Ohlins YA 469 User manual

Shock absorber for Yamaha R6
YA 469
Mounting Instructions
Note!1
Please note that there can be small differences
between your product and the images in
these instructions.
Note!1
Please note that during storage and transport,
especially at high ambient temperature, some
of the oil and grease used for assembly may
leak and stain the packaging. This will not
cause damage to the product, wipe off the
excessive oil or grease with a cloth.
Note!1
Before you install this product, check the kit
contents. If anything is missing, please contact
an Öhlins dealer.
Warning!⚠
Before you install this product, read the Öhlins
Owner’s manual. This product is an important
part of the vehicle and the vehicle stability.
Kit Contents
Description Part No Pcs
Shock absorber YA469 1
Sticker Memo notes 01180-01 1
Sticker set Öhlins 1
Owner’s manual 07242-07 1

2
1
Put the motorcycle on a work stand so that the
rear wheel barely touches the ground.
2
Remove the seat and the tank side panel.
3
Remove the screws on the tank, one in the
front and one on each side.
4
Pivot the tank and loosen the upper attachment
nut of the original shock absorber.
5
Remove the screw that attaches the pull rods
to the swing arm. Remove the lower shock
absorber attachment.
6
Remove the upper attachment of the original
shock absorber. Remove the original shock
absorber.
7
Remove the original spacer between the upper
shock attachment and the frame.
MOUNTING INSTRUCTIONS
Warning!⚠
We strongly recommend to let an Öhlins dealer
install this product.
Warning!⚠
If you work with a lifted vehicle, make sure that it
is safely supported to prevent it from tipping over.
Note!1
When you work with this product, see the
vehicle service manual for vehicle specic
procedures and important data.
Note!1
Before you install this product clean the vehicle.
8
Use the original screws and install the Öhlins
shock absorber in the same position as the
original shock absorber.
9
Install the tank, side cover and the seat. Install
all removed parts in the same positions as they
were before removal.
Note!1
Lower the vehicle so that the suspension
is slightly compressed before you tighten
the screws.
Caution!✋
Make sure that you tighten all screws to the
correct torque and that nothing fouls or restricts
movement of the shock absorber/front fork/
steering damper when the suspension is fully
compressed or extended.

3
MOUNTING INSTRUCTIONS
2
3
4
5

Öhlins Racing AB
Box 722
S-194 27 Upplands Väsby, Sweden
Phone [phone]
fax [phone]
© Öhlins Racing AB. All rights
reserved. Any reprinting or
unauthorized use without the written
permission of Öhlins Racing AB
is prohibited.
Öhlins products are subject to
continuous improvement and
development, therefore, although
these instructions include the most
up-to-date information available at
the time of printing, minor updates
may occur.
To nd the latest information
contact an Öhlins distributor.
Please contact Öhlins if you have
any questions regarding the
contents in this document.
SETUP DATA
Spring
preload
adjuster
Length
adjuster
Compression
damping
adjuster
Rebound
damping
adjuster
Warning!⚠
Before you ride/drive, always make sure that the
setup is according to the recommended setup
data. Read about adjustments and setting up
in the Öhlins Owner’s Manual before you make
any adjustments. Contact an Öhlins dealer if
you have any questions about setting up.
ADJUSTMENTS
Part no. MI_YA469_0
Issued 2017-11-01
Length 293 +5/-1 mm
Stroke 60 mm
Rebound 14 clicks
Compression 14 clicks
Spring preload 14 mm
Spring 21041-29
Spring rate 90 N/mm
Spring free length 150 mm
Recommended sag and ride height
R1-R3 28 mm
F1-F3 38 mm