OAKWORKS Celesta Lift User manual

OAKWORKS®Lift Tables
Celesta®Deluxe
Celesta®Lift
Celesta®PerformaLift
AVAILABLE WITH:
• RECTANGULAR FLAT TOP
• ROUND CORNER FLAT TOP
• BACKREST TOP
• FLEX TOP (SHOWN HERE)
INSTRUCTION MANUAL
www.oakworks.com · 717.235.6807
ELECTRIC LIFT & TILT
MANUAL TOP
ELECTRIC LIFT & TILT
ELECTRIC TOP
ELECTRIC LIFT & TILT
MANUAL TOP

© Copyright 2007
OAKWORKS®, Inc.
Manual Part Number
MMMNST0003
Revision date: 10.26.09
2nd Edition, October 2009
1st Edition, September 2003
English, Printed in USA
All rights are reserved. No part
of this document may be
photocopied, reproduced or
translated to another language
without prior written consent
of OAKWORKS®, Inc.
OAKWORKS®is a registered
trademark of OAKWORKS®, Inc.
Notice
The information contained in this
document is subject to change
without notice and should not
be construed as a commitment by
OAKWORKS®, Inc.
OAKWORKS®, Inc. assumes no
responsibility for any errors that
may appear in this document nor
does it make expressed or implied
warranty of any kind with regard
to this material, including, but not
limited to, the implied warranties
of merchantability and fitness for
a particular purpose.
OAKWORKS®, Inc. shall not be
liable for incidental or consequen-
tial damages in connection with or
arising out of the furnishing, per-
formance, or use of this document
and the program material which it
describes.

TABLE OF CONTENTS
TABLE OF CONTENTS
Symbol Identification .................................................................................. pg 1
Important Safety Instructions........................................................................ pg 2
Section I: Product Description & Photo
Celesta®Deluxe ................................................................................pg 3
Celesta®Lift ......................................................................................pg 4
Celesta®PerformaLift .......................................................................pg 5
Section II: Installation
Leveling Instructions .................................................................. pg 6
Section III: Directions for Use
Foot Control Operations
Celesta®Deluxe, Celesta®Lift & Celesta®PerformaLift ........pg 8
Hand Control Operations
Celesta®Lift & Celesta®PerformaLift ...................................pg 9
Hand Control Operations
Celesta®Deluxe .......................................................... pg 10 & 11
Manual Top Operations
Celesta®Lift & Celesta®PerformaLift ........................................pg 12
Grounding ................................................................................. pg 13
Section IV: Accessories
Side Arm Rests .....................................................................pg 14 & 15
Lowered Arm Rest Shelf ............................................... pg 16
QuickLock™ Face Rest .............................................................pg 16
Section V: Troubleshooting
Thermal Limiting Switch ..................................................... pg 17
If the table will not change position .....................................pg 17
Questions to ask before calling Customer Service..........pg 17
Section VI: Care & Cleaning .........................................................................pg 18
Section VII Product Identification ..............................................................pg 19
Section VIII: Specifications .................................................................... pg 20
Contact Information ...................................................................... back cover
TABLE OF CONTENTS

SYMBOL IDENTIFICATION
SYMBOL IDENTIFICATION
1
SYMBOL IDENTIFICATION
This symbol, when used in this manual and on product labels, represents
a caution warning. Be sure to read and comply with all precautions and
warnings.
This symbol, when used in this manual and on product labels, warns
against an electrical shock hazard. Be sure to observe and comply with all
warnings.
This symbol, when used in this manual or on product labels, indicates a
Protective Earth (Ground) Terminal.
This symbol when used in this manual or on product labels, warns that
during transport there should be no stacking of containers.
This symbol, when used in this manual or on product labels, indicates that
the product should be protected from moisture. The humidity specifications
for Transport & Storage are listed on page 31.
This symbol, when used in this manual or on product labels, indicates that
information is given regarding the recommended temperature limits
during transport and storing.
This symbol, when used in this manual or on product labels, indicates the
date of manufacture of the device.
This symbol, when used in this manual or on product labels, indicates
alternating current (AC).
This symbol, when used in this manual or on product labels, indicates
direct current (DC).
~
----

