Oki B6100n Original instructions

Warranty, Regulatory, and Safety Information
Oki Data Americas, Inc. (Oki Data) warrants this printer to be
free from defect in material and workmanship and will remedy
any such defect according to the terms of this Limited Warranty.
This Limited Warranty extends to the original purchaser only.
This Limited Warranty does not extend to consumable items.
Oki Data will repair (or at its option, replace) at no charge, any
defective component(s) for one (1) year on site from the date of
purchase (U.S. and Canada only—see details below)
To make request or claim for service under this Limited
Warranty, contact your Oki Data Authorized Dealer, authorized
third-party service provider, or Oki Data.
A written receipt for the product, showing the date of purchase,
dealer’s name, and serial number of the printer, must accompany
any request or claim for work to be performed under this Limited
Warranty.
This Limited Warranty shall not apply if the product has been
damaged due to abuse, misuse, misapplication, accident, or as a
result of service or modification by any other than an authorized
Oki service center.
THERE ARE NO EXPRESS WARRANTIES OTHER THAN
THOSE ON THE FACE HEREOF AND DESCRIBED
ABOVE. NO WARRANTIES WHETHER EXPRESS OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY
IMPLIED WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE, SHALL
EXTEND BEYOND THE RESPECTIVE WARRANTY
PERIOD DESCRIBED ABOVE OF ONE (1) YEAR ON SITE.
Some states do not allow limitations on how long an implied
warranty lasts, so the above limitation may not apply to you.
OKI DATA SHALL NOT BE RESPONSIBLE OR LIABLE
FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES OR LOSS ARISING FROM THE USE OF THIS
PRODUCT. Some states do not allow the exclusion or limitation
of incidental or consequential damages, so the above exclusion
may not apply to you.
Additional information on obtaining service under this Limited
Warranty is available by contacting the Oki Data dealer from
whom the product was purchased, by contacting Oki Data
directly at 1-800-654-3282 (1-800-OKI-DATA) [U.S. and
Canada, English only] or at 1-856-222-7496 (Spanish only), or
by contacting one of the listed service locations.
This Limited Warranty applies to this Oki Data printer. However,
the procedure for obtaining service may vary outside the
continental United States. Contact your Oki Data dealer for such
warranty service information.
This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state.
On-Site Repair
Note: On-Site Repair is available in the United States and
Canada only. On-Site Repair does not include the
replacement or repair of product consumables or
supplies.
Oki Data will, for a period of one (1) year from the date of
original purchase, repair or replace (at Oki Data’s option) on-site
at the original purchaser’s facility and without charge, any
defective component(s) of the printer, provided that the warranty
service is performed by an Oki Data authorized service provider.
Oki Data reserves the right to use new and/or refurbished parts
for the warranty repair.
As a condition of this limited warranty, requests for On-Site
Repair must include the name and phone number of a fully
competent and responsible adult with the authority to consent to
the entry of the servicing technician to the premises where the
printer is located, and who will remain with the servicing
technician while the service work is performed. Any and all
dangerous conditions must be removed from the site prior to and
throughout the time a service technician is present. The service
technician may refrain from entering the premises or continuing
to provide services at any site, if in the servicing technician's
reasonable judgement the site poses a risk of physical harm or
danger. If warranty services cannot be performed or completed
due to any of the foregoing reasons the On-Site service option is
null and void and the product must be returned to an authorized
Oki Data service location for warranty repair service.
Service and Support: U.S. & Canada
Oki Data is firmly committed to the satisfaction of our
customers. If you have a problem that your customer
documentation cannot solve, contact the listed sources for
service or support.
Oki Data Service Providers: U.S. & Canada
For the most comprehensive, up-to-date listing of Oki Data
authorized Service Centers in the United States and Canada:
• In the U.S. go to www.okidata.com and click Dealer
Locator.
• In the U.S. and Canada, call 1-800-654-3282
(1-800-OKI-DATA).
