OHAUS TD52 User manual

TD52 Indicator
USB Host Option
(For Wireless Communication Option)
Instruction Manual
Interfaz de host USB
(Para conexiones inalá mbricas)
Manual de instrucciones
Interface hô te USB
(Pour connexion sans fil)
Manuel d’instruction
USB Host-Schnittstelle
(fü r drahtlose Verbindung)
Bedienungsanleitung
Interfaccia Host USB
(Per collegamento wireless)
Manuale di Istruzioni
Opcjonalny Port USB Host
(Umożliwia podłączenie dongla WiFi, pamięci USB, skanera kodów kreskowych)
Instrukcja Obsługi
USB ホスト インターフェイス
取扱説明書
USB Host Option
(For Wireless Communication Option)
사용 설명서
USB 主设备选件
（用于无线连接）
使用说明书

EN-1
INTRODUCTION
This Interface Kit is for use with Ohaus TD52 products.
KIT CONTENTS
INTERFACE INSTALLATION
For TD52P version
1. Separate the indicator from the base by loosening load cell cable male connector.
Remove the Interface option cover.
Load cell cable male connector
Interface option cover

EN-2
2. Break off the rib of the interface option cover as shown.
3. Connect the 9 pin USB Host Board Cable to the main board connector.
4. Install the USB Host Board. Secure it with the 2 screws.
Cable
Main board
connector
Rib
Boss Post 2, 4

EN-3
5. Connect the USB Host Cable to the 9 Pin connector on the option board.
6. Plug the USB Flash Drive, the Barcode Scanner or the RFID device in and put the interface
optional cover back to the indicator. To use the USB Flash Drive, we recommend to use
the USB storage capacity less than or equal to 32G and the size of the drive within 60mm x
22mm x 12mm.
Bolts
9 Pin
connector
USB Flash Disk,
Barcode Scanner or
RFID
or RFID

EN-4
For TD52XW version:
1. Remove the 6 sealing screws to open the rear housing. Remove the M25 hole plug as
shown.
2. Rotate the rear housing down away from the front housing as shown.
Bolts
M25 hole plug
Load cell cable male
connector

EN-5
3. Connect 9 pin USB Host Board Cable to the main board connector.
4. Install the USB Host Board. Secure it with 2 screws. (Note: Boss Post is 2 and 4.)
Cable
Main board connector
Boss Post 2, 4

EN-6
5. Connect the USB Host Cable to the 9 Pin connector on the option board.
6. Put the rear housing back to the front housing. Fasten 6 screws bolts (Torque is
1.8N*m± 0.5). If you insert a USB flash drive, plug in the USB Flash Drive, through M25
hole.
Screw
9 Pin connector
USB Flash Drive

EN-7
7. Fasten the USB Device Cover if you are using a USB Flash Drive
8. If you insert a Barcode Scanner or RFID cable, disassemble the cable gland by loosening the
cap nut and removing the rubber seal. Pass the cable through the cap nut; then spread the
rubber seal and place it over the cable. Now pass the cable through the body of the cable gland.
9. Put the rear housing back tn the front housing. Install the 6 sealing screws (Torque is
1.8N*m± 0.5). Insert the above cable through the housing and connect it to the board.
USB Peripheral Cover
Barcode Scanner cable
or RFID cable
M25 Cable gland
Cap nut
M25 Hole

EN-8
10. Install the body of the cable gland into the rear housing. Tighten the cable gland.
11. Push the rubber seal into the body of the cable gland.
12. Fasten the Cover of M25 Gland.
Cable gland
Rubber seal
The Cover of M25 Gland