Omron T20 User manual

I601-E-01
T20 Pendant
Userʼs Guide

Copyright Notice
The information contained herein is the property of Omron Adept Technologies, Inc., and shall not be
reproduced in whole or in part without prior written approval of Omron Adept Technologies, Inc. The
information herein is subject to change without notice and should not be construed as a commitment by
Omron Adept Technologies, Inc. The documentation is periodically reviewed and revised.
Omron Adept Technologies, Inc., assumes no responsibility for any errors or omissions in the doc-
umentation. Critical evaluation of the documentation by the user is welcomed. Your comments assist us
in preparation of future documentation. Please submit your comments to:
[e-mail].
Copyright © 2012 - 2014, 2016 by Omron Adept Technologies, Inc.
Any trademarks from other companies used in this publication
are the property of those respective companies.
Created in the United States of America

Table of Contents
Chapter 1: Introduction 5
1.1 Product Description 5
Features 5
System Compatibility 5
1.2 Proper Handling of the Pendant 5
1.3 How Can I Get Help? 6
Related Manuals 6
Chapter 2: Safety 7
2.1 Dangers, Warnings, Cautions, and Notes 7
2.2 Safety Precautions 8
2.3 What to Do in an Emergency or Abnormal Situation 8
2.4 Additional Safety Information 8
Manufacturer's Declarations 8
Robot Safety Guide 8
Chapter 3: Installation and Setup 9
3.1 Transport and Storage 9
3.2 Unpacking the Pendant 9
3.3 Repacking for Shipment 9
3.4 Operating Environment 10
3.5 Installation 10
Chapter 4: Operation 15
4.1 Using the Pendant Controls and Indicators 15
4.2 Enable Switch 17
4.3 Turning Power ON and OFF 19
Turning Robot Power ON 19
Turning OFF Power from the T20 Pendant 20
4.4 User Interface Operation 20
User Interface Controls 20
User Interface Flow Diagram 21
Displaying the Home Screens 23
4.5 Using Jog Mode 24
COMP Mode 24
T20 Pendant User's Guide, 10433-000 Rev. E
Page 3 of 50

Table of Contents
Joint Mode 25
World Mode 25
Tool Mode 26
Free Mode 27
4.6 Speed Control 28
4.7 Position Display 29
4.8 Smart Locations 30
4.9 Available Frames 30
Enable Frame-Based Jogging 31
A Note about Frame-mode Jogging 31
4.10 Available Tools 31
4.11 Location Teaching 32
Adding Approach Distance 35
Using Jog To 35
Align 35
4.12 I/O Signals 35
4.13 Displaying and Clearing Errors 37
Chapter 5: Maintenance 39
5.1 The System Maintenance Screen 39
5.2 Setting the Screen Saver 40
5.3 Setting the Initial Speed 41
5.4 Enabling Smart Locations 41
5.5 Setting the Approach Distance 41
5.6 Enabling Pendant Messages 42
5.7 Displaying System Information 42
5.8 Displaying Recent Errors 43
5.9 Updating the Pendant Firmware 44
5.10 Loss of Connection 46
5.11 Cleaning 46
5.12 Periodic Maintenance 46
Chapter 6: Technical Specifications 47
6.1 Dimension Drawings 47
6.2 Pendant Specifications 47
T20 Pendant User's Guide, 10433-000 Rev. E
Page 4 of 50