Oki Data Contact Locations: U.S. & Canada
Sales and Service Dealers: U.S. & Canada
Consult the store location where you purchased your machine, or
contact Oki Data for the location of the nearest Authorized Oki
Data Service Dealer.
• Prices and minimum charges may vary.
• Proof of purchase is required for warranty work. Be sure to
retain your purchase documents.
Limited Warranty: U.S. & Canada
United States
Oki Data Americas, Inc.
2020 Bishops Gate Blvd.
Mt. Laurel, NJ 08054
Phone: [phone]
Fax: [phone]
Canada
Oki Data Americas, Inc.
2735 Matheson Blvd. East, Unit 1
Mississauga, Ontario
Canada L4W 4M8
Phone: [phone]
Fax: [phone]

2English
Telephone Support
Toll Free in the U.S. and Canada
Automated Attendant
1-800-654-3282 (1-800-OKI-DATA)
For quick answers to commonly-asked questions, the Automated
Attendant is available 24 hours a day, 7 days a week. The system
can provide immediate assistance with:
• Basic operating procedures
• Sales and service referrals
• Parts and consumable referrals
• Product information
Customer Support Professionals
1-800-654-3282 (1-800-OKI-DATA)
Customer Support Professionals are available 24 hours a day, 7
days a week. Please be sure that you are calling from a telephone
close to your machine so you can describe your problem
accurately.
Our Customer Support Professionals are trained on all current
OKI products. They can answer your questions regarding:
• Locations of sales and service dealers
• Installation of your machine
• Usage/normal maintenance of your machine
• Error message interpretation/solutions
• Parts and supplies identification
• Consumer relations
Note: Customer Support Representatives are not trained to
provide assistance with the use of commercial software
packages. Please consult your software user’s manual for
times and availability of their support.
Oki Data warrants this printer (hereinafter Product) to be free in
defect in material and workmanship and will remedy any such
defect according to the terms of this Limited Warranty. This
Limited Warranty does not extend to consumable items,
including but not limited to print cartridges, fuses, etc.
Oki Data will repair (or at its option, replace) at no charge, any
defective component(s) of the printer for a period of one (1) year
from the date of purchase.
This Limited Warranty extends to the original purchaser only.
To make a request or claim for service under this Limited
Warranty the original purchaser must return the Oki Data
Product to an Authorized Oki Data Service Center within the
country purchased. The purchaser returning the Product for
repair must pay for all transportation charges to the repair center.
A written receipt for the Product, showing the date of purchase,
dealer’s name, and both the model and serial numbers of the Oki
Data Product must accompany any request or claim for work to
be performed under this Limited Warranty.
This shall not apply if the Product has been damaged due to
abuse, misuse, misapplication, accident, or as a result of service
or modification by any other than an authorized Oki Data service
center.
THERE ARE NO EXPRESS WARRANTIES OTHER THAN
THOSE ON THE FACE HEREOF AND DESCRIBED
ABOVE. NO WARRANTIES EXPRESS OR APPLIED,
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE, SHALL EXTEND BEYOND
THE RESPECTIVE WARRANTY PERIOD DESCRIBED
ABOVE OF ONE (1) YEAR.
OKI DATA SHALL NOT BE RESPONSIBLE OR LIABLE
FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES OR LOSS ARISING FROM THE USE OF THIS
PRODUCT
.
Service and Support: Latin America
Oki Data Authorized Service Providers: Latin
America
For the most comprehensive, up-to-date listing of Oki Data
authorized Service Centers in Latin America:
• Consult our our web site www.okidata.com:
– Select your country or region under “Select Country/
Region.”
– Click ASSISTÊNCIA E SUPORTE (Brasil) or Soporte
(Mexico or Latin America).
• In Spanish-speaking countries, contact the Latin America
Service Coordinator at Oki Data’s Corporate Headquarters
at [phone] (Spanish only).
Oki Data Contact Locations, Latin America
If you are having a problem with your OKI product, please
contact any of the Authorized Service Centers shown for your
Country/Region on our Web site, www.okidata.com.
Sales and Service Centers: Latin America
If you need service, please contact the store where you bought
your OKI product or contact any of the Authorized Service
Centers shown for your Country/Region on our Web site for
information.