2
IMPORTANT SAFETY INSTRUCTIONS
PRODUCT DESCRIPTION
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical furnishing, basic precautions
should always be followed, including the following:
DANGER - To reduce the risk of electrical shock always unplug this
furnishing from the electrical outlet before cleaning.
WARNING - To reduce the risk of burns, fire, electric shock of injury to
persons:
1. Unplug from outlet before putting on or taking off parts.
2. Close supervision is necessary when this furnishing is used by, or near
children, invalids, or disabled persons.
3. Use this furnishing only for its intended use as described in these
instructions. Do not use attachments not recommended by the manufacturer.
4. Never operate this furnishing if it has a damaged cord or plug, if it is
not working properly, if it has been dropped or damaged, or dropped
into water. Contact Oakworks Customer Service before use.
5. Keep the cord away from heated surfaces.
6. Never drop or insert any object into any opening.
7. Do not use outdoors
8. Do not operate where aerosol (spray) products are being used or
where oxygen is being administered.
9. To disconnect, remove plug from outlet.
10. Risk of electric shock - Connect this furnishing to a properly gounded
outlet only. See Grounding Instructions.
11. Weight Limit: (patient and accessories) 625 lbs.
12. Be certain that the table is completely lowered without any tilt being
present prior to discharging an ambulatory patient. The patient may
lose balance and fall.
13. Electrical Shock Hazard. The power supply/control module is located
below the base of the table. No user serviceable parts are inside. Refer servicing
to qualified personnel. Unplug wall connector prior to contact with any
cables connected to the power supply.
14. Keep fingers and hands away from underside of table top pinch points.

Table Specs* :
• Lifting Capacity: 625 lbs. (284 kg)
• Heights: 24”-35” (58 - 86 cm)
• Widths: 27”, 29”, 31” or 33”
(69, 74, 79, or 84 cm)
• Length: 72” (183 cm)
• Top: Electric Access Design Top
• Padding: Plush, 4” Aero•Cel™ or
6” Aero•Cel™
• Upholstery: TerraTouch™, UltraTouch™
* Published weight and height may differ slightly due to options
chosen, natural material variations and padding density.
For electrical specs, see Specifications Chart
3
PRODUCT DESCRIPTION
PRODUCT DESCRIPTION
Celesta Deluxe™
- Model P5CA
Leg Rest
Auto-adjusting
arm rests
Upholstered
Top (Celesta
Access End)
Hand
Control (1)
Foot Control (1)
Electronic
Lift Towers
(2)
Head rest

4
PRODUCT DESCRIPTION
PRODUCT DESCRIPTION
Celesta Lift™
- Model P5CT
Manual
Back Rest
Control (2)
Manual Leg
Rest Control
(2)
Leg Rest
Table Specs* :
• Lifting Capacity: 625 lbs. (284 kg)
• Heights: 24”-35” (58 - 86 cm)
• Widths: 29” or 31” (74 or 79 cm)
• Length: 72” (183 cm)
• Top: Manually Controlled
Access Design Top
• Padding: Plush, 4” Aero•Cel™ or
6” Aero•Cel™
• Upholstery: TerraTouch™, UltraTouch™
* Published weight and height may differ slightly due to options
chosen, natural material variations and padding density.
For electrical specs see Specifications Chart
Auto-adjusting
arm rests
Upholstered
Top (Celesta
Access End)
Hand
Control (1)
(optional)
Foot Control (1)
Electronic
Lift Towers
(2)
Head rest

