Ohlins FSK 105 User manual

Fork Spring Kit for Honda CB650F & CBR650F
FSK 105
Mounting Instructions
Note!
Please note that this image is a general representation
of the product and may differ slightly from your product.
Note!
Please note that during storage and transportation,
especially at high ambient temperature, some of the oil
and grease used for assembling may leak and stain the
packaging. This is in no way detrimental to the product,
wipe off the excessive oil/grease with a cloth.
Note!
Before installing this product, check the contents of the
kit. If anything is missing, please contact an Öhlins dealer
.
Warning!
After you have installed this product, take a test ride at
low speed to be sure that your vehicle has maintained
stability.
Kit Contents
Description Part No Pcs
Top cap assembly 2
Preload tube 60060-05 2
Spring 68008-75 2
Washer 04752-03 2
Sticker Öhlins white 01185-01 2
Sticker Öhlins blue 00192-01 2
Warning!
Öhlins cannot be held responsible for any personal
injury or damage that may occur after installing the
Öhlins spring kit. We strongly recommend to let an
Öhlins authorized service center to install this kit.

2
MOUNTING INSTRUCTIONS
1
2
3
4
Original Front Fork assembly

3
MOUNTING INSTRUCTIONS
60206-02
60005-13
04722-14 60051-03
05258-06
5 : 04752-03
6 : Top cap assembly
7 : 60060-05
8 : 68008-75
5
Öhlins Front Fork kit assembly
00638-92

Öhlins Racing AB
Box 722
SE-194 27 Upplands Väsby,
Sweden Phone [phone]
fax [phone]
© Öhlins Racing AB. All rights
reserved. Any reprinting or
unauthorized use without the written
permission of Öhlins Racing AB
is prohibited.
Öhlins products are subject to
continuous improvement and
development, therefore, although
these instructions include the most
up-to-date information available at
the time of printing, minor updates
may occur.
To nd the latest information
contact an Öhlins distributor.
Please contact Öhlins if you have
any questions regarding the
contents in this document.
Part no. MI_FSK105_EN_0
Issued 2015-07-01
MOUNTING INSTRUCTIONS
Congratulations!
With this purchase you have made a clear
statement. This high performance Front Fork
spring kit from Öhlins is nothing but pure racing
breed which means that you have taken one
more step to eliminate luck on your motorcycle.
The balance between your Front Fork and
rear suspension will sharpen up and the
performance of your Front Fork will improve.
Almost 40 years of racing experience is now a
crucial part of your riding experience.
Recommended oil
We recommended to use Öhlins high performance
Front Fork uid 01316-01.
Recommended oil Level
140mm.
How to install
1.Put the motorcycle on the work stand so that
the front wheel barely touch the ground. Make
sure the motorcycle is in a stable position.
2.Release the fork tube from the top triple clamp.
3.Remove the original Top cap (1), Pre-load tube
(2), and Spring (3)
4.Insert the Öhlins spring (8), Spring washer (5),
Öhlins Pre-load tube (7)
5.Install the Öhlins Top cap assembly. Tighten
the top cap at torque value  10N/mm.
Note!
The measurement of oil level is taken from the top of the
inner tube (5) to the oil surface.
> The fork leg need to be in vertical position
> The fork need to be fully compressed
> The fork must be without the spring and the preload
tube
Note!
Öhlins FSK 105 gives the possibility to adjust the spring
preload -5/+15mm from standard preload (13mm).
> Every complete turn equal 1mm adjustment
Note!
Öhlins FSK 105 spring 68008-75 rate is 7.5N/mm