• Prices and charges may vary.
• A copy of the proof of purchase is required for the warranty
process.
Contacting Oki Data: Latin America
Information regarding our products and authorized service
centers is available in our Web site: www.okidata.com
Limited Warranty: Latin America
Mexico
Oki Data de Mexico, S.A. de C.V.
Rua Alexandre Dumas, No. 748-8
Col. Anzures, e.p. 11590
Mexico, DF
Phone: [phone]
Fax: [phone]
Brazil
Oki Data do Brasil, Ltda.
Mariano Escobedo 2220 - 80andar
Chácara Sto Antonio
São Paulo, SP Brazil 04717-004
Phone: [phone]
Fax: [phone]
Support Center: 0800-11-55-77
e-mail: [e-mail]

English 3
Customer Support Professionals: Latin America
Our customer support professionals are trained and certified on
all current OKI products. Make sure that you are close to your
printer when you call one of our OKI authorized service centers
so that you can describe your problem more accurately.
Customer support professionals can answer your questions
regarding:
• Location of nearest Authorized Service Center
• Installation of your machine
• Usage/normal maintenance of your machine
• Error message interpretation/solutions
• Parts and supplies identification
• Consumer relations
Product Identification and Use______________
B6100 Black Toner, P/N 52113701
For more information, contact Oki Data at 2000 Bishops Gate
Blvd., Mount Laurel, NJ, 08054-4620.
Emergency Information: Call 1-800-654-3282; US & Canada
Only
Hazardous Ingredients _____________________
Styrene/acrylate copolymer (55-60% by weight)
CAS#: Not available
Iron oxide (35-40% by weight)
CAS#: Not available
Polypropylene (less than 3% by weight)
CAS#: Not available
Amorphous silica (less than 1% by weight)
CAS#: Not available
Chromium/azo dye complex (less than 1% by weight)
CAS#: 84179-66-8, 10-125-50-0, 109125-51-1
Physical Data______________________________
Physical State: Solid
Melting/Freezing Point: Not available
Boiling Point: Not applicable
PH: Not available.
Vapor Pressure: Not applicable
Vapor Density (Air=1): Not available
Evaporation Rate (Butyl Acetate=1): Not available
Specific Gravity (H2O=1): Not available
Solubility in water: Negligible
Solubility in solvents: Not available
Coefficient of water/oil Distribution: Not available
Appearance and odor: Black powder, faint odor
Odor Threshold: Not available
Fire and Explosion Hazard Data _____________
Flammability: Not flammable under conditions of use.
Extinguishing Media: In case of fire, use extinguishing media
(water spray, foam, dry chemicals). When in a machine, treat as
an electrical fire.
Flash Point (OC): Not applicable
Lower Explosive Limit: Not applicable
Upper Explosive Limit: Not applicable
Auto-ignition Temperature: Not applicable
Hazardous Combustion Products: Not applicable
Explosion Data
Like most organic materials in powder form, it can form
explosive mixtures when dispersed in air.
Sensitivity to Mechanical Impact: Not available
Sensitivity to Static Discharge: Not available
Reactivity Data ____________________________
Stability: Stable
Conditions to Avoid: Not available
Polymerization: Not available
Hazardous Decomposition Products: Not available
Incompatibility: Not available
Toxicological Properties ____________________
Routes of Entry: Inhalation, Ingestion, Eyes, Skin
Effects of Acute Exposure: Practically non-toxic
Swallowed LD50 (rat): >5.0 g/kg1)
Skin LD50 (rabbit): >2.0 g/kg1)
Inhaled LC50 (rat): >5.0 mg/L/4hr1)
Effects of Chronic Exposure:
The results obtained from a sponsored, Chronic Toner Inhalation
Study, demonstrated no lung change in rats for the lowest (1 mg/
m3) exposure level (i.e. the level most relevant to potential
human exposure). A very slight degree of fibrosis was noted in
25% of the animals at the middle (4 mg/m3) exposure level,
while a slight degree of fibrosis was noted in all the animals at
the highest (16 mg/m3) exposure level. These findings are
attributed to "lung overloading", a generic response to excessive
amounts of any dust retained in the lungs for a prolonged period.
