Oceanled SPORT Series User manual

L I GH T. Y E A R S A H E A D . WWW.OCEANLED.COM
OceanLED MAN-000048 / SPORTS SERIES / REVISION 1
INSTALLATION & OPERATION MANUAL
SPORT SERIES

SPORTS SERIES Single / Dual / Colours / DMX.
INSTALL & OPERATION MANUAL
1
Preface
READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL
CAUTION
(Risk Group 2): Possibly hazardous optical radiation emitted from this product. Do not stare at operating
lamp. May be harmful to the eye.
CLASS 3
This equipment is designed to operate at voltages of less than 50v DC.
WARNINGS
Before installing your OceanLED Light, read and follow all warning notices and instructions that are included.
Failure to follow safety warnings and instructions can result in property damage, severe injury, or even death.
Before installing your OceanLED Light, check local laws for restrictions regarding the use of colored lights
in your area.
Ensure the mounting location is flat and check internally for ease of access if there is a rib, strut, or other
hull that may interfere with the installation. Avoid mounting lights on surfaces that are subjected to high-
speed water impact, such as planing surfaces.
It is advised not to operate lights out of water for a period longer than 5 minutes. Please make sure lights are
fully cooled down before re-testing out of the water. Exceeding this may cause damage to the light unit.
Salt is an inherently corrosive material. Metal parts and certain natural and man-made surfaces are
particularly susceptible to corrosion and deterioration when used in and around saltwater. Some OceanLED
lights contain combinations of plastic and polymer products that are impervious to saltwater corrosion;
however, screws and fasteners used for the installation must be of a marine-grade type stainless steel or
equivalent and should be monitored annually to ensure the lights remain in service for years to come.
Never use solvents such as cleaners or fuel, as these products may contain strong solvents like acetone.
Solvents can attack many plastics, greatly reducing their strength and causing irreversible damage to
special lens coatings and cable sheathings. Never connect or disconnect lights with power applied, as
irreversible damage may occur. Ensure the polarity of power connections is correct. Failure to do this may
invalidate the warranty.
Never clean lights using a high-pressure jet wash; this will invalidate the warranty. Please avoid coating the
front of the light/lens without consulting OceanLED. Failure to do so will invalidate your warranty.
If bottom painting your lights, ensure the lens and the white plastic retaining ring are free of any paint or
residue.
Do not submerge your cable ends in water; cables and connections exposed to underwater submersion will
not be covered by the warranty. Mounting the light in any other configuration other than those described in
this guide will invalidate its warranty.

SPORTS SERIES Single / Dual / Colours / DMX.
INSTALL & OPERATION MANUAL
2
DANGER
RISK OF ELECTRIC SHOCK OR ELECTROCUTION
This underwater light must be installed by a licensed or certified electrician in accordance with all applicable
local codes and ordinances. Improper installation will create an electrical hazard which could result in death
or serious injury to swimmers, installers, or others due to electrical shock, and may also cause damage to
property.
Always disconnect the power to the light at the circuit breaker before servicing the light. Failure to do so
could result in death or serious injury to serviceman, swimmers, or others due to electrical shock.
PRETEST
Always test the lights prior to installation. Failure to do this may result in additional installation time and could invalidate
the warranty.
IMPORTANT NOTICE
Attention Installer: This manual contains important information about the installation, operation and safe use of this
product. This information should be given to the owner and/ or operator of this equipment.
WARRANTY COVERAGE
Please refer to www.oceanled.com/warranty for full warranty statement.
This manual contains important information about the installation, operation, and safe use of this product.
This information should be given to the owner and/ or operator of this equipment.

