Omnia LEVEL User manual

OMNIA
+LEVEL
Smart Auxiliary Deadbolt
Instructions / Template for Single Cylinder
Tools Needed:
Doors Prepared with 21/8” Cutout
1- No.1 and No.2 Phillips screwdrivers
2- Measuring device
3- Flathead screwdriver
4- Pliers or hacksaw
5- Metal file
800-310-7960 /www.OMNIAindustries.com
Parts Enclosed:
A- Tailpiece Cylinder with Studs
B- Cylinder Collar
C- Cylinder Collar Extender
D- Mounting Plate for Cylinder
E- 2 – 2” Cylinder Mounting
Screws
F- Inside Turnpiece & Rose
G- 2 –
3/4” Thru-bolt Screws
for Turnpiece & Rose
H- Level Strike
I- 2 – 11/2” Mounting Screws
for Level Strike
J- Battery Cap
K- CR2 Battery
L- Level Deadbolt
M- Level Deadbolt Housing
N- Hub of Level Bolt
O- 2 – 1” Mounting
Screws for Level
Deadbolt Faceplate
N
B
C
E
F
G
D
I
N
H
JKO
O
LM
Slide Fonto tailpiece and fasten using Gscrews.
6
Slide Athrough
Band Cand
then insert end of
tailpiece into hub of
M.Test fit length of
tailpiece into Fon
other side of door
to determine where
to trim the tailpiece.
3
Slide Athrough Band Cand then insert end of
tailpiece into hub of M. On other side of door, slide
tailpiece through the larger hole of Dand attach
using Escrews. Remove studs on cylinder, if required.
5
Adjust backset on Lfor door, 23/8”
(S) or 23/4”(L). Insert Lthrough
edge of door deadbolt hole and
fasten to door with Owood screws.
Insert Minto 21/8” bore and fit N
into M.
1
E
G
O+L-AuxDB 0522
(L)
B
A
M
C
B
AD
C
E
MF
G
A
Trim the appropriate amount of length from
tailpiece using either a hacksaw or break with a
pair of pliers.The tailpiece may need to be filed
down to assure proper movement of the Level
bolt when used electronically.
4
While Mis inside of 21/8” bore , attach Lto M
using screw already assembled to body of M.
2
LM
M
N
O
O
L
M
(S)
L

Attach Hto door frame with Iscrews.
7/8
13/4
DOOR
DRILL
1
DIA. HOLE
IN DOOR EDGE
5/32
FACEPLATE
23/8
BACKSET
23/4
BACKSET
21/8
BORE
DEADBOLT LATCH TEMPLATE
CAUTION: DOOR AND FRAME MANUFACTURERS When door gasketing or silencers are used, proper allowances must be made for strike location to maintain a common centerline with lock and door so that the bolt will freely enter strike.
FOLD ALONG DOOR EDGE
1x 21/4
800-310-7960 /www.OMNIAindustries.com O+L-AuxDB 0522
I
H
Insert battery Kinto deadbolt Land thread
the correct Jcover for backset onto deadbolt.
7 8
for a 23
/
4
”backset (L)
for a 23
/
8
”backset (S)
Test proper orientation of deadbolt, electronically. First test the operation with the door
in the open position, and then test the deadbolt in the closed position. When closed,
always test from the inside of the door (in order to prevent getting locked out).
Testing
Congratulations - Your installation is now complete! If you have any trouble,
please call OMNIA at the number listed below. We thank you for your purchase.
KL
J