Oki Okicolor8 User manual

Warranty, Regulatory
Information, and
Specifications
English

|OKICOLOR 82
Disclaimer
Every effort has been made to ensure that the information in
this document is complete, accurate, and up-to-date. Oki
Data assumes no responsibility for the results of errors or
omissions beyond its control. Oki Data also cannot
guarantee that changes in software and equipment made by
other manufacturers and referred to in this document will not
affect the applicability of the information in it. Mention of
software products manufactured by other companies does not
necessarily constitute endorsement by Oki Data.
Copyright Information
Copyright 1999 by Oki Data. All Rights Reserved
First Edition: September, 1999
Written and produced by the Oki Data Training and
Publications Department.
Contact Information
Please address any comments on this publication to:
MailingAddress
Oki DataAmericas, Inc.
Training and Publications Department
2000 Bishops Gate Boulevard
Mount Laurel, NJ 08054-4620
United States ofAmerica
e-MailAddress
[email protected]
WebSite
Please visit Oki Data’s multilingual web site at:
http://www.okidata.com
Trademark Information
OKI is a registered trademark of Oki Electric Industry
Company, Ltd.
OKICOLOR is a trademark of Oki Electric Industry Co., Ltd.
Energy Star is a registered trademark of the United State
Environmental Protection Agency.
Touch-Tone is a registered trademark of American Telephone
and Telegraph.
Windows is either a registered trademark or a trademark of
Microsoft Corporation in the United States and/or other
countries
ZIP Code is a registered trademark of the United States Postal
Service
Emergency First Aid Information
Refer to the Material Safety Data Sheet at the end of this
document.

Overview
|
Warranty, Regulatory Information, and Specifications: English 3
Contents
Year 2000 Compliance............................................ 4
Energy Star .............................................................. 4
Limited Warranty.................................................... 5
Limited Warranty—United States and Canada .............. 5
Limited Warranty—Latin America ................................. 8
Oki Data Depot Service Centers........................... 9
Authorized Service Providers ......................................... 9
Important Safety Information ............................. 11
Regulatory Information ....................................... 13
Specifications.......................................................... 16
Material Safety Data Sheets ................................ 18

|OKICOLOR 84
Year 2000
Compliance
All products currently sold by Oki Data are Year 2000
Compliant. Each product contains information technology
that accurately processes date and time data between the
years 1999 and 2000, and carries no issue for the September
9, 1999 (9999) programming concern. These products, when
used in combination with products purchased from other
manufacturers, whose products properly exchange data and
time information, will accurately process the date and time.
All future products are committed to meeting the same Year
2000 compliance.
Energy Star
As an Energy Star® Partner, Oki Data has determined that this
product meets the Energy Star guidelines for energy
efficiency.

Overview
|
Warranty, Regulatory Information, and Specifications: English 5
Limited Warranty
Limited Warranty—United States and
Canada
Oki DataAmericas, Inc. (Oki Data) warrants this printer to be
free from defect in material and workmanship and will
remedy any such defect according to the terms of this Limited
Warranty. This Limited Warranty extends to the original
purchaser only. This Limited Warranty does not extend to
network setup, application conflicts, or consumable items
including, but not limited to, image drum cartridges, toner
cartridges, fuses, etc.
Oki Data will repair (or at its option, replace) at no charge,
any defective component(s) of the Printer for one (1) year
from the date of purchase except for the printheads (LED
imaging arrays), which are warranted for a period of five (5)
years from date of purchase. This Limited Warranty extends
to the original purchaser only. This Limited Warranty does
not extend to consumable items.
Consumables are covered separately under individual
consumable warranties. Please refer to the appropriate
consumable item’s warranty for further information.
On-Site Repair
!On-Site Repair is available in the United States and Canada only. On-Site Repair does not include the
replacement or repair of product consumables or
supplies.
Oki Data will, for a period of one (1) year from the date of
purchase, repair (or replace at its option) on-site at the
original purchaser’s facility (in Canada, original purchaser’s
facility must be located within a 100 kilometers radius of an
Authorized Service Center) and without charge, any
defective component(s) of the printer, provided that this

