG-3099.
Do not supply the OM15008 board via an external supply during programming.
The programming method described here is suitable for use in prototypes. However, for
mass production, either program the flash before assembly or after assembly use
programming pads on the PCB and needles rather than a programming connector.
Refer to JN-AN-1221 for the binary file generation.

NXP Semiconductors
UM10911
OM15008 smart lighting module
UM10911
All information provided in this document is subject to legal disclaimers.
© NXP Semiconductors N.V. 2014. All rights reserved.
User manual
Rev. 1.1 —29 April 2016
6 of 19
6. Schematic
The OM15008 board can also be fitted with a JN5169 which has 512 kB embedded flash,
lower standby power and 10 dBm transmit power. The antenna matching circuit and
crystal oscillator component value's must be changed when the JN5169 is mounted.
(1) DIO17/SPISMISO/SIF_D/COMP1M/PWM4.
(2) DIO16/SPISMOSI/SIF_CLK/COMP1P.
(3) DIO1/ADE/SPISEL2/ADC4/PC0.
(4) DIO0/ADO/SPISEL1/ADC3.
(5) DIO19/SPISEL0.
(6) DIO18/SPIMOSI.
(7) DO1/SPIMISO/PWM3.
(8) DO0/SPICLK/PWM2.
Fig 4. JN5169 design with minimum required external components

NXP Semiconductors
UM10911
OM15008 smart lighting module
UM10911
All information provided in this document is subject to legal disclaimers.
© NXP Semiconductors N.V. 2014. All rights reserved.
User manual
Rev. 1.1 —29 April 2016
7 of 19
7. Bill of Material application
Table 3. Bill of material
Absolutely required
Reference
Description and values
Part number
Manufacturer
Yes
C2
1.8 pF
GRM1555C1H1R8CA01D
MURATA
Yes
C3
1 pF
GRM1555C1H1R0CA01D
MURATA
Yes
C31
12 pF
GRM1555C1H120JA01
MURATA
Yes
C32
12 pF
GRM1555C1H120JA01
MURATA
Yes
C34
100 nF
GRM155R71C104KA88D
MURATA
Yes
C36
100 nF
GRM155R71C104KA88D
MURATA
Yes
C38
10 nF
GRM155R71H103KA88D
MURATA
Yes
C39
100 nF
GRM155R71C104KA88D
MURATA
Yes
C40
47 pF
GRM1555C1H470JA01
MURATA
Yes
C42
100 nF
GRM155R71C104KA88D
MURATA
Yes
C43
100 nF
GRM155R71C104KA88D
MURATA
Yes
C49
2.2 F
GRM188R71A225KE15D
MURATA
Yes
L4
4.3 nH
LQG15HN4N3S02
MURATA
Yes
L5
3.0 nH
LQG15HN3N0S02
MURATA
Yes
R15
43 k
RC0402FR-0743KL
YAGEO
Yes
R4
1 k
RC0402FR-071KL
YAGEO
Yes
U4
JN5169
JN5169
NXP
Yes
Y2
32 MHz Xtal
X32M000000S039A
AEL

NXP Semiconductors
UM10911
OM15008 smart lighting module
UM10911
All information provided in this document is subject to legal disclaimers.
© NXP Semiconductors N.V. 2014. All rights reserved.
User manual
Rev. 1.1 —29 April 2016
8 of 19
8. Board layout
Fig 5. Top and bottom OM15008 layout
Note: the top side of the OM15008 board is facing towards the top side of the Large
Signal Board (LSB).

NXP Semiconductors
UM10911
OM15008 smart lighting module
UM10911
All information provided in this document is subject to legal disclaimers.
© NXP Semiconductors N.V. 2014. All rights reserved.
User manual
Rev. 1.1 —29 April 2016
9 of 19
9. Board dimensions
Fig 6. Board dimensions
10. Functional description
10.1 Pinout
The OM15008 board has a programming connector and two headers:
Table 4. Pin list for the programming connector
Pin
Pin name
JN5169 pin
Function
Electrical
J3.1
DIO5
27 (DIO5)
0 V to 3.6 V
J3.2
DIO4
26 (DIO4)
0 V to 3.6 V
J3.3
SPIMISO
22 (SPIMISO)
0 V to 3.6 V
J3.4
DIO7
29 (DIO7)
digital I/O (UART)
0 V to 3.6 V
J3.5
DIO6
28 (DIO6)
digital I/O (UART)
0 V to 3.6 V
J3.6
RESETN
3 (RESET_N)
digital I/O (Reset_not signal for microcontroller)
0 V to 3.6 V
J3.7
GND
-
ground
0 V
J3.8
VCCRF
9/30 (VDDA/VDDD)
supply
0 V to 3.6 V

NXP Semiconductors
UM10911
OM15008 smart lighting module
UM10911
All information provided in this document is subject to legal disclaimers.
© NXP Semiconductors N.V. 2014. All rights reserved.
User manual
Rev. 1.1 —29 April 2016
10 of 19
Table 5. Pin list for header J2
Pin
Pin name
JN5169 pin
Function
Electrical
J2.1
RESETN
3 (RESET_N)
0 V to 3.6 V
J2.2
DIMMER_BLEED
17 (DIO1)
bleeder output when the board is used in dimmer
tolerant solutions
0 V to 3.6 V
J2.3
VAUX_MON
32 (DIO9)
VAUX monitor input when the board is applied in low
cost solutions
0 V to 3.6 V
J2.4
PWM1
33 (DIO10)
PWM1 output (Brightness control)
0 V to 3.6 V
J2.5
PWM2
34 (DIO11)
PWM2 output (CCT control when the board is used in
tunable white solution)
0 V to 3.6 V
J2.6
ON
37 (DIO13)
ON/OFF output
0 V to 3.6 V
Table 6. Pin list for header J6
Pin
Pin name
JN5169 pin
Function
Electrical
J6.1
ADCIN
15 (ADC1)
1 (DIO16)
input for AD converter
input for comparator
0 V to 3.6 V
0 V to 3.6 V
J6.2
GND
-
0 V
J6.3
VCCRF
9/30 (VDDA/VDDD)
0 V to 3.6 V
The RESET_N pin of the JN5169 is connected to J3.6 and J2.1 and susceptible for
noise. So do not connect a programming cable or long wires to these pins. The
RESET_N pin is connected to VCCRF via a pull up resistor. The minimum value of this
resistor depends on the programming board that is used: if for example the Atomic
programming board is used, then the minimum value of the pull-up resistor depends on
the maximum current that the FTDI chip on the Atomic programming board can sink.
Header J2 has 4 digital outputs to the LSB that can be used to control the LED driver on
the LSB. The function of these pins depends on the LSB on which the OM15008 board is
mounted and the software that is used.
The VAUX_MON input can be used for standby voltage control in combination with
specific large signal boards.
There are RC-filters on the PWM outputs as the board is operating in a noisy
environment. In this way is prevented that noise is injected from the LSB into the DIO's
which might cause problems. The filters are placed as close as possible to the DIO pins
of the JN5169. Ideally the 470 pF capacitors should have been placed directly between
the DIO-pins and ground, but because the PWM output is switching this would result in
switching spikes through the capacitors. For that reason the filter capacitors are placed
between the pin's of J2 and ground and then they are connected to the DIO pins via a 2.2
kresistor.
Header J6 is used for supplying the board and J6.2 is an input that can be routed to 2
different pins: ADC1 and DIO16. The first input is an ADC and it can be used to monitor
e.g. the bus voltage. The second input is a comparator and this input can be used for
synchronizing the PWM frequency with the mains frequency.