Olympus VISERA ELITE II User manual

VISERA ELITE II Quick Reference Guide
Disclaimer: Information provided in this guide is not exhaustive. Please refer to the complete Instructions For Use for each
item of equipment which should be thoroughlyread and understoodprior to handling, use and storage of the equipment.
Light SourceCamera HeadSwitch On
Switch on the camera system using the workstation master
switch which will then turn from white to green.
There is a secondary power switch on the transformer
under the workstation. This should remain switched on.
Insert the camera head into the camera processor,
ensuring the connector is the correct way up.
Connect the light guide cable to the output socket.
If required, turn the lamp off by pressing and holding the
lamp button.
Note: The “Lamp” status is stand-by when the light guide
connector of the endoscope or the light guide cable is not
connected to the output socket of the video system
centre while the lamp is turned ON.
Caution: Do not touch the endoscope’s distal end and light
guide connector while the examination lamp is lit up. The
endoscope becomes hot while the examination lamp is lit
up and could cause operator burns.
UP mark
Video connector
Electrical contacts
Video connector socket
UP mark
Video connector
The colour bars on the monitor will now be replaced with
an image from the camera head.
Output socket
Video connector socket
OT
V
Lamp
Lamp status
Issue 1
05/02/2021
KMF-08927
NCDR 02863

VISERA ELITE II Quick Reference Guide
Disclaimer: Information provided in this guide is not exhaustive. Please refer to the complete Instructions For Use for each
item of equipment which should be thoroughlyread and understoodprior to handling, use and storage of the equipment.
White BalancingWhite BalancingCamera Head
Once the camera head, telescope and light guide cable are
connected, a white balance must be performed.
Perform a white balance by surrounding the tip of the
telescope in a white swab, ensuring it is fully enclosed.
Press and hold the white balance button until ‘White
Balance Complete’ appears on the monitor.
The white balance status changes to completed.
Note: the optimal brightness for each user preset has
already been set so there is no need to make adjustments
to the levels.
Attach the camera head to the telescope by rotating the
endoscope mount as below.
Releasing the camera head mount secures the telescope
in place.
Rotate
Endoscope
lock ring
Eyepiece Endoscope mount
White balance
White balance status
Issue 1
05/02/2021
KMF-08927
NCDR 02863

VISERA ELITE II Quick Reference Guide
Disclaimer: Information provided in this guide is not exhaustive. Please refer to the complete Instructions For Use for each
item of equipment which should be thoroughlyread and understoodprior to handling, use and storage of the equipment.
TroubleshootingCamera HeadCamera Head
Adjust the image magnification and focus using either the
rings on the non-autoclavable version or buttons on the
autoclavable version.
There are three programmable buttons on the camera head.
To check what they are programmed to do press ‘info’ and
then scope information on the processor.
When each button is pressed its function will light up but the
screen needs to be closed before it will perform the function.
Non-autoclavable
Focus Ring
Zoom Ring
Autoclavable
Focus buttons
Zoom buttons
W - decreases
T - increases
No power
• Ensure everything is switched on.
• Check the isolation switch on the transformer
is turned on.
No image
• Ensure everything is switched on including the
monitor which can be switched off by accident.
• Unplug camera head, colour bars should appear.
If no colours appear, contact Olympus Service
Helpdesk.
Dark image
• Check condition of telescope.
• Check condition of light lead.
• Check fit of light lead is it firmly connected with
a click.
Dialog
1
Scope information
2
3
4
No. Nomenclature Description
1 User preset name Displays the user preset name.
2 Scope model Displays the model name of the camera head
3 Serial number Displays the serial number of the camera head
4 Remote switch Displays the function assigned to the remote switch
Issue 1
05/02/2021
KMF-08927
NCDR 02863

K
eyMed House, Stock Road, Southend-on-Sea, Essex, SS2 5QH, UK
Olympus Medical UKIE Olympus Medical Europe @OlympusMedUKIE
KeyMed House, Stock Road, Southend-on-Sea, Essex, SS2 5QH, UK
Olympus Medical UKIE Olympus Medical Europe
@OlympusMedUKIE
For further information, please contact
Olympus Customer Services on 01702 616 333
or visit www.olympus.co.uk
Issue 1
05/02/2021
KMF-08927
NCDR 02863