|OKICOLOR 86
warranty service is performed by an authorized Oki Data
service center or authorized third-party service organization.
The printheads (LED imaging arrays) have a five (5) year
parts warranty from date of purchase. On-site replacement of
the printheads is limited to one year from date of purchase.
For the remaining printhead warranty period, replacement
will be at an authorized service center or authorized third
party service organization.
To make request or claim for service under this Limited
Warranty, contact your Oki Data Authorized Dealer,
authorized third-party service provider, or Oki Data.
Oki Data will attempt to fix the problem over the telephone
prior to scheduling an on-site visit. It will be the
responsibility of the owner to install any warranty
replacement consumable (drum or toner) or other end user
replaceable item as supplied by Oki Data.
A written receipt for the product, showing the date of
purchase, place of purchase, and both the model and serial
numbers of this printer must accompany any request or claim
for work to be performed under this Limited Warranty. In the
event a service request is verified by Oki Data over the
phone, a mailed or faxed copy of the written purchase receipt
is required to verify in-warranty coverage prior to scheduling
an on-site repair.
This Limited Warranty shall not apply if the product has been
damaged due to abuse, misuse, misapplication, accident, or
as a result of service or modification by any other than an
authorized Oki Data service center.
THEREARE NOEXPRESSWARRANTIESOTHERTHAN
THOSEONTHEFACEHEREOFANDDESCRIBEDABOVE.
NOWARRANTIES,WHETHEREXPRESS ORIMPLIED,
INCLUDING,BUTNOTLIMITEDTO,ANYIMPLIED
WARRANTIESOFMERCHANTABILITYORFITNESSFOR
APARTICULARPURPOSE,SHALLEXTENDBEYOND
THERESPECTIVEWARRANTYPERIODDESCRIBED
ABOVE. Some states do not allow limitations on how long
an implied warranty lasts, so the above limitation may not
apply to you.
OKIDATASHALLNOTBERESPONSIBLE ORLIABLE
FORANYSPECIAL,INCIDENTAL,ORCONSEQUENTIAL
DAMAGESORLOSSARISINGFROMTHEUSEOFTHIS
PRODUCT. Some states do not allow the exclusion or
limitation of incidental or consequential damages, so the
above limitation may not apply to you.

|
Warranty, Regulatory Information, and Specifications: English 7
Additional information on obtaining service under this
Limited Warranty is available by contacting the OKI DATA
dealer from whom the product was purchased, by contacting
Oki Data directly at 1-800-654-3282 (1-800-OKI-DATA),
United States and Canada, English and French only, or
1-856-222-5276 (Spanish only), or by contacting one of the
listed service locations.
This Limited Warranty applies to this Oki Data printer.
However, the procedure for obtaining service may vary
outside of the continental United States. Contact your Oki
Data dealer for such warranty service information.
This warranty gives you specific legal rights and you may
also have other rights, which vary from state to state.

|OKICOLOR 88
Limited Warranty—Latin America
Oki DataAmericas, Inc. (Oki Data) warrants this printer to be
free from defect in material and workmanship and will
remedy any such defect according to the terms of this Limited
Warranty. This Limited Warranty does not extend to network
setup, application conflicts, or consumable items including,
but not limited to, image drum cartridges, toner cartridges,
fuses, etc.
Consumables are covered separately under individual
consumable warranties. Please refer to the appropriate
consumable item’s warranty for further information.
Oki Data will repair (or at its option, replace) at no charge,
any defective component(s) of the Printer for one (1) year
from the date of purchase except for the printheads (LED
imaging arrays), which are warranted for a period of five (5)
years from date of purchase. This Limited Warranty extends
to the original purchaser only.
To make a request or claim for service under this Limited
Warranty, the original purchaser must return the Oki Data
Product to Oki Data or an authorized Oki Data service center
within the country purchased. The purchaser returning the
product for repair must pay for all transportation charges to
the repair center. A written receipt for the Product, showing
the date of purchase, dealer’s name, and both the model and
serial numbers of the Oki Data Product must accompany any
request or claim for work to be performed under this Limited
Warranty.
This Limited Warranty shall not apply if the product has been
damaged due to abuse, misuse, misapplication, accident, or
as a result of service or modification by any other than an
authorized Oki Data service center.
THEREARE NOEXPRESSWARRANTIESOTHERTHAN
THOSEONTHEFACEHEREOFANDDESCRIBEDABOVE.
NOWARRANTIESEXPRESSORAPPLIED,INCLUDING,
BUTNOTLIMITEDTO,ANYPARTICULARPURPOSE,
SHALLEXTENDBEYONDTHE RESPECTIVE
WARRANTYPERIODABOVE OF ONE(1)YEAR.

