Oase AquaMax Eco Premium 6000 User manual

AquaMax Eco Premium
6000 / 12 V, 12000 / 12 V
Operating Instructions
Downloaded from www.watergardeningdirect.com

EN
19
Original operating manual.
EN
WARNING
WARNING
Disconnect all electrical units in the water from the power supply be-
fore reaching into the water. Otherwise there is a risk of injuries or
death by electrocution.
This unit can be used by children aged 8 and above and by persons
with reduced physical, sensory or mental capabilities or lack of expe-
rience and knowledge if they are supervised or have been instructed
on how to use the unit in a safe way and they understand the hazards
involved. Do not allow children to play with the unit. Only allow chil-
dren to carry out cleaning and user maintenance under supervision.
Downloaded from www.watergardeningdirect.com

20
Safety information
Electrical connection
•Special regulations apply to electrical installation in outdoor areas. Only allow a qualified elec-
trician to perform the electrical installation.
–The qualified electrician has the required professional training, knowledge and skills to per-
form electrical installations in outdoor areas. The qualified electrician can detect potential
risks and adheres to regional and national standards, regulations and directives.
–For your own safety, please consult a qualified electrician.
•Only connect the unit if the electrical data of the unit and the power supply match.
•Only plug the unit into a correctly installed outlet. Ensure that the unit is fused for a rated
fault current of max. 30 mA by means of a fault current protection device.
•Extension cables and power distributors (e.g. outlet strips) must be suitable for outdoor use
(splash-proof).
•Protect open plugs and sockets from moisture.
Safe operation
•Do not use the unit, if electrical lines or the housing are damaged.
•A damaged connection cable cannot be replaced. Dispose of the unit.
•The impeller unit inside the unit contains a magnet with a strong magnetic field that may af-
fect the operation of pacemakers or implantable cardioverter defibrillators (ICDs). Keep the
magnet at least 0.66 ft (0.2 m) away from any implant.
•Do not carry or pull the unit by its power cable.
•Route lines so that they are protected from damage and nobody can trip over them.
•Never make technical modifications to the unit.
•Only carry out work on the unit that is described in this manual.
•Only use original spare parts and accessories.
•Should problems occur, please contact the authorized customer service or OASE.
Downloaded from www.watergardeningdirect.com

EN
21
Intended use
Only use the product described in this manual as follows:
•For pumping normal pond water for filter systems, waterfall systems and water course sys-
tems.
•For use in swimming ponds if the national regulations for installers are met.
•Only operate with the original switching power pack.
•In compliance with the technical specifications. (→ Technical data)
•Only subject to adherence to the permissible water quality values. (→ Permissible water values)
The following restrictions apply to the unit:
•Never use the unit with fluids other than water.
•Never run the unit without water.
•Do not use in conjunction with chemicals, foodstuff, easily flammable or explosive substances.
•Do not connect to the domestic water supply.
•Do not use for commercial or industrial purposes.
•According to EMC (Electromagnetic Compatibility), this is a class A unit. The unit may cause
malfunctions in living environments. It is the user's responsibility to take suitable counter-
measures.
Downloaded from www.watergardeningdirect.com

22
Product description
Overview
AMX0139
1
Inlet
1 (suction side)
•
Filter casing for pond bottom filtration
2
Inlet
2 (suction side)
•
Connection of a satellite filter or skimmer.
•
The flow rate on inlet 2 and with it the intake ratio of inlet 1 and 2 is adjustable. To do so, undo
the locking mechanism and push the connection to one of the following positions:
−Position 0: Inlet 2 is closed, intake only via inlet 1.
−Position 1/2/3: Inlet 2 is opened by approx. 25/50/75 %; this means intake via inlet 1 and 2
based on the set intake ratio.
−
Position 4: Inlet 1 is closed, intake only via inlet 2.
3
Outlet (pressure side)
•Connection of the return flow to the pond (e.g. via a water course).
4
Switching power pack with power plug
•Pump power supply
5
House sleeve for outlet (recommendation).
6
Stepped hose adapter for inlet 2 and outlet (alternative).
7
Cover cap for closing inlet 2 when it is not in use.
8
Hose
clips for fastening hoses on the hose sleeves.
9
Rubber feet for pump holder for dry installation.
Downloaded from www.watergardeningdirect.com