This study was conducted using a special test toner to comply
with EPA testing protocol. The test toner was ten times more
respirable than commercially available OKI toner, and would
not be functionally suitable for OKI equipment.1)
Exposure Limits:
ACGIH TLV (2002):
10 mg/m3(Total)
3 mg/m3(Respirable)
Irritancy: Not an irritant1)
Material Safety Data Sheet
MSDS#58358601

4English
Sensitization: Not a sensitizer1)
Carcinogenicity: Not classified as “Carcinogens”
IARC: No components are listed
NTP: No components are listed
OSHA: No components are listed
Reproductive Toxicity: Not classified as “Reproductive and
Development chemicals”
Teratogenicity: Not available
Mutagenicity: Ames Assay: Negative
Name of Toxicologically Synergistic products: Not available
1) This information is based on toxicity data for similar
materials and ingredients.
Preventive Measures _______________________
Personal Protective Equipment
Respiratory Protection: Not normally required. For large
spills, use dust respirator during cleanup.
Protective Gloves and/or Eye Protection: Not normally
required. For large spills, use rubber gloves and safety goggles
during cleanup.
Engineering Controls
Ventilation: Outside of normal ventilation, not normally
required.
Other Protective Equipment and/or Hygienic Practices:
None
Spill Cleanup
Small Spills
1 Remove sources of ignition.
2 Sweep up or soak up with a damp (cold water) cloth.
Large Spills
1 Remove sources of ignition.
2 Keep unnecessary and unprotected personnel away from
area.
3 Wear protective gear: respirator, rubber gloves, goggles.
4 Vacuum the spill, then wipe up remainder with a wet (cold
water) cloth.
5 Place waste material in a closed container.
Waste Disposal
• Prevent release of material into natural waters and sewers.
• Follow appropriate federal, state and local regulations.
• DO NOT incinerate toner or a print cartridge.
• DO NOT disassemble a print cartridge.
Precautions for Handling or Storage: Protect from the sun.
Store in a cool room, under 104°F (40°C).
Special Shipping Information: Non hazardous. Handle
container carefully to avoid shock. Do not drop. Keep dry.
Emergency First Aid Procedures _____________
Toner swallowed (ingested).
Immediately seek medical attention. Never give anything by
mouth to an unconscious person. If possible, rinse out mouth and
give one or two glasses of water or milk to drink.
Toner inhaled.
Remove person to fresh air. Seek medical attention.
Toner gets in the eyes.
Flush eyes with large quantities of cool water for 15 minutes,
keeping the eyelids open with fingers. If necessary, seek medical
attention.
Toner gets on the skin.
Wash toner off the skin with plenty of cool water and soap. If
necessary, seek medical attention.
Note: Small amounts of toner on skin or clothing can easily be
removed with soap and cold water. Hot water makes
toner harder to remove.
Preparation Date of MSDS __________________
Date: August 15, 2002
Prepared by:
Oki Data Americas, Inc.
Engineering Services Department
2000 Bishops Gate Blvd.
Mt. Laurel, NJ 08054-4620
Tel: [phone]
FAX: [phone]
http://www.okidata.com
my.okidata.com
Your printer has been carefully designed to give you years of
safe, reliable performance. As with all electrical equipment,
there are a few basic precautions you should take to avoid
hurting yourself or damaging the printer.
Safety Notes_______________________________
• Be sure to switch off and unplug the printer before
accessing the interior of the printer for cleaning,
maintenance, or fault clearance. Accessing the interior of a
live machine exposes you to the risk of electric shock.
• Do not place the printer in a hot, humid, dusty, or poorly
ventilated environment. Prolonged exposure to these
adverse conditions may cause fire or expose you to electric
shock.
• The printer is capable of operating normally within the
following environmental limits:
Temperature range: 41°F to 95°F (5°C to 35°C)
At high temperatures (95°F [35°C]), humidity should
be at or below 70%.