Table Specs* :
• Lifting Capacity: 625 lbs. (284 kg)
• Heights: 24”-35” (58 - 86 cm)
• Widths: Dependent on top
27”, 29”, 31” 33”
(69, 74, 79, or 84 cm)
• Length: Dependent on top
72”, 73”, 75”
(185, 186 or 190 cm)
• Tops: Rectangular, Rounded Corner,
Back Rest & Flextop
• Padding: Plush (standard), Semi-Firm,
Firm, 4” Aero•Cel™ or
6” Aero·Cel™
• Upholstery: TerraTouch™ (standard),
Ultratouch
* Published weight and height may differ slightly due to options
chosen, natural material variations and padding density.
For electrical specs, see Specifications Chart
5
PRODUCT DESCRIPTION
PRODUCT DESCRIPTION
Celesta
PerformaLift™
- Model P5
AVAILABLE WITH:
• RECTANGULAR
FLAT TOP
• ROUND CORNER
FLAT TOP
• BACKREST TOP
• FLEX TOP
(SHOWN HERE)
Leg Rest
Upholstered
Top
Hand
Control (1)
(optional)
Foot Control (1)
Electronic
Lift Towers
(2)
Manual
Back Rest
Control (2)
Manual Leg
Rest Control
(2)

6
INSTALLATION
INSTALLATION
Leveling Instructions
The Celesta and PerformaLift tables come completely assembled and
ready to use. Plug the cord into a functioning outlet that is rated for the table.
Arrange the power cord and control cords so that they will not create a
tripping hazard and where the controllers are located to you liking and
are conveniently accessible.
LEVELING INSTRUCTIONS:
If Table Will Not Sit Flat on the Floor:
The Celesta and Performance Lift Tables are equipped with Leveler Feet
that adjust to level the table on uneven floors. To adjust the Leveler Feet
to suit common floor differences you will need to use a 1/2” open-end
wrench or an adjustable wrench.
1/2” Open-end Wrench
Leveler Foot
INSTALLATION

7
INSTALLATION
Leveling Instructions
INSTALLATION
To Adjust the Leveler Feet:
1. Place the table in the location where you plan to use it.
2. Rock the table to determine if it is level with the floor. If the table
rocks back and forth at all, the foot that clears the floor when you rock
the table will need adjustment.
3. Adjust the Leveler Foot by first loosening the locking nut found just
above the rubber Leveler Foot with the open-end wrench.
4. Lower the adjustable rubber Leveler Foot until it meets the floor
snugly. Tighten the locking nut against the wooden leg of the table
with the open-end wrench to fix the Leveler Foot in position.
5. Rock the table again to be sure adjustments have stabilized the table.
If necessary make any additional adjustments in the same way.
Locking Nut
Tighten Locking Nut
Locking
Nut

The Oakworks Lift Tables offer a variety of positioning capabilities
when client comfort is critical. They are especially effective for
professional protocols that require specific positioning of the
client and provide superior ergonomics for the comfort level of the
professional therapist as well.
The OAKWORKS®Celesta Deluxe, Lift and PerformaLift come complete
with a foot control and hand control to operate the height and angle of
the table. The back rest and leg rest features of the top are manually adjusted
on the Celesta Lift and PerformaLift. The Celesta Deluxe features a top that is
operated electrically by a hand control.
FOOT CONTROL OPERATIONS
Foot Control:
Operate the foot control as shown below to raise or lower the height
of the table. When operating the table’s controls, be sure to observe all
cautions and warnings as given in the manual.
Foot Control: (used only to change height of table)
UP DOWN
CAUTION
When operating the
table controls be sure
to observe all cautions
and warnings given in
the manual to prevent
injury to both operator
and client.
8
DIRECTIONS FOR USE
DIRECTIONS FOR USE
Adjusting Height - Foot control
Celesta®Deluxe
Celesta®Lift
Celesta®
PerformaLift
DIRECTIONS FOR USE

Left Side
Tilt Control:
- activates tilt up
to 15º
- positioning stops
when table is level;
press again for
complete reverse.
9
DIRECTIONS FOR USE
DIRECTIONS FOR USE
Adjusting Height and Tilt Angle - Hand Control - Celesta Lift, Celesta PerformaLift
Hand Control:
The Hand Control operates the tilt angle and the height of the table with
the touch of a button. Follow the directions below to access these functions.
Height
Controls
Tilt
Controls
HAND CONTROL OPERATIONS
Right Side
Tilt Control:
- activates tilt up
to 15º
- positioning stops
when table is level;
press again for
complete reverse.
4
Table UP Control:
-
elevates tabletop
- tilt is preserved
during elevation
Table DOWN
Control:
- lowers tabletop
- table is lowered
from any position
CAUTION
Do not sit on the elevated
Back Rest or Leg Rest.
CAUTION
Do not leave clients
unattended when table
is tilted near its limits.
3
12
Celesta®Lift
Celesta®
PerformaLift

