Omron SYSMAC SRM1-V2 User manual

Cat.No. W318–E1–4
Master Control Units
CompoBus/S
SRM1(-V2)
OPERATION MANUAL

CompoBus/S
SRM1(-V2) Master Control Units
Operation Manual
Revised May 2000

!
!
!
v
Notice:
OMRON products are manufactured for use according to proper procedures by a qualified operator
and only for the purposes described in this manual.
The following conventions are used to indicate and classify precautions in this manual. Always heed
the information provided with them. Failure to heed precautions can result in injury to people or dam-
age to property.
DANGER Indicates an imminently hazardous situation which, if not avoided, will result in death or
serious injury.
WARNING Indicates a potentially hazardous situation which, if not avoided, could result in death or
serious injury.
Caution Indicates a potentially hazardous situation which, if not avoided, may result in minor or
moderate injury, or property damage.
OMRON Product References
All OMRON products are capitalized in this manual. The word “Unit”is also capitalized when it refers
to an OMRON product, regardless of whether or not it appears in the proper name of the product.
The abbreviation “Ch,”which appears in some displays and on some OMRON products, often means
“word”and is abbreviated “Wd”in documentation in this sense.
The abbreviation “PC”means Programmable Controller and is not used as an abbreviation for any-
thing else.
Visual Aids
The following headings appear in the left column of the manual to help you locate different types of
information.
Note Indicates information of particular interest for efficient and convenient operation
of the product.
1, 2, 3... 1. Indicates lists of one sort or another, such as procedures, checklists, etc.
OMRON, 1997
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any
form, or by any means, mechanical, electronic, photocopying, recording, or otherwise, without the prior written permis-
sion of OMRON.
No patent liability is assumed with respect to the use of the information contained herein. Moreover, because OMRON is
constantly striving to improve its high-quality products, the information contained in this manual is subject to change
without notice. Every precaution has been taken in the preparation of this manual. Nevertheless, OMRON assumes no
responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the informa-
tion contained in this publication.

TABLE OF CONTENTS
vii
PRECAUTIONS xi. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 Intended Audience xii. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 General Precautions xii. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 Safety Precautions xii. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 Operating Environment Precautions xiii. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5 Application Precautions xiii. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 1
Introduction 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-1 SRM1 Features and Functions 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-2 System Configuration 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-3 Procedures From System Design to Test Operation 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-4 I/O and Data Area Allocations 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 2
Specifications and Components 11. . . . . . . . . . . . . . . . . . . .
2-1 Specifications 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-2 Unit Components 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 3
Installation and Wiring 17. . . . . . . . . . . . . . . . . . . . . . . . . . .
3-1 System Design 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-2 Selecting an Installation Site 19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-3 Installing the SRM1 20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-4 Wiring and Connections 21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-5 One-to-one NT Link 30. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-6 One-to-N NT Link 30. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-7 One-to-one PC Link Connections 31. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 4
Using the Programming Console 33. . . . . . . . . . . . . . . . . . .
4-1 Basic Operations 34. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-2 Programming Console Operations 36. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 5
Test Runs and Error Processing 59. . . . . . . . . . . . . . . . . . . .
5-1 Startup Procedure 60. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-2 Entering the Program 62. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-3 Test Run 71. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-4 Error Processing 72. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-5 Programming Console Operation Errors 75. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-6 Programming Errors 75. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-7 Troubleshooting Flowcharts 77. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 6
Expansion Memory Unit 83. . . . . . . . . . . . . . . . . . . . . . . . . .
6-1 Overview 84. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-2 Specifications and Nomenclature 85. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-3 Handling 86. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