T20 Pendant User's Guide, 10433-000 Rev. E
Page 5 of 50
Chapter 1: Introduction
This manual covers the setup, operation, and user maintenance of the T20 pendant.
1.1 Product Description
The T20 pendant provides a user interface and teach pendant in an ergonomic and rugged
package. The T20 pendant is designed for right- or left-handed use. All gripping and holding
positions enable comfortable and fatigue-free operation.
Features
The safety features include:
lEmergency stop switch (dual-channel circuit)
lThree-position enable switch that prevents pendant input or robot motion when the
switch is not engaged
The software features include the ability to:
lControl the robot by enabling and disabling power and jogging the robot
lTeach locations
lUse Smart Locations, which allow you to work with locations through the Frame and
Tool screens
lDisplay robot position, system status, system identification, and error messages
lDisplay and change digital I/O
System Compatibility
The T20 pendant is compatible with any robot that is controlled by the SmartController EX
motion controller or an eAIB amplifier. The key common factor is that both of those run eV+.
1.2 Proper Handling of the Pendant
You have chosen a high-quality device that is equipped with highly-sensitive, state-of-the-art
electronics. To avoid malfunctions or damage through improper handling, and possible void-
ing of the warranty, follow these instructions during operation.
lWhen you are not using the T20 pendant, hang it on the optional wall bracket for stor-
age.
lNever place the T20 pendant with the display screen facing down, to avoid damaging
the buttons or display.
lNever place the T20 pendant on an unstable surface. It could fall to the ground and be
damaged.
lNever place the T20 pendant close to heat sources or in direct sunlight.

Chapter 1: Introduction
lAvoid exposing the T20 pendant to mechanical vibrations, excessive dust, humidity, or
strong magnetic fields.
lNever clean the T20 pendant display screen or other surfaces with solvents, abrasive
cleaners, or scrubbing sponges.
lMake sure that no foreign objects or liquids can penetrate into the T20 pendant.
WARNING: When the cable entrance cover is removed, the T20
pendant is sensitive to electrostatic discharge.
1.3 How Can I Get Help?
Refer to the corporate website:
http://www.ia.omron.com
Related Manuals
This guide covers the installation, operation, and maintenance of the T20 pendant. There are
additional manuals that cover programming the system, reconfiguring installed components,
and adding other optional components. See the table that follows. These manuals are also
available on the software disk shipped with each robot system.
Table 1-1. Related Manuals
Manual Title Description
Robot Safety Guide Contains safety information for our robots.
SmartController EX
User's Guide
Contains complete information on the installation
and operation of the SmartController EX motion con-
troller and the optional sDIO product.
ACE User's Guide Describes the ACE software environment and use
with a control system. This documentation is
included in the ACE software installation.
eV+ Language User's
Guide
Describes the eV+ language and programming of a
control system.
T20 Pendant User's Guide, 10433-000 Rev. E
Page 6 of 50

T20 Pendant User's Guide, 10433-000 Rev. E
Page 7 of 50
Chapter 2: Safety
2.1 Dangers, Warnings, Cautions, and Notes
There are six levels of special alert notation used in our manuals. In descending order of
importance, they are:
DANGER: This indicates an imminently hazardous electrical situation
which, if not avoided, will result in death or serious injury.
DANGER: This indicates an imminently hazardous situation which, if
not avoided, will result in death or serious injury.
WARNING: This indicates a potentially hazardous electrical situation
which, if not avoided, could result in serious injury or major damage to
the equipment.
WARNING: This indicates a potentially hazardous situation which, if not
avoided, could result in serious injury or major damage to the equipment.
CAUTION: This indicates a situation which, if not avoided, could result
in minor injury or damage to the equipment.
Precautions for Safe Use: This indicates precautions on what to do and
what not to do to ensure using the product safely.

Chapter 2: Safety
2.2 Safety Precautions
DANGER: An industrial robot can cause serious injury or death, or dam-
age to itself and other equipment, if the following safety precautions are
not observed:
lAll personnel who install, operate, teach, program, or maintain the system must read
this guide, read the Robot Safety Guide, and complete a training course for their respons-
ibilities in regard to the robot.
lAll personnel who design the robot system must read this guide, the Robot Safety Guide,
and the robot user's guide that was supplied with the equipment. The system design
must comply with all local and national safety regulations for the location in which the
robot is installed.
lThe robot system must not be used for purposes other than described in the robot user's
guide that was supplied with the equipment. Contact Omron Adept Technologies, Inc. if
you are not sure of the suitability for your application.
lThe user is responsible for providing safety barriers around the robot to prevent anyone
from accidentally coming into contact with the robot when it is in motion.
lPower to the robot and its power supply must be locked out and tagged out before any
maintenance is performed.
2.3 What to Do in an Emergency or Abnormal Situation
Press any E-Stop button (a red push-button on a yellow background/field) and then follow the
internal procedures of your company or organization for an emergency or abnormal situation.
If a fire occurs, use CO2to extinguish the fire.
2.4 Additional Safety Information
Manufacturer's Declarations
This lists all standards with which each robot complies. Refer to the Manufacturer's Declarations
Guide.
Robot Safety Guide
The Robot Safety Guide provides detailed information on safety for our robots. The Guide ships
with each robot.
T20 Pendant User's Guide, 10433-000 Rev. E
Page 8 of 50

