Open Plan Systems XPAND REACH User manual

Tools Required
For additional assembly support, refer to www.openplan.com
or contact 844.OPS.OPS1
Cordless Drill
Philips bit with extension
for Work Surface screws
(XP-Screw-WS)
Measuring Tape
3/16 Hex drive bit
for XP-Screws
Level
XPAND REACH
Conference Table – Assembly Instructions
www.openplan.com | 844.OPS.OPS1 | [e-mail]
Rubber Mallet

XPand Parts Used for Assembly
Item Part name Part Description Image
1 XP-LA Leg Assembly
2 XP-SB-Bracket Stretcher Bar Bracket
3 XP-45D-XX-TL 45 Degree Table Leg Rail, XX”
4 XP-WSSB Work Surface Support Bracket
5 XP-SB-XX Stretcher Bar, XX”
6 XP-SCREWS-WS 10-9X1 PH Pan Head, ST P’bd
Screw, ZP
7 XP-SCREWS 5/16-18 x .5” Hex Socket Cap
Screw, FT, SS
8 XP-TXXXX Work Surface
2
XPand Reach – Conference Table

XPand offers two types of end legs, Tapered legs and Rectangular legs. Though the legs look different, the assembly process is same.
Step 1: Prepare a large floor space to put the XPand order
together. Unpack the parts and check to see if all the
XPand parts are present as per the Sales Order pick list.
Rectangular leg
(XP-LA-RL)
Step 2: Assemble the Leg Rails (XP-45D-XX-TL) to the Legs using (2) XP-Screws.
Left leg
Right leg
3
XPand Reach – Conference Table
Note: The assembly Instructions are same if straight
XP-LR-XX are used in place of XP-45D-TL.
Tapered leg
(XP-LA)

Step 4: Assemble the Stretcher Bars (XP-SB-XX ) to the XP-
SB-Brackets using (2) XP-Screws per Bracket.
4
Note: The Stretcher bar is 5” shorter than the specified size.
For example, XP-SB-60 is actually 55” long.
XPand Reach – Conference Table
Step 3: Assemble (2) XP-SB-Brackets to the Leg
Rail using (2) XP-Screws per Bracket. Make sure
the Top Face of the Bracket faces upwards.
Figure A shows the Top Face of the Bracket.
Note: If multiple benches need to be ganged, don’t attach 2nd End Leg
Assembly yet. Attach XP-MLC to the other end of the Stretcher Bar .
Bracket on top/rear
indicates “Top”.
Figure A
(XP-SB-Bracket)

www.openplan.com | 844.OPS.OPS1 | [email protected]
5
Step 6: Assemble XP-WSSB to the Stretcher bars using XP-Screws
as a Set Screw. See Figure B on page 6 for additional support
locations.
XPand Reach – Conference Table
Step 5: Repeat Step 2 through 4 to assemble the other end of
Stretcher Bars.
Note: When 48” (XP-45D-48-TL) or 60” (XP-45D-60-TL) leg rails are used,
XP-WSSA-XX is used in place XP-WSSB.
Figure B
(XP-WSSA-XX)

Step 8: Level the Conference Table unit by turning the leveling feet.
www.openplan.com | 844.OPS.OPS1 | [email protected]
6
XPand Reach – Conference Table
Step 7: Center the Work Surface on the frame
and secure the Work Surface to XP-WSSB’s using
(4) XP-Screw-WS per Bracket.
Note:
Figure C shows the number of XP-WSSB’s assembled to Stretcher Bars of different lengths.
Figure C
SB < 30”
SB = 30” - 45”
SB > 45” -80”
SB = Stretcher Bar length