TABLE OF CONTENTS
viii
Appendices
A Standard Models 93. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B External Dimensions 97. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Glossary 99. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Index 115. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Revision History 119. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ix
About this Manual:
The SRM1 is a special CompoBus/S controller that provides remote I/O with greatly reduced wiring. A
distributed I/O system with up to 32 Slaves and 256 I/O points can be constructed. There are two manuals
describing the setup and operation of the SRM1: The SRM1(-V2) Operation Manual (this manual) and the
CPM1/CPM1A/CPM2A/CPM2C/SRM1(-V2) Programming Manual (W353).
This manual describes the system configuration and installation of the SRM1 and provides a basic ex-
planation of operating procedures for the Programming Consoles and introduces the capabilities of the
SYSMAC Support Software (SSS). Read this manual first to acquaint yourself with the SRM1.
The CompoBus/S Operation Manual (W266) provides descriptions of the CompoBus/S system and
Units.
The CPM1/CPM1A/CPM2A/CPM2C/SRM1(-V2) Programming Manual (W353) provides detailed de-
scriptions of the SRM1’s programming functions. The SYSMAC Support Software (SSS) Operation
Manuals: Basics (W247) and C-series PCs (W248) provide descriptions of SSS operations for the SRM1
and C-series PCs.
The SYSMAC-CPT Support Software Quick Start Guide (W332) and User Manual (W333) provide
descriptions of ladder diagram operations in the Windows environment.
The WS02-CXPC1-E CX-Programmer User Manual (W361) and the CX-Server User Manual (W362)
provide details of operations for the WS02-CXPC1-E CX-Programmer.
Please read this manual carefully and be sure you understand the information provide before attempting
to install and operate the SRM1.
Section 1 describes the SRM1’s special features and functions and shows the possible system configu-
rations.
Section 2 provides the technical specifications of the SRM1 and describes its main components.
Section 3 explains how to install and wire the SRM1. Be sure to follow the instructions contained here
concerning the control panel, power supply, CompoBus/S transmissions, and RS-232C Port wiring.
Section 4 explains how to use the Programming Console. Be sure to read this section carefully if you are
not already familiar with Programming Console operations.
Section 5 describes procedures for trial runs of SRM1 operation, self-diagnosis functions, and error pro-
cessing to identify and correct the hardware and software errors that can occur during operation.
Section 6 describes how to use the CPM1-EMU01-V1 Expansion Memory Unit. Follow the handling pre-
cautions and procedures to properly use the Unit.
Appendix A provides a list of standard models.
Appendix B provides the external dimensions.
WARNING Failure to read and understand the information provided in this manual may result in
personal injury or death, damage to the product, or product failure. Please read each
section in its entirety and be sure you understand the information provided in the section
and related sections before attempting any of the procedures or operations given.
!

xi
PRECAUTIONS
This section provides general precautions for using the SRM1 and related devices.
The information contained in this section is important for the safe and reliable application of the SRM1. You must read
this section and understand the information contained before attempting to set up or operate a CompoBus/S System.
1 Intended Audience xii. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 General Precautions xii. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 Safety Precautions xii. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 Operating Environment Precautions xiii. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5 Application Precautions xiii. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

!
!
!
!
3Safety Precautions
xii
1 Intended Audience
This manual is intended for the following personnel, who must also have knowl-
edge of electrical systems (an electrical engineer or the equivalent).
•Personnel in charge of installing FA systems.
•Personnel in charge of designing FA systems.
•Personnel in charge of managing FA systems and facilities.
2 General Precautions
The user must operate the product according to the performance specifications
described in the operation manuals.
Before using the product under conditions which are not described in the manual
or applying the product to nuclear control systems, railroad systems, aviation
systems, vehicles, combustion systems, medical equipment, amusement
machines, safety equipment, and other systems, machines, and equipment that
may have a serious influence on lives and property if used improperly, consult
your OMRON representative.
Make sure that the ratings and performance characteristics of the product are
sufficient for the systems, machines, and equipment, and be sure to provide the
systems, machines, and equipment with double safety mechanisms.
This manual provides information for programming and operating the OMRON
SRM1. Be sure to read this manual before attempting to use the software and
keep this manual close at hand for reference during operation.
WARNING It is extremely important that an SRM1 and all CompoBus/S Units be used for the
specified purpose and under the specified conditions, especially in applications
that can directly or indirectly affect human life. You must consult with your
OMRON representative before applying a CompoBus/S System to the
abovementioned applications.
3 Safety Precautions
WARNING Never attempt to disassemble any Units while power is being supplied. Doing so
may result in serious electrical shock or electrocution.
WARNING Never touch any of the terminals while power is being supplied. Doing so may
result in serious electrical shock or electrocution.
WARNING Provide safety measures in external circuits (i.e., not in the Programmable
Controller), including the following items, in order to ensure safety in the system
if an abnormality occurs due to malfunction of the PC or another external factor
affecting the PC operation. Not doing so may result in serious accidents.
•Emergency stop circuits, interlock circuits, limit circuits, and similar safety
measures must be provided in external control circuits.
•The PC will turn OFF all outputs when its self-diagnosis function detects any
error or when a severe failure alarm (FALS) instruction is executed. As a coun-
termeasure for such errors, external safety measures must be provided to en-
sure safety in the system.
•The PC outputs may remain ON or OFF due to deposition or burning of the
output relays or destruction of the output transistors. As a countermeasure for
such problems, external safety measures must be provided to ensure safety in
the system.