T20 Pendant User's Guide, 10433-000 Rev. E
Page 9 of 50
Chapter 3: Installation and Setup
This chapter covers the installation and setup of the T20 pendant.
3.1 Transport and Storage
The T20 pendant must be shipped and stored in a temperature-controlled environment, within
the range –25° to +60° C (-13° to 140° F). The recommended humidity range is 5 to 95 percent,
non-condensing. It should be shipped and stored in the original packaging, which is designed
to prevent damage from normal shock and vibration. You should protect the packaging from
excessive shock and vibration. The pendant must always be stored and shipped in a clean,
dry area that is free from condensation.
The T20 pendant weighs 480 g (1.1 lb) without the adapter cable installed.
3.2 Unpacking the Pendant
Carefully inspect the shipping packages for evidence of damage during transit. If any damage
is indicated, request that the carrier’s agent be present at the time the container is unpacked.
Before signing the carrier’s delivery sheet, compare the actual items received (not just the pack-
ing slip) with your equipment purchase order. Verify that all items are present and that the
shipment is correct and free of visible damage.
lIf the items received do not match the packing slip, or are damaged, do not sign the
receipt. Contact Omron Adept Technologies, Inc. as soon as possible.
lIf the items received do not match your order, please contact Omron Adept Tech-
nologies, Inc. immediately.
lRetain all containers and packaging materials. These items may be necessary to settle
claims.
Remove the pendant from its box and place it on its back on a flat surface.
3.3 Repacking for Shipment
If the pendant or other equipment needs to be shipped, reverse the steps in the installation pro-
cedures in this chapter. Reuse all original packing containers and materials and follow all
safety notes used for installation. Improper packaging for shipment will void your warranty.

Chapter 3: Installation and Setup
3.4 Operating Environment
The T20 pendant is designed to operate in the following environment:
lTemperature: 0° to +45° C (32° to 113° F)
lHumidity: 0 to 95%, non-condensing
The T20 pendant is not intended for use in hazardous environments (explosive gas, water,
dust, oil, or mist). It has an IP rating of IP65.
3.5 Installation
The T20 pendant can be used with a SmartController EX motion controller or any robot system
using eV+. A Front panel is required in either case.
Note the following points:
lThe E-Stop buttons on the Front Panel and T20 pendant both function and are indi-
vidually detected.
lThe high-power-enable buttons on both devices function independently. The button on
either device can enable/disable power on the system.
About Jumper Plugs
There are two jumper, or bypass, plugs that can be used with a T20 pendant system. One is a
screw-to-lock plug (P/N 10048-000) for the pendant adapter cable, included with the T20
pendant. The other is an XMCP plug. There are two versions of the XMCP plug:
XMCP, SmartController EX version
This is P/N 10052-000, included with the controller, for the XMCP connector on
the controller.
XMCP, Cobra ePLCRobot version
This is P/N 04737-000, included with the robot, for the eAIB XSYSTEM cable.
The reason for the jumper plugs is that the pendant emergency stop switch and the enable
switch are wired into the system emergency stop circuitry. If neither cable is connected, the sys-
tem emergency stop circuitry will see this as an E-Stop having been activated, and you cannot
enable high power.
To prevent this, when either the pendant cable or the adapter cable will be unplugged, the cor-
responding jumper plug must be installed.
See the connection diagrams that follow.
Installation with an SmartController EX Motion Controller
The following figure shows a Front Panel and an T20 pendant connected to a SmartController
EX motion controller. See the SmartController EX User's Guide for additional information.
T20 Pendant User's Guide, 10433-000 Rev. E
Page 10 of 50