Omnik NS Series User manual

User Manual V1.0
External LCD Display
For Omnik NS Series Inverters
User Manual
-Safety Regulation

Table of Contents
1. General Introduction....................................................................................................... 2
1) Applied models........................................................................................................ 2
2) Methods................................................................................................................... 2
2. External LCD Display...................................................................................................... 2
1) Setting ..................................................................................................................... 3
a) Control Panel.................................................................................................... 3
b) Menu Structure ................................................................................................. 4
c) Operation.......................................................................................................... 5
3. App Local Function......................................................................................................... 7
1) Download and Install ............................................................................................ 7
2) Operation Instructions .......................................................................................... 7
a) Connect to the inverter...................................................................................... 7
b) Change safety regulation .................................................................................. 9
4. Remote control..............................................................................................................10

1.General Introduction
1) Applied models
The models apply for the methods described in the following manual:
Omniksol-2k/2.5k/3k-TL3-S-NS
Omniksol-3k/3.68k/4k/4.6k/5k/6k-TL3-NS
Omniksol-5k/6k-TH/8k/10k/13k/16k-TL3-NS
Omniksol-20k/25k/30k-TL3-NS
and other upcoming models with “NS”
2) Methods
There are three methods in configuring your NS model inverters:
External LCD display;
App (local function);
Remotely.
Choose suitable method in different circumstances.
2.External LCD Display
The external LCD display is a tool designed for personal installation and maintenance. In case
of:
the end-user installed a product without any monitoring device;
Configure the product before shipping out for installation.

1) Setting
a)
Fig. 1 Front View
Control Panel
Fig. 2 Top View
Object Name Description
1 COM1 Connect to WIFI or GPRS module for remote update
2 COM2 Connect to the inverter for local operation and modify inverter
parameters

Main Interface
Info
Error
Set
SN
Model
Err No.
Err Time
Err Deta il
Page1
Ti me
Language
Password
Safety
Protection
Param Set
Freq Limit
Volt Limit
Auto Test
Test Result
System Status
Safety
Current Power
Today Energy
PV1 Volt&Current
PV2 Volt&Current
To tal E ne rg y
PV Input Mode
Page2
Page3
Grid Volt&Current
&Freq
Grid Volt&Current
&PF
Date&Time
Page4
Page5
Page6
Temperature Page7
b) Menu Structure

c)
The default interface will be shown once the “Com2” is connected to the inverter. The
screen shows the interface as “Fig. 3” indicating the system is started up. This
interface will also be shown when the display is not operated for a while.
Terminology the default interface:
Operation
“Safety” the country selection of safety regulation;
“Power” the instant output power;
“E-Today” total power generated within the day.
“Wait/Fault/Normal” the inverter system running status;
“XXs” the countdown of this Inverter to connect to the grid.
Wait/Fault/Normal XXs Safety
Power W
E-Today kWh
INFO Error Set
Fig. 3 Default interface
i.
On the main interface, you can scroll down to next page by pressing the "Enter"
botton. The interface shows as in Fig. 4 by pressing “Enter” once. There are 7 pages
information in total.
Browsing information
E-Total kWh
PV Input Mode
Fig. 4 Page 2 interface
“E-Total” on the page 2 interface means the power generated since the inverted has
been installed. (Different meaning from the “E-Total” on the main interface)
ii.
On the main interface, press the button “Down” to select “Info | Error | Set”, then
press the button “Enter” into the submenu.
Configuration

The SN code, inverter model, firmware version, and hardware version of this inverter
can be seen in the “Info”.
Up to 20 recent faults can be seen in the “Error”, including fault code, time of fault
occurrence, and detailed fault description.
“Set” is used to set inverter time, language, password, security, protection etc.
End-users can set Date Time, Language by themselves. There is an installer
password required to operate on other advance settings, e.g. safety, password,
protection etc.
Note: Please contact with your installer or Omnik service team for the
installer password. The default factory default password is 500005.
Protection
XXXXXX
Fig. 5 Inputting password
Password input interface is as Fig. 5. Use the “Up” or “Down” button to select the
number. After setting the first digit, press the “ENTER” button to set the next number.
If the password was entered correctly, you can enter the setting interface, otherwise
re-enter.
User can set safety regulation according to different countries and grid-tied
standards.
Country XXX
Select Germany
France
Italy
Fig. 6 Safety regulation selection
As in Fig. 6, XXX is the current country regulation selection candidate. Press the “Up”
and “Down” keys to select the local security country and press “Enter” to confirm it.

3.App Local Function
The App local function can be used only when the inverter is installed with a WIFI or GPRS
stick.
1) Download and Install
Search for “Solarman Pro” in AppStore /Google Play or scan the QR code to
download the Solarman Pro APP. The icon after installation is shown in the right
figure.
2) Operation Instructions
a)
Connect the cell phone to the WIFI stick via WIFI AP link. Usually the WIFI
configuration is in the settings of the cell phone. The name of the WIFI is S/N number
of the WIFI stick.
Connect to the inverter

Press on the icon to access App.
Press on "All"
Press on "Local Mode" to enter the scanning interface, scan the QR code on
the WIFI stick
Press on “Next” and prompt “Are you sure you have connected to the ***
WIFI?”
Press on “Confirm”

b) Change safety regulation