!
!
!
!
!
5Application Precautions
xiii
WARNING When transferring programs to other nodes, or when making changes to I/O
memory, confirm the safety of the destination node before transfer. Not doing so
may result in injury.
Caution Execute online edit only after confirming that no adverse effects will be caused
by extending the cycle time. Otherwise, the input signals may not be readable.
4 Operating Environment Precautions
Do not operate the control system in the following places.
•Where the SRM1 is exposed to direct sunlight.
•Where the ambient temperature is below 0°C or over 55°C.
•Where the SRM1 may be affected by condensation due to radical temperature
changes.
•Where the ambient humidity is below 10% or over 90%.
•Where there is any corrosive or inflammable gas.
•Where there is excessive dust, saline air, or metal powder.
•Where the SRM1 is affected by vibration or shock.
•Where any water, oil, or chemical may splash on the SRM1.
Caution The operating environment of the CompoBus/S System can have a large effect
on the longevity and reliability of the system. Improper operating environments
can lead to malfunction, failure, and other unforeseeable problems with the
CompoBus/S System. Be sure that the operating environment is within the spe-
cified conditions at installation and remains within the specified conditions dur-
ing the life of the system.
5 Application Precautions
Observe the following precautions when using the SRM1.
WARNING Failure to abide by the following precautions could lead to serious or possibly
fatal injury. Always heed these precautions.
•Always turn off the power supply to the SRM1 before attempting any of the fol-
lowing.
•Assembling any devices or racks.
•Connecting or disconnecting any cables or wiring.
Caution Failure to abide by the following precautions could lead to faulty operation of the
SRM1 or the system or could damage the SRM1 or CompoBus/S Units. Always
heed these precautions.
•Fail-safe measures must be taken by the customer to ensure safety in the
event of incorrect, missing, or abnormal signals caused by broken signal lines,
momentary power interruptions, or other causes.
•Construct a control circuit so that power supply for the I/O circuits does not
come ON before power supply for the Unit. If power supply for the I/O circuits
comes ON before power supply for the Unit, normal operation may be tempo-
rarily interrupted.
•If the operating mode is changed from RUN or MONITOR mode to PROGRAM
mode, with the IOM Hold Bit ON, the output will hold the most recent status. In
such a case, ensure that the external load does not exceed specifications. (If
operation is stopped because of an operation error (including FALS instruc-
tions), the values in the internal memory of the CPU Unit will be saved, but the
outputs will all turn OFF.)