EN
23
Symbols on the unit
The unit is dust-proof and water-tight down to 6.56 ft (4 m).
Possible hazard for persons wearing pace makers.
Only
operate the unit with a safety transformer.
Protect the unit from direct sunlight.
Never dispose of the unit with normal household waste.
Read the operating instructions.
Downloaded from www.watergardeningdirect.com

24
Installation variants
AMX0138
•Variant (a): Pond bottom filtration only
–With pond bottom filtration only, the water is drawn in only through the filter casing (in-
let 1).
–Set inlet 2 to position "0".
–Close inlet 2 with the cover cap.
•Variant (b): Pond bottom filtration and filtration via satellite filter or skimmer
–For pond bottom filtration, the water is drawn in via the filter casing (inlet 1). Inlet 2 draws in
water via a satellite filter or skimmer.
–Set inlet 2 to position "1", "2" oder "3", depending on the desired flow rate (25/50/75 %).
•Variant (c): Filtration only via satellite filter or skimmer
–Only inlet 2 draws in water via a satellite filter or skimmer.
–Set inlet 2 to position "4".
•Variant (d): Dry installation of the pump
–The pump is installed outside the pond but lower than the water level.
–With this variant, the pump must be installed without a filter casing.
Downloaded from www.watergardeningdirect.com

EN
25
Installation and connection
The pump is either installed submerged (in water) or dry (outside the water). The switching
power pack is only suitable for dry installation.
The use of the pump is only permitted subject to adherence to the specified water quality.
(→ Permissible water values)
•Pool water or salt water can impair the appearance of the unit. Such impairments are excluded
from the warranty.
WARNING
The power supply carries dangerous electrical voltage and must not be placed directly near wa-
ter. Otherwise, there is a risk of serious injury or death from electric shock.
The transformer is subject to dangerous voltage and must not be installed directly adjacent to
the water. Otherwise there is a risk of severe injuries or death by electrocution.
Install the power supply in a flood-protected position at least 2 m (6.6 ft) from the water.
CAUTION
Rotating components in the area of the intake connection and the pressure connection. Reach-
ing into the connections can lead to injuries.
Please note in particular: If a unit has stopped due to overload, it can start up unexpectedly!
Do not reach into the opening of the inlet connection or outlet connection while the power
plug is connected.
If the connections are freely accessible, e.g. if no hoses are connected, secure the connections
with a finger guard. The finger guard is available as an accessory.
NOTE
Electrical screw connections …
must always be hand-tightened to ensure safe contact and to comply with the degree of pro-
tection specified in the technical data.
are protected against splashing water, but must not be immersed or submerged in water.
NOTE
If the pump is used for conveying excessively muddy water, the impeller unit will be subject to
increased wear and will require earlier replacement.
Thoroughly clean the pond or pool before installing the pump.
Install the pump at a raised level above the bottom of the pond. This reduces intake of muddy
water.
Avoid direct sunlight when the components of the unit are not immersed, as this can cause
them to heat up considerably. Use a protective cover if necessary.
Downloaded from www.watergardeningdirect.com

26
Submerged installation of the unit
Connection
AMX0140
Connect the pump as required by the desired installation variant. (→ Installation variants)
Do not plug the power plug into the outlet yet!
Installation
AMX0142
•Position the pump horizontally on a firm, mud-free surface.
•Ensure that the pump is securely positioned.
•Only operate the pump when it is fully submerged.
A pull rope allows you to simply pull the pump out of the water.
−Pull the pull rope through the round openings on the bottom pan of the filter and make a
knot.
Downloaded from www.watergardeningdirect.com

EN
27
Dry installation of the unit
For dry installation, install the pump without a filter casing.
Conversion
AMX0144
Downloaded from www.watergardeningdirect.com