10
DIRECTIONS FOR USE
DIRECTIONS FOR USE
Adjusting Height and Tilt Angle - Hand Control - Celesta Deluxe
HAND CONTROL OPERATIONS
CAUTION
Do not sit on the elevated
Back Rest or Leg Rest.
CAUTION
Do not leave clients
unattended when table
is tilted near its limits.
Celesta®Deluxe
Back Rest
Controls
Leg Rest
Controls
Backrest Control:
- activates backrest
down to level position
Backrest Control:
- activates backrest
up to 60º
2
Leg Rest
UP Control:
- elevates leg rest
up to 40º
Leg Rest
DOWN Control:
- lowers leg rest
CAUTION
Do not sit on the elevated
Back Rest or Leg Rest.
1
34

11
DIRECTIONS FOR USE
Tilt
Controls
Height
Controls
Table UP Control:
- elevates tabletop
- tilt is preserved
during elevation
Table DOWN
Control:
- lowers tabletop
- table is lowered from
any position
Right Side
Tilt Control:
- activates tilt up to 15º
- positioning stops
when table is level;
press again for
complete reverse.
Left Side
Tilt Control:
- activates tilt up to 15º
- positioning stops
when table is level;
press again for
complete reverse.
56
78
CAUTION
Do not leave clients
unattended when table
is tilted near its limits.
HAND CONTROL OPERATIONS
Celesta®Deluxe
DIRECTIONS FOR USE
Adjusting Height and Tilt Angle - Hand Control - Celesta Deluxe

12
DIRECTIONS FOR USE
Operating the Manual Top - Celesta Lift, Celesta PerformaLift
OPERATING THE MANUAL TOP
To Raise the Back Rest:
Raise the backrest by pulling it up from the head end of the table to the proper
position for the procedure. It is recommended that the client takes some of their
weight off the backrest while you lift.
CAUTION
Do not sit on the elevated
Back Rest or Leg Rest.
CAUTION
Do not release backrest
without supporting
the backrest and client
Celesta®Lift
Celesta®
PerformaLift
(backrest or flex top)
DIRECTIONS FOR USE
Back Rest
Top at total recline
Back Rest
Control
Raises Back Rest up to 60º Back Rest Control
To Raise the Leg Rest:
Raise the leg rest by pulling it up from the lower center end of the table to the
proper position for the procedure. It is recommended that the
client takes some of their weight off the leg rest as you lift.
Leg Rest
Raises Leg Rest
up to 55º
Leg Rest at
total recline
Celesta®Lift
Celesta®
PerformaLift
(flex top)
CAUTION
Do not release leg rest
without supporting
the leg rest and client
To Lower the Back Rest:
Support the backrest and weight of the client with one hand. Push the locking
handle towards the center of the table slowly to loosen the locking mechanism and
lower the backrest to the desired position. Release the handle and the backrest
will stay in place. It is recommended that the client lifts themselves off the back-
rest to take some of the weight off the backrest while you move it into position.
Leg Rest
Control Leg Rest
Control
To Lower the Leg Rest:
Support the leg rest and weight of the client with one hand. Push the locking
handle towards the center of the table slowly to loosen the locking mechanism and
lower the leg rest to the desired position. Release the handle and the leg rest will
stay in place. It is recommended that the client lifts the weight off the leg rest while
you move it into position.