5Application Precautions
xiv
•Use the Units only with the power supplies and voltages specified in the opera-
tion manuals.
•Take measures to stabilize the power supply to conform to the rated supply if it
is not stable.
•Provide circuit breakers and other safety measures to provide protection
against short-circuiting in external wiring.
•Install all Units according to instructions in the operation manuals.
•Do not install the Units in a place where they are subject to excessive noise in
order to avoid any trouble or malfunction.
•Be sure that all the mounting screws, terminal screws, and cable connector
screws are tightened to the torque specified in the relevant manuals. Incorrect
tightening torque may result in malfunction.
•Double-check all the wiring before turning ON the power supply. Incorrect wir-
ing may result in burning.
•Do not attempt to take any Units apart, to repair any Units, or to modify any
Units in any way.
•Do not apply any impact to the Units.
•Use the cables specified in this manual and in reference manuals. Use crimp
terminals when wiring the terminal block.
•Use a signal wire duct that is separate from the one used for high-tension lines
or power lines.
•Be sure to confirm that the switch settings and wiring are correct before turning
on the power supply.
•Check the user program for proper execution before actually running it on the
Unit. Not checking the program may result in an unexpected operation.
•Confirm that the user programs run properly.
•Confirm that no adverse effect will occur in the system before attempting any of
the following. Not doing so may result in an unexpected operation.
•Changing the operating mode of the PC.
•Force-setting/force-resetting any bit in memory.
•Changing the present value of any word or any set value in memory.
•Before touching the Unit, be sure to first touch a grounded metallic object in
order to discharge any static build-up. Not doing so may result in malfunction or
damage.
•Use, store, and transport the Units within the specifications provided in this
manual.
•Resume operation only after transferring to the new SRM1 the contents of the
DM and HR Areas required for resuming operation. Not doing so may result in
an unexpected operation.
•Do not pull on the cables or bend the cables beyond their natural limit. Doing
either of these may break the cables.
•Do not place objects on top of the cables. Doing so may break the cables.
•When replacing parts, be sure to confirm that the rating of a new part is correct.
Not doing so may result in malfunction or burning.
•Be sure to observe local ordinances and laws when disposing the Units.

!
!
!
5Application Precautions
xv
Caution The following precautions are necessary to ensure the general safety of the sys-
tem. Always heed these precautions.
•Provide double safety mechanisms to handle incorrect signals that can be
generated by broken signal lines or momentary power interruptions.
•Provide external interlock circuits, limit circuits, and other safety circuits in
addition to any provided within the SRM1 to ensure safety.
Caution Be sure to clear the memory before turning on the power supply to the delivered
SRM1. The contents of the Data Memory (DM), Hold Relay (HR), and Counter
(CNT) Areas in the CPU Unit may be cleared and the AR 1314 flag (which turns
ON when the power interruption hold area is not held) may turn ON.
Caution Apply the SRM1 to a system that is not influenced by any undefined data even if
the data in the DM, HR, or CNT area is cleared when the SRM1 has been turned
off for a period exceeding the data backup period of the internal lithium battery.
If the AR 1414 flag is ON, the data will be held unless it is turned OFF by the I/O
Monitor, instructions, etc.
The system can be stopped by designating DM 6604 in the PC Setup so that a
memory error occurs when the power interruption hold area is not held (with
AR 1314 ON)
•A lithium battery in the CPU Unit is used to back up the counter values and the
contents of the DM area, and HR area. The deterioration of the lithium battery
capacity depends on the ambient temperature. The standard service life is 12
years under an ambient temperature of 40_C when operating 8 hours a day.
If the power remains off for a period exceeding the data backup period, the
contents of the Data Memory (DM), Hold Relay (HR), and Counter (CNT)
Areas in the CPU Unit may be cleared and the AR 1314 flag (which turns ON
when the power interruption hold area is not held) may turn ON.
If the contents of the CPU Unit’s program area are lost, the program stored in
flash memory will be read to the CPU Unit’s program area when the SRM1 is
started up because the contents in the read-only area (DM 6144 through
DM 6599) and PC Setup (DM 6600 through DM 6655) will be written to flash
memory.
•However, if the power is turned off without changing the mode even if changes
are made in the read-only DM area (DM 6144 through DM 6599), or PC Setup
(DM 6600 through DM 6655) using a peripheral device, the contents of
changes will not be written to flash memory. Although the data in these areas is
backed up by the lithium battery, contents of changes will disappear if the ser-
vice life of the lithium battery expires. In this case, programs in the flash
memory will be automatically read into the user program memory.
The changes can be saved by switching the SRM1 to RUN or MONITOR mode
or turning off and restarting the SRM1 soon after the changes are made.