Overview
|
Warranty, Regulatory Information, and Specifications: English 9
Oki Data Depot
Service Centers
Authorized Service Providers
Oki Data has over 2,000 local Authorized Service Providers
in North and South America.
For the most comprehensive, up-to-date listing of Oki Data
authorized Service Centers:
• Consult our web site at www.okidata.com
• In the U.S. and Canada, call 1-800-654-3282
(1-800-OKI-DATA) English and French only.
• In LatinAmerica, contact the LatinAmerica Service
Coordinator at Oki Data’s Corporate Headquarters at
856-222-5276 (Spanish only).
United States
Oki DataAmericas, Inc.
2020 Bishops Gate Blvd.
Mt. Laurel, NJ 08054
Phone: [phone] (800-OKI-DATA)
U.S. and Canada, English and French only
[phone] (Latin America)
Fax: [phone] (U.S. and Canada)
856-222-5260 (Latin America)
Canada
Oki DataAmericas, Inc.
2735 Matheson Blvd. East, Unit 1
Mississauga, Ontario
Canada L4W 4M8
Phone: [phone] (800-OKI-DATA)
English and French only
Fax: [phone]

|OKICOLOR 810
Brazil
Oki Data do Brasil, Ltda.
Av. Leonardo da Vinci, 1178/1182
Jabaquara
Sao Paulo, Brazil
Phone: [phone]
Fax: [phone]
Mexico
Oki Data de Mexico, S.A. de C.V.
Av. Insurgentes 1700 – 7 Piso
Col. Florida 01030
Phone: [phone]
Fax: [phone]

Overview
|
Warranty, Regulatory Information, and Specifications: English 11
Important Safety
Information
Your Oki Data printer has been carefully designed to give
you years of safe, reliable performance.As with all electrical
equipment, there are a few basic precautions you should take
to avoid hurting yourself or damaging the printer.
• Carefully read the provided setup and operating
instructions.
• Save all provided documentation for future reference.
• Read and follow all warning and instruction labels on the
printer itself.
• Turn off the printer before opening printer covers or
replacing consumables.
• Unplug the printer before you clean it. Use only a damp
cloth; do not use liquid or aerosol cleaners.
• Place your printer on a firm, solid surface. If you put it on
something unsteady, it may fall and be damaged. If you
place it on a soft surface, such as a rug, sofa, or cushion,
the vents may be blocked, causing the printer to overheat.
• Protect your printer from overheating. Make sure no
obstructions block the openings of the printer. Do not put
the printer on or near a heat source (such as a radiator or
heat register). Keep the printer out of direct sunlight.
Allow enough room around the printer for adequate
ventilation and easy access to the paper trays. If you put
the printer in any kind of enclosure, make sure the
enclosure is properly ventilated.
• Do not use your printer near water. Do not spill liquid of
any kind into it.
• Be certain that your power source matches the rating listed
on the back of the printer. If you are not sure, check with
your dealer or with your local power company.
• Your printer has a grounded, three-prong plug as a safety
feature. This plug only fits into a grounded outlet. If the
plug does not fit, the outlet may be an older, non-
grounded type. Contact an electrician to have the outlet
replaced. Do not use an adapter to defeat the grounding.

