Ocean Matrix OMX-3GSDI-CAT5 User manual

USER MANUAL
OMX-3GSDI-CAT5
3GSDI Extender Over IP Via Single UTP Cat5e/6e/7
Ocean Matrix
812 Kings Highway ·Saugerties, NY 12477
www.oceanmatrix.com

OMX-3GSDI-CAT5
3GSDI Extender
The Ocean Matrix OMX-3GSDI-CAT5 extends 3GSDI signal transmis-
sion beyond the standard distance for Cat5e/6e/Cat7 cable. Consisting
of a transmitter and a receiver, this system delivers full 3GSDI signal up
to 394 feet over a single UTP Cat5e/6e/Cat7 network cable supporting
SD-SDI, HD-SDI and 3G-SDI signal input and resolutions up to
1920x1080@60Hz.
IR signal transmission allows for remote control of the source at a
secondary location using IR extension cables.
Includes
 One transmitter
 One receiver
 Two 5VDC/2A power adapters
 One IR blaster extension cable, connects to transmitter
 One IR receiver extension cable, connects to receiver
Specifications
Supported Resolutions SD-SDI 480i@60Hz, 576i@50Hz
HD-SDI 720p@50/60Hz,1080i@50/60Hz,1080p@24/25/30Hz
3GSDI 1080p@50/60Hz
Network Cable UTP Cat5e/6e/7
Transmission Range 1080p resolution up to 394 ft (120m) over Cat6
IR Remote Control Supports 20-60kHz standard IR remote controls
Power Supply 5VDC/2A
Power Consumption Transmitter 6W, Receiver 6W
Working Temperature 32°F - 140°F (0Ԩ- 60Ԩ)
Dimensions (LxWxH) 5.4 x 4.1 x 0.9 (138 x 105 x 23.8mm) TX & RX
Weight Transmitter 6.4 oz Receiver 6.43 oz (182g /180g)
SDI Rate 270Mb/s，1.485Gb/s，2.97Gb/s
SDI Signal Format SD-SDI, HD-SDI, 3GSDI
Ocean Matrix OMX-3GSDI-CAT5 Page 2

OMX-3GSDI-CAT5
Installation Requirements
1. SDI source device such as a video camera, media player,
monitoring equipment or computer.
2. SDI display device such as an SDTV, HDTV, or projector with SDI
input port.
3. UTP/STP Cat5e/6 network cable in accordance with the IEEE-568B
wiring standard up to 394 feet/120m.
Installation Safety
1. Identify the receiver and the transmitter in order to make proper
connections during installation.
2. Do not hot plug/swap when in operation.
3. Use 5VDC power supply only.
IR User Guide
1. Plug the IR blaster extension cable into the IR-out port of the Trans-
mitter TX.
2. Plug the the IR receiver extension cable into the IR-IN port of the
Receiver RX.
3. Place the emitter of the IR blaster as close as possible to the IR
receiver of the signal source device.
4. Direct the IR remote controller of the signal source device towards
the IR receiver (connected to the RX of HDMI extender), to remote
control source media playback.
Ocean Matrix OMX-3GSDI-CAT5 Page 3

OMX-3GSDI-CAT5
7 8 9
11
10
4
6
51 2 3
Ocean Matrix OMX-3GSDI-CAT5 Page 4
Transmitter
Receiver
Rear of Both Units
12 13
6 RX Power Input 5VDC
7 RX Reset Button
8 RX Signal Input
11 TX & RX Power Status Indicator
12 TX & RX Data Transmission Indicator
13 TX & RX Network Connection Indicator
1 TX Power Input 5VDC
2 TX Reset Button
3 TX Signal Output
10 RXSDI Signal Output
9 RX IR Extension Cable Port
4 TX IR Blaster Extension Cable Port
5 TX SDI Signal Input

OMX-3GSDI-CAT5
Installation Procedures
Cat5/6 Network Cable—follow the IEEE-568B wiring standard:
1. White/Orange
2. Orange
3. White/Green
4. Blue
CONNECTION
Transmission distance up to 394 ft (120m) over single Cat6
Troubleshooting
Display shows “ Waiting for Connection”
 Ensure power supply is firmly connected.
Display shows “ Signal Loss”
 Check signal input of the TX.
 Connect the signal source directly to the display device to
ensure there is a signal output. Change the signal source if
necessary.
Degraded video signal
 Check cable lengths between the TX to the switch, the
switch to RX.
 Ensure the connection between each level is within
required ranges.
 Press the RESET button on the TX/RX front panel.
 Ensure all connections are secure.
Ocean Matrix OMX-3GSDI-CAT5 Page 5
5. White/Blue
6. Green
7. White/Brown
8. Brown
TX RX
SDI In SDI Out TV
HD
Camera UTP Cat5e/6e/7
Cable

Ocean Matrix
812 Kings Highway
Saugerties NY 12477
www.oceanmatrix.com
SAFETY PRECAUTIONS
1. To prevent fire or shock hazard, do not expose this equipment to high
humidity and/or dust. Do not use in an unprotected outdoor installation
nor any area classified as overly damp or wet.
2. The temperature for installation should be kept between 32°F to 140°F
(0°C to 60°C). Avoid direct sunlight exposure or extreme changes of
temperature over a short period of time.
3. Do not disassemble the unit or place it on an unstable base.
4. Do not drop the unit and avoid heavy impact.
5. This unit should not be permanently installed unless proper ventilation is
provided. Any enclosure openings must not be blocked or covered as they
protect the unit from overheating.
6. Before cleaning, turn off the power and unplug the unit from all connec-
tions. Use a damp cloth. Do not use liquid cleaners nor aerosol cleaners.
7. Do not overload outlets and extension cords as this may result in a risk of
fire or electric shock.
8. Enclosure entry is dangerous. Never push objects of any kind, including
liquids, into this unit through openings as they may touch dangerous
voltage points or short-out parts that could result in a fire or electric shock.
9. Do not attempt to open or service this unit yourself as opening or removing
covers may expose you to dangerous voltage and other hazards.
10.There are no user-serviceable parts inside the unit. If the unit requires
service contact your authorized dealer, or an authorized repair service
company.