1
SECTION 1
Introduction
This section describes the SRM1’s special features and functions and shows the possible system configurations.
1-1 SRM1 Features and Functions 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-1-1 Features 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-1-2 Functions 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-2 System Configuration 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-2-1 Basic Configuration 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-2-2 SRM1 Models 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-2-3 Peripheral Connections 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-3 Procedures From System Design to Test Operation 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-4 I/O and Data Area Allocations 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-4-1 I/O Allocations 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-4-2 Data Area Allocation 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-1SectionSRM1 Features and Functions
2
1-1 SRM1 Features and Functions
1-1-1 Features
The SRM1 is a special CompoBus/S controller that provides remote I/O with
greatly reduced wiring. The SRM1 has no built-in I/O terminals, but it can provide
the same I/O control as earlier PCs through the Slaves (Slave Terminals) that
are used for I/O.
A decentralized I/O system with up to 32 Slaves can be constructed. The system
can have up to 256 I/O points and these I/O points are controlled with the Com-
poBus/S System’s high-speed response time of 1 ms max.
A very reliable and efficiently wired system can be constructed from special
CompoBus/S components such as Analog Terminals (SRM1-C0j-V2 only),
Remote Terminals, Sensor Terminals, Communications Cables, Connectors,
and Terminators.
In SRM1-C0j-V2, the CompoBus/S system can be set to operate in long-dis-
tance communications mode in addition to the previous high-speed commu-
nications mode. This allows a main line length of up to 500 m so that I/O devices
can be controlled from some distance away. The SRM1-C0j-V2 can also pro-
cess analog data as well as digital I/O.
The SRM1’s compact design allows for a smaller and thinner control panel.
The SRM1 is equipped with a program capacity of 4K words and a DM capacity
of 2K words.
There are two SRM1(-V2) models available: the SRM1-C02-V2, which is
equipped with an RS-232C port and communications functions, and the very
cost-effective SRM1-C01-V2, which is not equipped with an RS-232C port.
1-1-2 Functions
The SRM1 is equipped with an interval timer which can be set from 0.5 ms to
319,968 ms in units of 0.1 ms. The timer can be set to trigger a single interrupt
(one-shot mode) or repeat scheduled interrupts (scheduled interrupt mode).
(The interrupts pause execution of the main program while an interrupt program
is executed.)
Low-maintenance Design Memory can be backed up without a battery by using flash memory.
Communications The SRM1 can communicate with PCs or other devices via Host Link, 1:1 NT
Link, 1:N NT Link, 1:1 PC Link, or RS-232C communications.
Port Applicable communications functions
Peripheral Port Peripheral device connections, Host Link, and RS-232C
communications
RS-232C Port Host Link, 1:1 NT Link, 1:N NT Link, 1:1 PC Link, and no-protocol
(RS-232C) communications
Programming is possible through the PT (Programmable Terminal) screen us-
ing an OMRON PT that contains Programming Console functions. (This applies
only to the SRM1-C02-V1 and SRM1-C02-V2.)
Standard Peripheral Devices The SRM1 uses the same Programming Consoles, CX-Programmer, SYSMAC-
CPT, and SYSMAC Support Software (SSS) as the Mini H-type, CQM1,
CPM1/CPM1A, and CPM2A/CPM2C PCs.
Interval Timer Function
Programming Using the
PT

1-2SectionSystem Configuration
3
The CPM1-EMU01-V1 Expansion Memory Unit is a program loader for small-
size or micro PCs. Using the CPM1-EMU01-V1, simple on-site transfer of user
programs and data memory is possible with PCs.
Peripheral port
PERIPHERAL
RS-232C
1-2 System Configuration
1-2-1 Basic Configuration
Host device
CompoBus/S Communications Cable
SRM1
Peripheral
device
Terminator
Slave Slave Slave
32 Slaves max.
Expansion Memory Unit