Humidity range: 15% to 85% (no condensation)
At maximum humidity (85%), temperature should be at
or below 82°F(28°C).
Safety Information

English 5
• Stop operation immediately if your printer produces smoke,
excessive heat, unusual noise, or smell. These conditions
can indicate or result in a fire. Immediately switch off and
unplug the printer, and contact your point of purchase.
• The fuser becomes very hot in normal operation. If a paper
jam has occurred, turn the power off and wait at least 10
minutes before removing the print cartridge and touching
the fuser section.
• Carefully read all setup and operating instructions. Be sure
to save all documents for future reference.
• Read and follow all warning and instruction labels on the
printer.
• Place your printer on a firm, solid surface. If you put it on
something unsteady, it might fall and be damaged.
• If you place it on a soft surface, such as a rug, sofa, or bed,
the vents may be blocked, causing the printer to overheat.
• The printer must be installed near a power outlet which will
remain easily accessible.
• Be certain that your power source matches the rating listed
on the back of the printer. If you aren’t sure, check with
your dealer or with your local power company.
• Your printer has a grounded, 3-prong plug as a safety
feature. It will only fit into a grounded outlet. If you can not
plug it in, you probably have an older, non-grounded outlet.
Contact an electrician to have it replaced with a grounded
outlet. Do not use an adapter to defeat the grounding.
• To avoid damaging the power cord, do not put anything on
it or place it where it will be walked on. If the cord becomes
damaged or frayed, replace it immediately.
• If you’re using an extension cord or power strip with the
printer, make sure that the total of the amperes required by
all the equipment on the extension is less than the
extension’s rating. Generally, the total ratings of all
equipment plugged into any one power line should not
exceed 15 amperes. Don’t exceed this unless you know that
the power line your equipment is plugged into has a rating
above 15 amperes.
• Unplug the printer before you clean it. Use only a damp
cloth. Do not use liquid or aerosol cleaners.
• To protect your printer from overheating, make sure no
openings on the printer are blocked. Do not put the printer
on or near a heat source, such as a radiator or heat register.
If you put the printer in any kind of enclosure, make sure it
is well ventilated.
• Do not use your printer near water. Do not spill liquid of
any kind into it.
• Do not poke anything into the ventilation slots on the
printer. You could get a shock or cause a fire.
• Aside from the routine maintenance described in the User’s
Guide, don’t try to service the printer yourself. Opening the
cover may expose you to shocks or other hazards. Don’t
make any adjustments other than those outlined in the
User’s Guide. You might cause damage requiring extensive
repair work.
• If anything happens that indicates that your printer is not
working properly or has been damaged, unplug it
immediately. Then, follow the procedures in “Service and
Support” for having your printer serviced.
These are some of the things to look for:
– The power cord or plug is frayed or damaged.
– Liquid has been spilled into the housing, or the printer
has been exposed to water.
– The printer has been dropped or its cabinet has been
damaged.
– The printer doesn’t function normally when you’re
following the operating instructions
.
ENERGY STAR®
As an ENERGY STAR Partner, Oki Data has determined that this
product meets the ENERGY STAR guidelines for energy
efficiency.
Year 2000 Compliance
This product is Year 2000 Compliant. It contains information
technology that accurately processes date and time data between
the years 1999 and 2000, and carries no issue for the September
9, 1999 (9999) programming concern. This product, when used
in combination with products purchased from other
manufacturers, whose products properly exchange data and time
information, will accurately process the date and time.
Federal Communications Commission
(FCC)
FCC Declaration of Conformity
1. Product Identification
Product Name: B6100
Model No.:
BXJA-7 (120 Volt)
BXJB-2 (230 Volt)
2. Statement
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2)
this device must accept any interference received, including
interference that may cause undesired operation.
3. Responsible Party
Oki Data Americas, Inc.
2000 Bishops Gate Boulevard
Mt. Laurel, NJ 08054-4620
1-800-654-3282 (1-800-OKI-DATA)
FCC Radio Frequency Interference Statement
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of FCC
rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to
operate the equipment.