SPORTS SERIES Single / Dual / Colours / DMX.
INSTALL & OPERATION MANUAL
3
Contents
Preface .............................................................................................................................................................................. 1
1 Installation Checklist....................................................................................................................................................... 4
2 Overview......................................................................................................................................................................... 5
3 Installation....................................................................................................................................................................... 7
3.1 Preparing The Hull................................................................................................................................................... 7
3.2 Installing The Light Fixture ...................................................................................................................................... 8
3.3 Electrical Installation (12/24V DC)......................................................................................................................... 10
3.4 Control System Installation.................................................................................................................................... 16
3.5 Finalising The Installation...................................................................................................................................... 17
3.6 Test Your Installation............................................................................................................................................. 17
4 Operation / Maintenance.............................................................................................................................................. 18
4.1 Single Colour Strobe ............................................................................................................................................. 18
4.2 Dual Colour Operation........................................................................................................................................... 18
4.3 Sport Dual Colour Configuration Mode................................................................................................................. 18
4.4 Sport Multi Colour / Colours DMX - Control With DC Switch Operation .............................................................. 19
4.5 DMX Control .......................................................................................................................................................... 19
4.6 Maintenance .......................................................................................................................................................... 20
4.7 Replacement Parts ................................................................................................................................................ 20
5 Troubleshooting............................................................................................................................................................ 21
5.1 Troubleshooting Problems And Their Solutions ................................................................................................... 21
6 Appendix....................................................................................................................................................................... 24
6.1 Overall Dimensions ............................................................................................................................................... 24
6.2 accessories............................................................................................................................................................ 25
6.3 Cable Gauge Chart 12V........................................................................................................................................ 26
6.4 Cable Gauge Chart 24V........................................................................................................................................ 27
6.5 How To Use Cable Guage Chart .......................................................................................................................... 28
6.6 Installation Of 2-Way DMX Junction Box.............................................................................................................. 29
7 Warranty ....................................................................................................................................................................... 31

SPORTS SERIES Single / Dual / Colours / DMX.
INSTALL & OPERATION MANUAL
4
1 Installation Checklist
1. Decide on light spacing –OceanLED recommendations available. Ensure mounting location is flat and check
internally for ease of access if there is a rib, strut or other hull structure that may interfere with the installation.
Avoid mounting lights on surfaces that are subjected to high speed water impact e.g., planing surfaces. If
positioning lights on a transom, take into consideration swim platforms and obstacles that may block the
initial portion of the light.
2. Electrical wiring - Selecting the correct cable gauge is crucial for safe and efficient electrical wiring. Referring
to a cable gauge chart helps determine the appropriate wire diameter based on the expected current load
and other factors. By using the right gauge, the risk of overheating, voltage drops, and other electrical issues
can be minimized, ensuring the overall reliability and safety of the electrical system. Ensure correct cable
gauge is used (refer to relevant cable gauge chart in the appendix of this manual).
3. Control system chosen - There are various options available, including switch and DMX control. Switch
control involves using simple switches to manually turn on or off the lights. DMX control, such as the
OceanLED or third-party controllers, provides a more sophisticated solution. DMX control allows for
centralized and programmable control of multiple devices, enabling advanced lighting effects, colour
changes, and synchronization. These systems offer enhanced flexibility, scalability, and customization
options, making them ideal for complex lighting installations.
4. Preparing the hull. Please follow the manufacturer's instructions and guidelines for preparing the hull and
installing the lights to ensure a safe and effective installation process.
5. Correct marine sealant applied evenly around the cable and around the perimeter of the light unit.
6. Correct hardware used for fixing of light fixture onto hull (marine grade stainless steel screws provided).
When installing sport lights, it is essential to follow the manufacturer's instructions and recommendations.
This includes properly sealing and waterproofing the installation area to maintain the integrity of the hull and
prevent any potential water damage. Adhering to these guidelines will help ensure the lights perform
optimally and maintain the longevity of the hull.
7. Waterproof connections: When installing electrical components, such as underwater lights, in a marine
environment, it's crucial to use waterproof connections. These connections are designed to prevent water
from entering, which can lead to corrosion, electrical shorts, and other issues. Waterproof cable connectors,
butt splices with glue-lined heat shrink, and junction boxes are commonly used to create reliable and
watertight seals at connection points. These measures safeguard the electrical wiring, ensuring its durability
and protecting the overall system from water damage.
8. Test installation BEFORE entering water. Never connect/ disconnect lights whilst powered ON. When
installing underwater lights on a hull, it is crucial to thoroughly test the installation before immersing the
vessel in water. This step ensures that everything is functioning correctly and minimizes the risk of any
potential issues or complications.
9. Troubleshooting if required - If any issues arise during or after the installation of underwater lights, it is
important to troubleshoot them promptly. By following the guidelines provided by the manufacturer, most
problems can be resolved. Common troubleshooting steps may include checking electrical connections,
inspecting wiring for damage and verifying power supply. Prompt troubleshooting helps identify and resolve
issues, ensuring the optimal performance of the lights.