1-2SectionSystem Configuration
4
1-2-2 SRM1 Models
Model RS-232C port PT programming functions
SRM1-C01-V2 No No
SRM1-C02-V2 Yes Yes
The following table compares the functions in the SRM1(-V2) PCs with the func-
tions in earlier SRM1 PCs.
Function SRM1 models
SRM1-C0j-V2 SRM1-C0j-V1 SRM1-C0j
Data backup Backed up by a lithium battery with a minimum lifetime of 10
years at 25_C. Capacitor backup
Programming
Console functions Programming can be performed through a Programming Console connected to the peripheral port or an OMRON PT
connected to the RS-232C port.
Programming can be performed
through a Programming Console
connected to the peripheral port.
Data processing Bit data (ON/OFF for 16 bits) and 16-bit
analog data from Analog Units Bit data (ON/OFF status of bits)
Communications High-speed communications (previous
mode) or long-distance communications
mode
High-speed communications mode (previous
mode) only.
Connections with
host devices Host Link, no-protocol, 1:1 NT Link, 1:N NT Link, and 1:1 PC Link communications Host Link, no-protocol, 1:1 NT Link, and 1:1 PC Link communications
Instructions The instructions in earlier SRM1 PCs plus
the following instructions:
NEG(––), PID(––), SCL(66), and ZCP(––)
Basic instructions: 14
Special instructions: 77 (123 variations)
Note The Analog Terminal can be used as a slave only with version-2 models. Incor-
rect data may be transferred if an Analog Terminal is used with the wrong model.
Peripheral port
SRM1-C01-V2
(No RS-232C port)
Peripheral port
SRM1-C02-V2
(With RS-232C port)
RS-232C port

1-2SectionSystem Configuration
5
1-2-3 Peripheral Connections
The following peripherals can be connected to the SRM1(-V2) PCs. Refer to
Appendix A Standard Models for a complete list of connectable peripherals.
Slaves The following table shows the Slaves that can be connected. Refer to the Com-
poBus/S Operation Manual (W266) for more details.
Slave SRT2 Series
High-speed or long-distance
communications
SRT1 Series
High-speed
communications only
Remote Terminals SRT2-ID04 SRT1-ID04
(transistors) SRT2-ID04-1 SRT1-ID04-1
SRT2-ID08 SRT1-ID08
SRT2-ID08-1 SRT1-ID08-1
SRT2-ID16 SRT1-ID16
SRT2-ID16-1 SRT1-ID16-1
SRT2-ID16T None
SRT2-ID16T-1
SRT2-OD04 SRT1-OD04
SRT2-OD04-1 SRT1-OD04-1
SRT2-OD08 SRT1-OD08
SRT2-OD08-1 SRT1-OD08-1
SRT2-OD16 SRT1-OD16
SRT2-OD16-1 SRT1-OD16-1
SRT2-OD16T None
SRT2-OD16T-1
SRT2-MD16T
SRT2-MD16T-1
Connector SRT2-VID08S None
Terminals SRT2-VID08S-1
(transistors) SRT2-VID16ML
SRT2-VID16ML-1
SRT2-VOD08S
SRT2-VOD08S-1
SRT2-VOD16ML
SRT2-VOD16ML-1
Remote Terminals SRT2-ROC08 SRT1-ROC08
(relays) SRT2-ROC16 SRT1-ROC16
Remote Terminals SRT2-ROF08 SRT1-ROF08
(power MOSFET) SRT2-ROF16 SRT1-ROF16
Remote Modules None SRT1-ROF08
SRT1-ROF16
Analog Input
Terminal SRT2-AD04 None
Analog Output
Terminal SRT2-DA02
Sensor Amplifier SRT2-TID04S (See note 3.) SRT1-TID04S
Terminals SRT2-TKD04S (See note 3.) SRT1-TKD04S
Sensor Terminals SRT2-ID08S (See note 3.) SRT1-ID08S
SRT2-OD08S (See note 3.) SRT1-OD08S
SRT2-MD08S (See note 3.) SRT1-MD08S

