Open Plan Systems E-TABLE-2S-T-LEG User manual

11
3 42
1 2 2 1
5 6
1
2
3
1
2
3
45
6
Use a 4 x 4 wrench (A) to unscrew the 4 screws on
the inside of the crossbeam of the folding table and
adjust the tightness of the 4 screws on the outside
to make the beam expandable.
A
4x4
A
Unscrew
4
77
Max. Weight Capacity 220.5 lbs
Height Range
Width Range
27.2"
43.3"-70.9"
-46.5"
Column Stage 2
SKU: E-TABLE-2S-T-LEG
Installation guide
Technical data
Accessory list
Attention: The drawings below are only for reference which might be slightly
different from the actual object.
A1
C
8
16
B
No. Image Spec Qty
Allen Key
4x4mm
Allen Key
5x5mm
M6
ST4.2
Component list
No. Part Qty No. Part Qty
No. Part Qty No. Part Qty
No. Part Qty No. Part Qty
No. Part Qty
Feet Foldable Legs
Side Bracket
Keypad Power Plug
Cable Tie
STEP 1
STEP 2
STEP 3
Unfold the leg (2)
Install on the end
Unfold the legs as shown in the diagram.
Install the brackets (3)
Insert
Insert
Insert the brackets (3)
Expanding the supporting beam
Expand outward
Expand out
Tighten the screws using the wrench (A)
after inserting the brackets(3).

Bx8
A
4x4
B
A
1
Install the cable management tray
A
4x4
4
Install the cable management tray(4) on the beam, and fix the
screws unscrewed in step 3 with a wrench (A)
A
2
1
Cx12
x4
5
3
C
2
5
5
6
6
STEP 4
STEP 5
STEP 6
STEP 7
Install the feet (1)
Install the work surface
All connecting cables can be fixed
with cable tie (7).
Install the work surface on the frame and fix it with
the screw(C).
Attach the keypad (5)
to the bottom of work surface
Connect the cables to the control box
Power port
Port for cable
connected to the
lifting column
Port for
keypad
Troubleshooting
The following tips will help you detect and eliminate the common issues.
Issue Method
No response while long pressing
down arrow after connected with
a power supply
1.Check if all the cables be connected well
1.Check if all the cables be connected well
2.Contact your supplier or dealer
2.Contact your supplier or dealer
No response while pressing up
arrow/ down arrow after
connected with a power supply
Rising in a low speed
1.Check if overloaded, max loading: 100kg;
1.Check if overloaded, max loading: 100kg;
1.Check if overloaded, max loading: 100kg;
2.Contact your supplier or dealer
2.Contact your supplier or dealer
2.Contact your supplier or dealer
1. Contact your supplier or dealer
1.Reposition
2.Contact your supplier or dealer
Table goes down but not up
Frequently repositing
Overworked
(Duty cycle: Max 2min on/18min OFF)
1.Restart after suspend for 18mins while
connecting with power;
2.Contact your supplier or dealer;
1. Press "M"and "3" together for 3 seconds or
more, after hearing continuous beeping for twice,
it will restore factory settings
Not enough height range
2.Contact your supplier or dealer
Waste disposal This marking indicates that this product should
not be disposed with other household wastes.
To prevent possible harm to the environment or
human health from uncontrolled waste disposal,
recycle it responsibly to promote the sustainable
reuse of material resources. To return your used
device, please use the return and collection
systems or contact the retailer where the
product was purchased. They can take this
product for environmental safe recycling.
The motor does not move as instructed
Sliding downward
Cx4
Spare screws