|OKICOLOR 812
• Install the printer near an easily accessed power outlet.
• Avoid damaging the power cord. Do not put anything on
it or place it where it will be walked on. If the cord
becomes damaged or frayed, replace it immediately.
• If you are using an extension cord or power strip with the
printer, make sure that the total of the amperes required by
all the equipment on the extension is less than the
extension’s rating. The total ratings of all equipment
plugged into the outlet should not exceed 15 amperes.
• Do not poke anything into the ventilation slots of the
printer. You could get an electrical shock or cause
hazardous electrical arcing, which could cause a fire.
• Aside from the routine maintenance described in the
documentation, do not try to service the printer yourself.
Removing the cover may expose you to shocks or other
hazards.
• Do not make any adjustments other than those outlined in
the documentation. You may cause damage that will
require extensive repair work. The provided
documentation explains how to get your printer serviced
by qualified Oki Data technicians.
If anything happens that indicates that your printer is not
working properly or has been damaged, unplug it
immediately and follow the procedures in the provided
documentation for having your printer serviced.
Here are some of the things to look for.
• The power cord or plug is frayed or damaged.
• Liquid has been spilled into the printer, or the printer has
been exposed to water.
• The printer has been dropped, or the cabinet is damaged.
• The printer does not function normally when you are
following the operating instructions.

Overview
|
Warranty, Regulatory Information, and Specifications: English 13
Regulatory
Information
Federal Communications
Commission Radio Frequency
Interference Statement for 120-Volt
Models
WARNING: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the
receiver.
• Plug the unit into an outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/television
technician for help.
It is the responsibility of the user to obtain the required
shielded cable in order to ensure compliance of this
equipment with FCC regulations.
Changes or modifications not expressly approved by Oki
Data may void your authority to operate this device.

|OKICOLOR 814
Federal Communications
Commission Radio Frequency
Interference Statement for 230/240-
Volt Models
WARNING: This equipment has been tested and found to
comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in
a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct
the interference at his own expense.
It is the responsibility of the user to obtain the required
shielded cable in order to ensure compliance of this
equipment with FCC regulations.
Changes or modifications not expressly approved by Oki
Data may void your authority to operate this device.
Industry Canada Radio Interference
Statement for 120-Volt Models
This Oki Data apparatus complies with the Class B limits for
radio interference as specified in the Industry Canada Radio
Interference Regulations.
Industry Canada Radio Interference
Statement for 230/240-Volt Models
This Oki Data apparatus complies with the Class A limits for
radio interference as specified in the Industry Canada Radio
Interference Regulations.

|
Warranty, Regulatory Information, and Specifications: English 15
European Union Council of the
European Communities Statement of
Electromagnetic Conformance for
230/240-Volt Models
This product complies with the requirements of the council
Directive 89/336/EEC on the approximation of the laws of
the member states relating to electromagnetic compatibility.
European Union Council of the
European Communities Statement of
Safety Conformance for 230/240-
Volt Models
This product is in conformity with Directive 73/23/EEC on
the harmonization of the laws of Member States relating to
electrical equipment designed for use within certain voltage
limits.
Federal Communications
Commission Declaration of
Conformity for 120 Volt Models
1. Product Identification
OKICOLOR 8, model N31001A
2. Statement
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
3. Responsible Party
Oki DataAmericas, Inc.
2000 Bishops Gate Boulevard
Mt. Laurel, NJ 08054-4620
1-800-654-3282 (1-800-OKI-DATA)
United States and Canada, English and French Only

Overview
|OKICOLOR 816
Specifications
For additional specifications (including General, Physical,
Interface, Print Media, Fonts, and Commands) refer to the on-
line User’s Guide.
Electrical
Voltage
120 V: 120 VAC +5.5%, -15%
230 V: 230VAC +/- 10%
Frequency
50/60 Hz +/- 2%
Power
Idle
Approximately 70 W
Operating
Approximately 230 W
Peak
Approximately 980 W
Power Save Mode
Approximately 32 W

|
Warranty, Regulatory Information, and Specifications: English 17
Environmental
Temperature
Operating
Maximum Permissible
50 to 90° F
10 to 32° C
Best Color Print Quality
63 to 81° F
17 to 27° C
PowerOff
32 to 109° F
0 to 43° C
Storage(Packed)
14 to 109° F
-10 to 43° C
Humidity
Operating
Maximum Permissible
20 to 80% Relative Humidity
Best Color Print Quality
50 to 70% Relative Humidity
PowerOff
10 to 90% Relative Humidity
Storage(Packed)
10 to 90% Relative Humidity

