Olympus EMPOWER EMP-H35S User manual

OLYMPUS EMPOWER™Ho:YAG LASERS
QUICK REFERENCE GUIDE
EMP-H35S/EMP-H65S/EMP-H100S

2EMP-H35S, EMP-H65S & EMP-H100S QUICK REFERENCE GUIDE
This guide is designed as a quick reference guide only. It is not a
substitute for reading the entire Operators Manual and/or Instructions
For Use (IFU) provided with the EMP-H35S, EMP-H65S or EMP-H100S
OLYMPUS EMPOWER laser system Olympus cannot encourage or
recommend any actions that deviate or are not covered by the IFU.

EMP-H35S, EMP-H65S & EMP-H100S QUICK REFERENCE GUIDE 3
LASER SET-UP
H35 Foot Switch H65 & H100 Dual
Foot Switch
Interlock Connector
Unlock Key
OLYMPUS EMPOWER Laser Fiber
Connect power cord
nVisually inspect the power cable for any tears or cracks, do not use if it appears to be damaged
in any way. Connect the female end of the plug into the power port on the rear side of the system.
Connect the foot switch
nTo connect the foot switch, plug its connector into the socket on the front panel of the laser. Once inserted,
twist the silver ring clockwise until tight to secure the connection.
Required parts
Power Cord
OLYMPUS EMPOWER Laser Fiber
Unlock Key
Foot Switch
Interlock Connector
1
2
3
4
5
H65 & H100 Power CordH35 Power Cord
1
2
345

4EMP-H35S, EMP-H65S & EMP-H100S QUICK REFERENCE GUIDE
LASER OPERATION
Turn the unlock key to start the device
n
Make sure the red emergency stop button is not pressed. To reset the emergency stop button, turn the
knob clockwise.
n The unlock key turns the device on and off. To switch the device ON, insert the key and turn it clockwise,
90 degrees, to the vertical position. The ring around the fiber connection will light up (white on the H35
and blue on the H65 and H100) to indicate the system is powering on.
nThe Laser will run a self-check of all system components. If an error occurs during start up, the laser will
display an error code. If this occurs, restart the device. If the error still remains, contact Olympus Service.
Once the system check is complete, the home screen will load.
Turn
clockwise,
90°
Only the H65 and H100 show a System Check Screen
H35 Rear Panel H65 & H100 Rear Panel
Check rear power switch
nCheck the rear power switch ensuring it is flipped to the active (“I”) position.

EMP-H35S, EMP-H65S & EMP-H100S QUICK REFERENCE GUIDE 5
LASER OPERATION
Connect the laser fiber
H35 Standby and Ready screens H65 & H100 Standby and Ready screens
nThe fiber is connected to the device
through the fiber port on the front panel.
nThe fiber connector has an additional
ring which facilitates the clamping of
the fiber to the connector on the device.
Furthermore, this ring enables the
automatic detection of fiber status
(present/absent), its diameter and its
type (single use/reusable). If the fiber
is not connected to the device, an error
message is displayed when the device
is switched on.
nOn the H65 and H100, a dedicated sensor
recognizes the presence of the user
hand, opening the external protection
shutter of the fiber connector.
Standby/Ready
nWhen the user presses the Ready/Standby buttons, the system will be set in the Ready or Standby mode,
respectively. The button on the footswitch, or the Ready/Standby display area can be used interchangeably.
nIn Standby mode, the laser is not firing and the system cannot emit energy.
nIn the Ready mode, the laser is firing and ready to emit energy.

6EMP-H35S, EMP-H65S & EMP-H100S QUICK REFERENCE GUIDE
LASER OPERATION
Adjust the aiming beam
nSelect the aiming beam button on the main screen.
nThe pop up displays the aiming beam intensity with an option to adjust, as well as the option
to select a solid or blinking aiming beam.
Laser parameter adjustment
nPress the touch screen to adjust the parameters on the selected emission mode.
nUse the +/- buttons to adjust the energy and frequency.
nPress the Emission Mode area to change the Emission mode.
nOn the H65 and the H100 the pulse width can be further adjusted after the selection of a certain
mode. Select the drop down arrow to change the pulse duration to short, medium or long pulse.

EMP-H35S, EMP-H65S & EMP-H100S QUICK REFERENCE GUIDE 7
LASER OPERATION
Saving settings on the H65 and H100
nOn the H65 and H100, settings can be saved under presets to use again.
nFrom the main screen, select the settings button and then choose presets.
nIn the Presets screen, select new to save current settings as a new preset. Enter a name for the preset
and click OK. This setting can be referenced again by selecting Presets on the home screen.
H35 Emission and Ready screens H65 & H100 Emission and Ready screens
Activating the laser
nTo activate the laser, first put the laser in READY mode by pressing the READY button on the screen or
the circular button on the foot switch. If using the foot switch button, note that the button must be held
down for a few seconds to activate (until beep is heard). This is a safety feature to prevent accidental
button pressing.
nStep on the foot pedal to activate the laser.

8EMP-H35S, EMP-H65S & EMP-H100S QUICK REFERENCE GUIDE
LASER OPERATION
Manual mode on the H65 and H100
nOn the H65 and H100, Manual mode may be selected on the home screen instead of a treatment type.
Selecting this mode will load the main screen without a pedal selection.
nIn Manual mode, the energy, frequency, and pulse width modes are entered manually and can be saved
as a preset.
Viewing Fiber information
The Laser RFID system recognizes information on the OLYMPUS EMPOWER Laser Fiber and its use history.
nTo display the data, touch the Fiber Info button on the Main screen.
nThe pop up will display fiber size and type, number of uses, and date of last use.
nFor a given procedure, the Main screen displays total energy (joules) and total time (seconds) emitted
through the fiber.

EMP-H35S, EMP-H65S & EMP-H100S QUICK REFERENCE GUIDE 9
LASER OPERATION
DEFINITIONS
Hertz (Hz): Frequency or Number of pulses for each second.
Joules (J)/millijoules (mJ): A Unit of energy, the force with which each laser pulse hits the stone.
Watts (W): Unit of power equal to the total energy expenditure in 1 second (Hz x Joules = Watts).
Laser Fiber Selection Guide
Part Number
Fiber Size
μm (Core) μm (OD) French (OD)
EMP-FBX200HS
EMP-FBX200HR 200 380 1.14
EMP-FBX200BHS
EMP-FBX200BHS-C 200 Series 420 1.26
EMP-FBX272HS
EMP-FBX272HR
EMP-FBX272HS-C
EMP-FBX272HR-C
272 420 (jacket)* 1.26
EMP-FBX365HS
EMP-FBX365HR 365 570 1.71
EMP-FBX550HS
EMP-FBX550HR 550 750 2.25
EMP-FBX1000HS
EMP-FBX1000HR 1000 1450 4.35
*The Max outer diameter for the Ball-Tip fiber is given by the distal ball diameter with is 0.7±0.1mm

OLYMPUS EMPOWER™is a registered trademark of Olympus Corporation, Olympus America Inc., and/or their affiliates.
Medical devices listed may not be available for sale in all countries.
For more information, contact your Olympus
sales representative, or call 800-848-9024.
www.medical.olympusamerica.com
©2019 Olympus America Inc. All rights reserved.
Printed in USA OAIURO0319QRG29921
Distributed by
136 Turnpike Road, Southborough, MA 01772