1-2SectionSystem Configuration
6
Slave SRT1 Series
High-speed
communications only
SRT2 Series
High-speed or long-distance
communications
Bit Chain Terminal None SRT1-B1T
I/O Link Unit CPM1A-SRT21 None
Note 1. SRT1-series Remote Terminals and Sensor Terminals can operate in high-
speed communications mode only. Be sure to use SRT2-series Remote Ter-
minals and Sensor Terminals when the SRM1-C0j-V2 is used in long-dis-
tance communications mode.
2. The Analog I/O Terminals can be used with SRM1-C0j-V2 only.
3. To be marketed in the near future.
The long-distance communications mode can be used between SRM1-C0j-V2
Master Control Units and SRT2-series Slaves only, as shown in the following
diagram. High-speed mode must be used if even one SRT1-series Slave is in-
cluded in the CompoBus/S system.
Master Control Unit
SRM1-C0j-V2
SRT2-series Slave
High-speed or long-distance communications mode
High-speed communications mode only
Master Control Unit
SRM1-C0j,
SRM1-C0j-V1
SRT2-series Slave
The SRM1 can use a Programming Console or a personal computer running
CX-Programmer, SYSMAC Support Software (SSS), or SYSMAC-CPT as a Pe-
ripheral Device.
Programming Console
Programming Consoles are compact Peripheral Devices that support basic
functions such as writing ladder programs and monitoring SRM1 operation.
They are useful for onsite operations.
Refer to Section 4 Using a Programming Console for details on Programming
Console operations.
SYSMAC Support Software (SSS), SYSMAC-CPT, and CX-Programmer
In addition to the basic Programming Console operations, the CX-Programmer,
SYSMAC-CPT, and SSS can be used to edit ladder programs offline, save pro-
grams to disk, and perform high-level monitoring; the CX-Programmer, SYS-
MAC-CPT and SSS functions allow the user to design more efficient ladder pro-
grams. Refer to the manuals listed on the About this Manual page for details on
using them.
SYSMAC Support Software (SSS)
When using the SSS, set the PC model to the “CQM1”and observe the following
restrictions.
•Addresses will be checked according to the CQM1 address ranges, which are
wider than the SRM1 address ranges. Be sure to use only the allowable ad-
dresses.
•The CQM1 has a larger memory than the SRM1 and the amount of memory
available display will not be correct. Allow for the difference between capaci-
ties.
Compatible
Communications Modes
Peripheral Devices

1-3SectionProcedures From System Design to Test Operation
7
•Instructions will be displayed that are not supported by the SRM1. Do not use
these instructions.
CX-Programmer and SYSMAC-CPT
The following instructions cannot be programmed when using the CX-Program-
mer or SYSMAC-CPT. Errors will occur if an attempt is made to transfer them
from the PC to the computer: SCL(66)/@SCL(66), ZCP, NEG/@NEG, and PID.
An SRM1(-V2) can be connected an IBM PC/AT or compatible computer or OM-
RON PT through an RS-232C Adapter (CPM1-CIF01) mounted to the SRM1’s
peripheral port. (Use Host Link mode when connecting a PT through an
RS-232C Adapter.)
The RS-232C port on an SRM1-C02-V2 can be used to connect directly to an
IBM PC/AT or compatible computer, OMRON PT, or PC (C200HX/HG/HE,
C200HS, CQM1, CPM1, CPM1A, CPM2A, or CPM2C). (Use Host Link mode or
NT Link mode when connecting a PT directly.)
1-3 Procedures From System Design to Test Operation
The procedures from system design to test operation are explained in the sec-
tions of this manual as follows and in the CPM1/CPM1A/CPM2A/CPM2C/
SRM1(-V2) Programming Manual (W353):
1, 2, 3... 1. System Design
Refer to 3-1 System Design.
2. Installation
Refer to 3-3 Installing the SRM1.
3. Wiring
Refer to 3-4 Wiring and Connections.
4. Creating the Ladder Program
Refer to the relevant sections in the CPM1/CPM1A/CPM2A/CPM2C/
SRM1(-V2) Programming Manual (W353) and the applicable PC manual.
5. Inputting the Program
Refer to Section 4 Using the Programming Console, Section 5 Test Runs
and Error Processing,CX-Programmer Users Manual (W346), SYSMAC
Support Software (SSS) Operation Manuals (W247 and W248),and SYS-
MAC-CPT Support Software Quick Start Guide (W332) and User Manual
(W333).
6. Test Operation
Refer to 5-1-2 SRM1 Test Run Procedure.
Host Computers, PTs, and
PCs

