OHAUS Scout pro Installation guide

Scout Pro FAQ
AppNotes.v20170811_ AG
For any further questions, please e-mail us at [e-mail], or call us at 973-377-9000 #2 or ext. 7852 from 8AM to 5PM EST
Topic:
This list compiles frequently asked questions about the Scout Pro:
a) How do I turn on the units of measure
b) How do I switch between units of measure
c) How do I calibrate my unit
How to Turn On Units of Measure
Enabling or disabling the units of measure can be accomplished in the UNITS menu.
You can also click here for the user manual -- refer to Section 3: Operations, pages EN-11 (navigating the
main menu) and EN-13 (entering the UNIT menu).
Note1: during MENU navigation, use the following
buttons to initiate selections YES or NO.
Note2: depending on the region,the [ON/ZERO
Off] button may be designated as [ON/ 0/T Off].
1. With the scale (and lock switch) OFF: press
and hold [ON/ZERO Off] (approx. 5 seconds)
until the scale flashes MENU.
2. Release the button once MENU is displayed
After releasing the button, the scale will
display CAL.
3. Press [PRINT Unit] repeatedly until UNIT is
displayed.
4. Once UNIT is displayed, press [ON/ZERO Off]
to select this menu.
YES
NO
. . .

Scout Pro FAQ
AppNotes.v20170811_ AG
For any further questions, please e-mail us at [e-mail], or call us at 973-377-9000 #2 or ext. 7852 from 8AM to 5PM EST
5. Press [PRINT Unit] repeatedly to cycle
through available units of measure.
6. In this example, you want to turn on grams:
Once "g" is displayed, press [ON/ZERO Off]
to select this unit of measure.
7. The current setting is displayed flashing (in
this case: OFF).
Press [PRINT Unit] until "ON" is displayed.
8. Once "ON" is displayed, press [ON/ZERO
Off] to select this setting.
Grams is now turned on and available when
you switch through units of measure during
operations.
9. To exit from the menu and return to
operations:
Press [ON/ZERO Off] again to revert to the
UNIT menu.
10. When UNIT is displayed, press [PRINT Unit]
until END is displayed.
11. Once END is displayed, press [ON/ZERO
Off] to exit from the menu and return to
operations.

Scout Pro FAQ
AppNotes.v20170811_ AG
For any further questions, please e-mail us at [e-mail], or call us at 973-377-9000 #2 or ext. 7852 from 8AM to 5PM EST
How to Switch Between Units of Measure
Long-press [PRINT Unit] to scroll through the enabled units of measure.
If the desired unit of measure is not displayed, make sure it is enabled in the UNITS Menu (see previous
section: How to turn on units of measure).
Press and hold [PRINT Unit] to scroll through the
enabled units of measure.
In this example, the scale is scrolling through
grams and ounces.
Release the button once the desired unit of
measure is displayed.
In this example, grams ("g").
Hint:
For OHAUS products, the second line on the
button generally means a secondary function that
is activated with a long-press.
. . .
. . .
Long-press

Scout Pro FAQ
AppNotes.v20170811_ AG
For any further questions, please e-mail us at [e-mail], or call us at 973-377-9000 #2 or ext. 7852 from 8AM to 5PM EST
How to Calibrate
The Scout Pro has two methods of calibration: Span and Linearity. Following is a quick guide on how to
perform a Span calibration.
You can also click here for the user manual -- refer to Section 3: Operations, pages EN-14 and EN-15
(Calibration).
Span calibration uses two calibration points: zero and a specified calibration weight (usually full scale
capacity). Before beginning calibration, make sure the Lock Switch is off, and you have the appropriate
calibration masses.
1. With the scale (and lock switch) OFF: press
and hold [ON/ZERO Off] (approx. 5 seconds)
until the scale flashes MENU.
2. Release the button once MENU is displayed
After releasing the button, the scale will
subsequently display CAL.
Make sure the pan is empty.
3. Press [ON/ZERO Off] to initiate Span
calibration.
4. "-C-" is displayed while the scale is acquiring
the zero value.
5. After establishing the zero point, the second
calibration value is displayed (in this
example, 200g).
. . .

Scout Pro FAQ
AppNotes.v20170811_ AG
For any further questions, please e-mail us at [e-mail], or call us at 973-377-9000 #2 or ext. 7852 from 8AM to 5PM EST
6. Place the requested calibration mass on the
pan, then press [ON/ZERO Off].
7. "-C-" is displayed while the scale is acquiring
the second value.
After establishing the second calibration
point, "DONE" is displayed.
Then the value of the calibration mass is
displayed.
The scale is now calibrated and ready for
operations.
8. Remove the calibration mass, and the scale
will return to zero.