13
DIRECTIONS FOR USE
Grounding
DIRECTIONS FOR USE
This product must be grounded. If it should malfunction or breakdown,
grounding provides a path of least resistance for electrical current to reduce
the risk of electric shock. This product is equipped with a cord having an
equipment-grounding conductor and a grounding plug. The plug must be
plugged into an appropriate outlet that is properly installed and grounded in
accordance with all local codes and ordinances. See U.S. sample below.
This product is manufactured for use on a nominal 120-volt circuit for the
United States and a nominal 220-volt circuit for use in Europe. The plug has
a grounding pin in a pattern that varies by country as shown in the Product
Identification section of this manual. Make sure that the product is connected
to an outlet having the same configuration as the plug.
Correct Implementation Incorrect Implementation
DANGER-Improper connection of the equipment-grounding conductor
can result in a risk of electric shock. Check with a qualified electrician
or service man if you are in doubt as to whether the product is properly
grounded. Do not modify the plug provided with the product - if it will not
fit the outlet, have a proper outlet installed by a qualified electrician.
To reduce the risk of electric shock, this furnishing has a polarized plug
(one blade is wider than the other). This plug will fit in a polarized outlet
only one way. If the plug does not fit fully in the outlet, reverse the plug. If
it still does not fit, contact a qualified electrician to install the proper outlet.
Do not change the plug in any way.
Be sure to read all
cautions, warnings
and instructions given
in the manual to prevent
injury to both operator
and client.
GROUNDING
CAUTION

14
SIDE ARM RESTS
Though the arm rests adjust automatically to remain parallel to the
floor in any position, there will still be times when you will need to
move an arm rest out of the way or remove them altogether. We
recommend that you raise the arm rest out of the way to allow a client to
get on or off the table. They are designed to be strong and will take a
reasonable amount of weight but they are not designed to be used to
sustain a person’s weight when getting on or off the table.
To Adjust the Arm Rest:
Before asking a client to mount or dismount from the table we recommend
that you move the arm rest out of the way. The arm rests are easy to move
and manually adjust. First position the tabletop with the backrest in the
upright position and all other section flat. Take hold of the arm rest
firmly and raise the arm rest up and out of the way with a steady swing
until the arm rest is in the highest upright position (see images below).
Hold it in place until your client has mounted (or dismounted) and then
actively move it back into the resting position where it will proceed to
move automatically with the table top.
The arm rest is now set and will adjust automatically as you position the cli-
ent for whatever procedure is needed.
There will be times when removal of the arm rests will be needed. This
feature is helpful when doing massage or helping someone get on or off
the table. This can be done easily and storage is conveniently located in
the under-table cabinet. They are then at hand when you are ready to
re-install.
To Remove the Arm Rest:
The arm rest frame has a notched connection to the interior of the
table top which allows it to move automatically when the table top
changes position. (cont. on next page)
Be sure to read all
cautions, warnings
and instructions given
in the manual to prevent
injury to both operator
and client.
Adjusting the Side Arm Rest
Do not place excess
weight on the Side Arm
Rests. Do not use them in
assisting the client on and
off the table.
Either Arm Rest can be
repositioned to allow a
client to get on and off
the table easily.
When making adjustments
the arm rests make certain
that the client’s arms are
away from the working
mechanism.
Do not sit on the Arm Rests.
• Side Arm Rests
DIRECTIONS FOR USE
side arm rests
CAUTION
DIRECTIONS FOR USE

15
There will be times when removal of the arm rests will be needed. This feature is
helpful when doing massage or helping someone get on or off the table.
To Remove the Arm Rest:
To remove one or both arm rests just take hold of the base of the arm rest at the
metal frame and somewhere on the cushion. Holding securely, rotate the arm rest
while at the same time pulling slightly away from the table. You will feel the notched
connection slide out as you rotate the arm rest. When you feel this you can then slide
the entire arm rest out of the connection hole very easily. Store it safely until ready for
installation.
Re-attach the armrest by sliding the arm rest frame into the hole on the backrest. Push
it in securely and allow the arm rest to rest in the parallel position. This resets the arm
rest in the proper position for the automatic adjustment feature to be activated.
Removing the Side Arm Rests
A. hand soak bowl installation
B. hand soak bowl removal
C. Manicure surface installation
The manicure arm rest installation follows the same standard installation
and removal instructions as above.
MANICURE ARM RESTS:
ABC
Do not place excess
weight on the Side Arm
Rests. Do not use them in
assisting the client on and
off the table
Either Arm Rest can be
repositioned to allow a client
to get on and off the
table easily.
When making adjustments
the arm rests make certain
that The client’s arms are
away from the working
mechanism.
IMPORTANT
CAUTION
Do not sit on the Arm Rests.
SIDE ARM RESTS: (CONT.)
• Side Arm Rests
(cont.)
CAUTION
Be sure the arm rest is fully
inserted before lowering.
DIRECTIONS FOR USE
side arm rests
DIRECTIONS FOR USE