Overview
|OKICOLOR 818
Material Safety Data
Sheet
No. 58334601
Applies to Black Toner, Type C1,
P/N 40370601 (1.8 K Yield) and
P/N 41012301 (3 K Yield)
Revised September, 1999
For more information, contact Oki Data at:
2000 Bishops Gate Blvd.
Mount Laurel, NJ 08054-4620
United States ofAmerica
Emergency Information
1-800-654-3282 (1-800-OKI-DATA)
United States and Canada, English and French only
Emergency First Aid Procedures
Toner gets on the skin
Wash with plenty of soap and cool water.
Toner swallowed (ingested)
Seek medical attention immediately.
Toner inhaled
Remove person to fresh air and seek medical attention. If
person is not breathing, give artificial respiration. If person’s
breathing is difficult, give oxygen.
Toner gets in the eyes
Flush eyes with large quantities of cool water for 15 minutes,
keeping the eyelids open with fingers. Seek medical
attention.
!Small amounts of toner on skin or clothing can easily be removed with soap and cold water (hot water makes
toner harder to remove).

|
Warranty, Regulatory Information, and Specifications: English 19
Hazardous Ingredients
CarbonBlack(4% byweight)
CAS# 1333-86-4
OSHATWA3.5 mg/m3
ACGIHTLV3.5 mg/m3
Physical Data
Melting Point: Not available
Softening Point: 122 to 129°C (252 to 264°F)
Boiling Point: Not applicable
Vapor Pressure: Not applicable
Vapor Density (Air=1): Not available
Evaporation Rate (ButylAcetate=1): Not applicable
SpecificGravity(H2O=1): 1.16
Solubility in water: Insoluble
Appearance and odor: Black fine powder, no odor
Fire and Explosion Hazard Data
Flash Point(Method Used): Not applicable
Flammable Limits
Lower Explosive Limit: Not known
Upper Explosive Limit: Not known
Extinguishing Media: CO2, Dry Chemical, or Foam
General Fire Hazards: Minimal fire hazard. Material is
self-extinguishing.
Special Fire Fighting Procedures: Not provided
Unusual Fire and Explosion Hazards: Not applicable

|OKICOLOR 820
Health Hazard Data
Routes of Entry: Inhalation, Ingestion, Eyes, Skin.
1 Carbon Black
Group 2B “Possible Carcinogen”; IARC
Evidence of development of lung tumors in rats receiving
chronic inhalation exposure to free carbon black at levels
that induce particle overload of the lung. Studies
performed in animal models other than rats have not
demonstrated an association between carbon black and
lung tumors. A two-year cancer bioassay using a typical
toner preparation containing carbon black demonstrated
no association between toner exposure and tumor
development in rats.
In a study in rats by chronic inhalation exposure to a
typical toner, a mild to moderate degree of lung fibrosis
was observed in 92% of the rats in the high concentration
(16 mg/m3) exposure group, a mild degree of fibrosis was
noted in 22% of the animals in the middle
(4 mg/m3) exposure group, and no pulmonary change was
reported in the lower (1 mg/m3) exposure group, the most
relevant level to potential human exposures.
Carbon black is designated hazardous according to OSHA
29 CFR 1910.1200.
Reactivity Data
Stability: Stable
Polymerization: Will not occur.
Hazardous Decomposition Products: Combustion or
decomposition will generate phenol derivatives, carbon
monoxide and carbon dioxide at temperatures over 300°C
(572°F).
Temperature: Not available
Incompatibility: Avoid exposure to strong oxidizers.