Omron CP1H CPU UNITS - PROGRAMMING 05-2007 User manual

Cat. No. W450-E1-06
CP1H CPU Unit
SYSMAC CP Series
CP1H-X40D_-_
CP1H-XA40D_-_
CP1H-Y20DT-D
OPERATION MANUAL

CP1H-X40D@-@
CP1H-XA40D@-@
CP1H-Y20DT-D
CP1H CPU Unit
Operation Manual
Revised March 2009

iv

v
Notice:
OMRON products are manufactured for use according to proper procedures
by a qualified operator and only for the purposes described in this manual.
The following conventions are used to indicate and classify precautions in this
manual. Always heed the information provided with them. Failure to heed pre-
cautions can result in injury to people or damage to property.
!DANGER Indicates an imminently hazardous situation which, if not avoided, will result in
death or serious injury. Additionally, there may be severe property damage.
!WARNING Indicates a potentially hazardous situation which, if not avoided, could result
in death or serious injury. Additionally, there may be severe property damage.
!Caution Indicates a potentially hazardous situation which, if not avoided, may result in
minor or moderate injury, or property damage.
OMRON Product References
All OMRON products are capitalized in this manual. The word “Unit” is also
capitalized when it refers to an OMRON product, regardless of whether or not
it appears in the proper name of the product.
The abbreviation “Ch,” which appears in some displays and on some OMRON
products, often means “word” and is abbreviated “Wd” in documentation in
this sense.
The abbreviation “PLC” means Programmable Controller. “PC” is used, how-
ever, in some CX-Programmer displays to mean Programmable Controller.
Visual Aids
The following headings appear in the left column of the manual to help you
locate different types of information.
Note Indicates information of particular interest for efficient and convenient opera-
tion of the product.
1,2,3... 1. Indicates lists of one sort or another, such as procedures, checklists, etc.
OMRON, 2005
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form, o
r
by any means, mechanical, electronic, photocopying, recording, or otherwise, without the prior written permission o
f
OMRON.
No patent liability is assumed with respect to the use of the information contained herein. Moreover, because OMRON is con-
stantly striving to improve its high-quality products, the information contained in this manual is subject to change without
notice. Every precaution has been taken in the preparation of this manual. Nevertheless, OMRON assumes no responsibility
for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained in
this publication.

vi
Unit Versions of CP-series CPU Units
Unit Versions A “unit version” has been introduced to manage CPU Units in the CP Series
according to differences in functionality accompanying Unit upgrades.
Notation of Unit Versions
on Products
The unit version is given to the right of the lot number on the nameplate of the
products for which unit versions are being managed, as shown below.
Confirming Unit Versions
with Support Software
CX-Programmer version 6.1 or higher can be used to confirm the unit version
using one of the following two methods. (See note.)
•Using the PLC Information
• Using the Unit Manufacturing Information
Note CX-Programmer version 6.1 or lower cannot be used to confirm unit versions
for CP-series CPU Units.
PLC Information
• If you know the device type and CPU type, select them in the Change
PLC Dialog Box, go online, and select PLC - Edit - Information from the
menus.
• If you don't know the device type and CPU type but are connected directly
to the CPU Unit on a serial line, select PLC - Auto Online to go online,
and then select PLC - Edit - Information from the menus.
In either case, the following PLC Information Dialog Box will be displayed.
Lot No.
CP1H-XA40CDR-A
CPU UNIT
Lot No. 28705 0000 Ver.1.0
OMRON Corporation MADE IN JAPAN
Product nameplate
CP-series CPU Unit
Unit version (Example for Unit version 1.0)

vii
Use the above display to confirm the unit version of the CPU Unit.
Unit Manufacturing Information
In the IO Table Window, right-click and select Unit Manufacturing informa-
tion - CPU Unit.
The following Unit Manufacturing information Dialog Box will be displayed.
Unit version

viii
Use the above display to confirm the unit version of the CPU Unit connected
online.
Using the Unit Version
Labels
The following unit version labels are provided with the CPU Unit.
These labels can be attached to the front of previous CPU Units to differenti-
ate between CPU Units of different unit versions.
Unit version
Ver.
1.0
Ver.
1.0
Ver.
Ver.
These Labels can be used
to manage differences
in the available
functions among the Units.
Place the appropriate label
on the front of the Unit to
show what Unit
version is actually being
used.

ix
Functions Supported by Unit Version for CP-series CPU Units
Functions Supported by
Unit Version 1.0 and 1.1
Functionality is the same as that for CS/CJ-series CPU Units with unit version
3.0. The functionality added for CS/CJ-series CPU Unit unit version 4.0 is not
supported.
CP1H CPU Units
• CX-Programmer version 6.11 or higher is required to use CP1H-X@@@@-
@/XA@@@@-@with unit version 1.1 or 1.0.
• CX-Programmer version 6.20 or higher is required to use CP1H-Y@@@@-
@with unit version 1.1.
Note 1. The unit version for the CP1H-X@@@@-@/XA@@@@-@begins at 1.0.
2. The unit version for the CP1H-Y@@@@-@begins at 1.1.
3. CX-Programmer version 7.11 or higher is required to use CP1L CPU Units
with unit version 1.0.
4. CX-Programmer version 7.3 or higher is required to use CP1L CPU Units
with 10 I/O points.
CPU Unit CP1H CPU Unit
Model CP1H-@@@@-@
CP1H-XA@@@@-@
(See note 1.)
CP1H-Y@@@@-
@
(See note 2.)
Unit version
Function
Ver. 1.1 or later Ver. 1.0 Ver. 1.1
Pulse
outputs
Allocated built-
in I/O terminals
4 axes at 100 kHz 2 axes at 100 kHz
2 axes at 30 kHz
2 axes at 100 kHz
Special pulse
output terminals
None 2 axes at 1 MHz

x