16
DIRECTIONS FOR USE
Table Accessories
For a totally comfortable and relaxed client, add a Lowered Arm Rest Shelf
to your lift table. It’s covered in the same luxurious plush padding as the
table itself. The Lowered Arm Rest Shelf can be removed when not in use
and stored away. It can also act as a table extender, when used in place of
the face rest or at the foot of the table. For complete use & care instructions
see product instructions “Arm rest shelf instructions”
Double articulating action provides nearly limitless positioning options
with the QuickLock™Face Rest. The adjustable pad takes pressure off
sensitive facial areas while providing superb support. The QuickLock™
Face Rest can be used in both prone and supine positioning and folds
out of the way when not in use. Adjustments are made easily by loosening
the cam locks, adjusting for height and angle and then locking the cam
locks into that position.
To remove the QuickLock™Face Rest, just pull the frame from the outlets in
the end of the table until it comes free. When replacing the QuickLock™
Face Rest, just push the frame back into the outlets being sure to keep
the dowels within 3” of the table to ensure a stable connection. For complete
use & care instructions see product instructions “QuickLock Face Rest
instructions”
• Lowered Arm
Rest Shelf
• Lowered Arm
Rest Shelf with
Aromatherapy
• QuickLock™
Face Rest*
Lowered Arm Rest Shelf with
Aromatherapy, shown here with
QuickLock™ Face Rest
Lowered Arm Rest Shelf, shown here
used as a table extender
IMPORTANT
Do Not extend the dowels
of the Face Rest further than
3” from the table outlets to
ensure a stable connection.
* U.S. Patent #5,177,823
SAFETY NOTE:
CAUTION
Do not put excessive weight
or pressure on the face rest.
QuickLock™ Face Rest Important Safety Note: Maximum
Distance from edge of Table = 3”
CAUTION
Do not sit on or put excessive
weight or pressure on lowered
arm shelf.
DIRECTIONS FOR USE

17
TROUBLESHOOTING
TROUBLESHOOTING
TROUBLESHOOTING
• Is the unit plugged in?
• Does the outlet have power?
• Check all connections of the control box, is everything seated securely?
• Does the height of the table work when you press on the foot pedal?
• Does the top work when you use the hand control?
IF THE TABLE WILL NOT CHANGE POSITION
CAUTION
The table weighs as much
as 300 lbs. DO NOT lift or
move the unit without using
proper safety procedures
or equipment. DO NOT turn
the table on its side for any
reason. To do so could cause
damage to the base and
will void the warranty. There
are no serviceable items that
need this action.
IMPORTANT
Be sure to read all
cautions, warnings
and instructions given
in the manual to
prevent injury to both
operator and client.
• Check the outlet to be sure that it has power and that the power
cable is plugged in. Try each foot control and hand control to
see if any work. If any work, then possibly there is a loose connection
or a faulty controller.
• Unplug the power cable from the wall outlet.
• Make sure that all male and female connectors are firmly
pushed into each other. Even a slight misconnection can
cause a possible malfunction.
• Plug the unit back into the wall and check the controls again.
If none work, then contact customer service.
QUESTIONS TO ASK BEFORE CALLING CUSTOMER SERVICE
The Celesta Lift, Celesta Deluxe and Celesta PerformaLift tables have two lifting columns
that raise and lower the table. In addition, the Celesta Deluxe has two actuators that
allow the client to be positioned for both client and therapist comfort. Each of these
devices has a duty cycle of approximately 10%, meaning 2 minutes of operation within a
20 minute period. These devices have a thermal limiting switch to prevent overheating.
As the thermal limiting switch is engaged, the motion will slowly come to a stop. Since
there are 4 independent motion controls, the table may be able to go up but one of the
positioning motions may not work. Allow the device to rest and it will automatically
reset itself.
THERMAL LIMITING SWITCH
View complete warranty details at www.oakworks.com
WARRANTY INFORMATION