OHAUS TD52 User manual

TD52 Indicator
USB Host Option
(For Wireless Communication Option)
Instruction Manual
Interfaz de host USB
(Para conexiones inalámbricas)
Manual de instrucciones
Interface hôte USB
(Pour connexion sans fil)
Manuel d’instruction
USB Host-Schnittstelle
(für drahtlose Verbindung)
Bedienungsanleitung
Interfaccia Host USB
(Per collegamento wireless)
Manuale di Istruzioni
USB ⃊
⃊幍⮖折ↅ
᧤䞷ℝ㡯兎扭㘴᧥
∎䞷広㢝󱂖

EN-1
INTRODUCTION
This Interface Kit is for use with Ohaus TD52 products and Wi-Fi dongle.
KIT CONTENTS
INTERFACE INSTALLATION
For TD52P version
1. Separate the indicator from the base by loosening load cell cable male connector.
Remove the Interface option cover.
Load cell cable male connector
Interface option cover

EN-2
2. Break off the rib of the interface option cover as shown.
3. Connect the 9 pin USB Host Board cable to the main board connector.
4. Install the USB Host board. Secure it with the 2 screws.
Cable
Main board
connector
Rib

EN-3
5. Connect the USB Host cable to the 9 Pin connector on the option board.
6. Plug the USB donglein and put theinterface option cover back on the terminal.
Screw
9 Pin
connector
USB Dongle

EN-4
For TD52XW version:
1. Remove the 6 sealing screws to open the rear housing. Remove the M25 hole plug as
shown.
2. Rotate the rear housing down away from the front housing as shown.
Screw
M25 hole plug
Load cell cable male
connector

EN-5
3. Connect 9 pin USB Host Board cable to the main board connector.
4. Install the USB host board. Secure it with 2 screws. (Note: Boss Post is 2 and 4.)
Cable
Main board connector
Boss Post 2, 4

EN-6
5. Connect the USB Host cable to the 9 Pin connector on the option board.
6. Put the rear housing back on the front housing. Fasten 6 screws with sealed washer. Plug
the USB Dongle through M25 hole.
7. Fasten the USB dongle cover.
Screw
9 Pin connector
USB Dongle
USB dongle cover

EN-7
For TD52XW with reversed rear cover:
1. Remove the 6 sealing screws to open the rear housing. Remove the M25 hole plug as
shown.
2. Rotate the rear housing down away from the front housing as shown.
Screw
Load cell cable connector
M25 hole plug

EN-8
3. Connect the USB Host cable to the main board connector.
4. Install the USB host board. Secure it with 2 screws. (Note: Boss Post is 1, 3)
Cable
Main board
connector
Boss post 1, 3

EN-9
5. Connect the USB Host cable to the 9 Pin connector on the option board.
6. Put the rear housing back on the front housing. Re-install the 6 screws. Plug the USB
dongle through the M25 hole (Note: the OHAUS logo faces up).
7. Fasten the USB dongle cover by the M25 hole.
Screw
9 Pin connector
USB Dongle
USB dongle cover

EN-10
SETUP & OPERATION
Upon installation of the interface, the indicator will recognize the USB Host InterfaceǃWi-Fi dongle
and add relevant items to the menu.
WIFI CONFIGURATION
Communication Options (bold is default, Red is read only)
Wi-
Fi
Configuration
MAC Address
00-11-22-33-44-55
Search
DHCP Client
On, Off
IP Address
192.168.1.100
Subnet Mask
255.255.255.255
Gateway
192.168.1.1
Port
6060
Alt Pirnt CMD
'a' ~ 'z', 'A' ~ 'Z', P
Alt Tare CMD
'a' ~ 'z', 'A' ~ 'Z', T
Alt Zero CMD
'a' ~ 'z', 'A' ~ 'Z', Z
Reset
No/Yes

EN-11
Communication Options (bold is default, Red is read only)
Print Setup
Assignment
Demand
Stable Only
Off, On (LFT Force On)
Auto On Stable
Mode
Load, Load and Zero
Auto On Accept
Interval
Time
1~50000
MT-Continuous
OH-Continuous
SICS
Select Template
Simple, Custom 1, Custom 2, Custom 3, Custom 4,
Custom 5
Edit Template
Field 1~ field 100
Edit String
String 1~ String 10
Reset
No/Yes
MAC Address
The Medium Access Control (MAC) Address of the wireless dongle is not editable.
Search
Select the Search submenu and press
the soft key corresponding to the icon
to
search for the Wireless
Access Point (AP).
The search result will last fora few
seconds.
Select an AP, and press the soft key
corresponding to the icon
to
connect to the AP.

EN-12
If the password is needed, enter the
password by using numeric keys.
Connect successfully.
DHCP Client
The DHCP (Dynamic Host Configuration Protocol) client can be Off or On. If the DHCP Client
setting is On, the IP Address, Subnet Mask, and Gateway fields are assigned automatically by the
network and they are read-only. If the DHCP Client is Off, the IP address, Subnet Mask and
Gateway must be assigned manually.
IP Address
IP Address is 192.168.1.100 by default.
Subnet Mask
Subnet mask is 255.255.255.0 by default.
Gateway
Gateway is 192.168.1.1 by default.
Port
There is a TCP server with the default port of 6060.
NOTE: The submenu will display after the installation of wireless dongle.

EN-13
COMPLIANCE
Mark
Standard
This product complies with the applicable harmonized standards of EU Directives
2011/65/EU (RoHS) and 2014/30/EU (EMC). The EU Declaration of Conformity is
available online at www.ohaus.com/ce.
FCC Note
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
Industry Canada Note
This Class A digital apparatus complies with Canadian ICES-003
Disposal
In conformance with the European Directive 2012/19/EU on Waste Electrical and
Electronic Equipment (WEEE) this device may not be disposed of in domestic waste.
This also applies to countries outside the EU, p
er their specific requirements.
Please dispose of this product in accordance with local regulations at the collecting
point specified for electrical and electronic equipment. If you have any ques
tions,
please contact the responsible authority or the distributor from which you purchased
this device.
Should this device be passed on to other parties (for private or professional use), the
content of this regulation must also be related.
For disposal i
nstructions in Europe, refer to www.ohaus.com/weee.
Thank you for your contribution to environmental protection.

ES-1
INTRODUCCIÓN
Este kit de interfaz se utiliza con el dongle wifi y los productos TD52 de Ohaus.
CONTENIDO DEL KIT
INSTALACIÓN DE LA INTERFAZ
Para la versión TD52P
1. Separe el indicador de la base aflojando el conector del cable macho para la
celda de carga. Retire la cubierta de la interfaz.
Cubierta de la interfaz
conector macho del cable de la celda de
carga

ES-2
2. Cortarla lengüeta de la cubierta de la interfaz, como se muestra.
3. Conectar el cable al conector de la placa principal.
4. Instalar la placa host USB. Fijarlo por mediación de los 2 tornillos.
5. Conectar el cable al conector de 9 pines de la batería de Litio.
Lengüeta
Cable
Conector de la placa
principal
Tornillo
Conector de 9
pines

ES-3
6. Conectar el dongle USB y colocar la cubierta trasera de la interfaz en el dispositivo.
Para la versión TD52XW:
1. Quitar los 6 tornillos de sellado para abrir la carcasa trasera. Retirar el tapón M25, como se
muestra.
Tornillo
Tapón M25
conector macho del cable
de la celda de carga
Dongle USB

ES-4
2. Separar la carcasa trasera de la carcasa frontal como se muestra.
3. Conectar el cable al conector de la placa principal.
Cable
Conector de la placa
principal