Regulatory Information

© 2002 Oki Data Americas, Inc. 58359501
This equipment generates, uses, and can radiate radio frequency
energy. If the equipment is not installed and used in accordance
with the instructions, it may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause interference to radio or television
reception, which can be determined by turning the equipment off
and on, try to correct the interference using one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment and the reciever to outlets that are on
different circuits.
• Consult with the dealer or an experienced radio/television
technician to help.
• Always use the power cord provided with your machine.
When an extension cord is required, always use a properly
rated cord.
• In countries other than the United States, please contact your
point of purchase.
If your machine is a 220-240V model, there is no need to attach
a separate ground (earth) line since the ground (earth)
connection is incorporated in the power line. Plug it into a
properly rated outlet.
The use of a non-shielded interface cable with the reference
devices is prohibited. Shielded interface cables must not exceed
the following limitations:
• The length of the IEEE 1284 parallel interface cable must be
50 feet (15 meters) or less.
• The length of the Ethernet interface cable must be 328 feet
(100 meters) or less for type 10/100BASE-T or 185 meters
(607 feet) or less for type 10/BASE-2.
• The length of the power cord must be 10 feet (3 meters) or
less.
Industry Canada (IC)
IC Radio Interference Statement
This Oki Data apparatus complies with the Class B limits for
radio interference as specified in the IC Radio Interference
Regulations.
European Union Council of the European
Communities (EU)
EU Statement of Electromagnetic Conformance
This product complies with the requirements of the Council
Directive 89/336/EEC on the approximation of the laws of the
member states relating to electromagnetic compatibility.
EU Statement of Safety Conformance
This product is in conformity with Directive 73/23/EEC on the
harmonization of the laws of Member States relating to electrical
equipment designed for use within certain voltage limits.
Safety Compliance
Safety Standards
This product conforms the following safety standards:
UL1950
CSA C22.2 No. 950
EN 60950
IEC 950
73/23/EEC
Class 1 Laser Device and CDRH Compliance
This printer is certified as a Class 1 laser product under the U.S.
Department of Health and Human Services (DHHS) Radiation
Performance Standard according to the Radiation Control for
Health and Safety Act of 1968. This certification indicates that
the printer does not emit hazardous laser radiation. Since
radiation emitted inside the printer is completely confined within
the protective housings and external covers, the laser beam
cannot escape from the machine during any phase of user
operation.
The Center for Devices and Radiological Health (CDRH) of the
U.S. Food and Drug Administration implemented regulations for
laser products on August 1976. These regulations apply to laser
products marketed in the United States. The label on the printer
indicates compliance with the CDRH regulations and must be
attached to laser products marketed in the United States.
Other EMC Standards
This product also conforms to the following EMC standards:
• CNS 13438
•VCCIV-3/97.04
• AS/NZS 3548:1995 including A1:1997 and A2:1997
• EN55022: 1994 including A1:1995 and A2:1997
• FCC Part 15, Subpart B (CFR 47, 1995)
• CISPR22: 1993 including A1:1995 and A2:1996
Oki Data Americas, Inc., 2000 Bishops Gate Blvd., Mt. Laurel, NJ
08054-4620
Tel: [phone] FAX: [phone]
http://www.okidata.com my.okidata.com
Oki Data Americas, Inc., 2735 Matheson Blvd. East, Unit 1,
Mississauga, Ontario, Canada L4W 4M8
Tel: [phone] FAX: [phone]
Oki Data de Mexico, S.A. de C.V., Mariano Escobedo No. 748 - 8
Piso, Col Anzures, e. p. 11590, Mexico, DF
Tel: [phone] FAX: [phone]
Oki Data do Brasil, Ltda., Rua Alexandre Dumas, 2220 - 80andar,
Chacara Santo Antonio, 04717-004 São Paulo, SP Brazil ,
Phone: [phone] Fax: [phone]
Support Center: 0800-11-55-77
e-mail: okid[email protected]