1-4SectionI/O and Data Area Allocations
8
1-4 I/O and Data Area Allocations
1-4-1 I/O AllocationsThe input bits of SRM1 words 000 to 007, and the output bits of words 010 to 017,
are allocated to the CompoBus/S Slave. These allocations are shown in the fol-
lowing table.
I/O Word address Bits
15 to 08 07 to 00
Inputs 000 IN1 IN0
001 IN3 IN2
002 IN5 IN4
003 IN7 IN6
004 IN9 IN8
005 IN11 IN10
006 IN13 IN12
007 IN15 IN14
Outputs 010 OUT1 OUT0
011 OUT3 OUT2
012 OUT5 OUT4
013 OUT7 OUT6
014 OUT9 OUT8
015 OUT11 OUT10
016 OUT13 OUT12
017 OUT15 OUT14
IN0 to IN15 are Input Slave node numbers, and OUT0 to OUT15 are Output
Slave node numbers.
If the maximum number of CompoBus/S devices is set to 16, then IN8 to IN15
and OUT8 to OUT15 can be used as work bits.
Words IR 008, IR 009, IR 018, and IR 019 can be used as work words.
The bits for two node number are allocated to 16-point Slaves so that all bits are
in the same word. If an even node address is set, the node address that is set
and the next node address following it will be used. For example, if node address
6 is set for a 16-point Output Slave, bits for node addresses OUT6 and OUT7 will
be used. If an odd node address is set, the node address that is set and the pre-
vious node address will be used. For example, if node address 3 is set for a
16-point Output Slave, bits for node addresses OUT2 and OUT3 will be used.
All of the bits for one node address are allocated to a 4-point Slave. If an even
numbered node address is set, bits 00 to 03 are used and bits 04 to 07 are not
used. If an odd numbered node address is set, bits 8 to 11 are used and bits 12 to
15 are not used.

1-4SectionI/O and Data Area Allocations
9
Analog Terminals are allocated from 16 to 64 bits per Terminals as shown in the
following table. If an allocation is not completely within the input or output area,
communications will not be possible and the COMM indicator will not be lit.
I/O bits allocated Node
address
setting
Node addresses used Address
setting range
64 bits Even Set address to set address + 7 0 to 9
(SRT2-AD04, 4 analog inputs) Odd Set address –1 to set address + 6
48 bits Even Set address to set address + 5 0 to 11
(SRT2-AD04, 3 analog inputs) Odd Set address –1 to set address + 4
32 bits Even Set address to set address + 3 0 to 13
(SRT2-AD04, 2 analog inputs)
(SRT2-DA02, 2 analog outputs) Odd Set address –1 to set address + 2
16 bits Even Set address to set address + 1 0 to 15
(SRT2-AD04, 1 analog input)
(SRT2-DA02, 1 analog output) Odd Set address –1 to set address
Examples
If node address 3 is set for the SRT2-DA02 and 2 analog outputs are used, 32
bits are allocated from OUT2 to OUT5.
If node address 10 is set for the SRT2-AD04 and 4 analog inputs are used, the
allocated area would exceed the output area available for allocation and com-
munications would not be possible.
1-4-2 Data Area Allocation
The relationships between the data areas and words that can be used by the
SRM1 are shown in the following table. For details, refer to the CPM1/CPM1A/
CPM2A/CPM2C/SRM1(-V2) Programming Manual (W353).
Name Number of words or bits Word addresses
Input bits 8 words IR 000 to IR 007
Output bits 8 words IR 010 to IR 017
Work bits 44 words
(See note 1.) IR 008 and IR 009, IR 018 and IR 019,
IR 200 to IR 239
SR area 16 words IR 240 to IR 255
HR area 20 words HR 00 to HR 19
AR area 16 words AR 10 to AR 15
(See note 2.)
LR area 16 words LR 00 to LR 15
DM area (Read/Write) 2,022 words DM 0000 to DM 2021
DM area (Read Only) 456 words DM 6144 to DM 6599
DM area (PC Setup) 56 words DM 6600 to DM 6655
TR area 8 bits TR 0 to TR 7
TIM/CNT area 128 bits TIM/CNT 000 to 127
Note 1. When the CompoBus/S system is used in 128-bit mode, IR 004 to IR 007
and IR 014 to IR 017 can be used as work words.
2. AR 04 to AR 07 are used for Slave status.