Original BTC 7600 User manual

Instruction Manual
v1.1-05.19 7600
Safety & Installation Instructions
1. If you are in any doubt consult a qualified electrician as to the installation of the fitting. Install in accordance with current
IEE wiring regulations. It is recommended that this fitting is installed by a qualified electrician.
2. Ensure that the electrical supply is OFF. Disconnect the electrical supply at the fuse-board.
3. If removing an existing fitting first, note all wiring connections: record which of the house wires is connected to the live,
neutral and earth terminals.
4. Carefully identify where the supply cable is (and check there are no other cables in the area) to avoid damage to concealed
wiring during installation.
5. Position the light where desired ensuring that there is suitable support adjacent to where you will connect to the house
supply and mark position of fixing holes, before drilling appropriate holes as below.
6. a. Brick or masonry: Drill holes into which the wall plugs tightly fit, then insert wall plugs.
b. Wood: No hole necessary (unless small pilot hole required), screws can be screwed directly into the timber.
c. Plaster/Cavity: Special cavity wall fittings are required, rather than provided fixings. These are widely available from
good hardware or DIY store and should come with their own instructions that must be followed. It may be easier to
relocate the fitting so that you screw directly into a timber joist or beam.
7. Support the fitting so that no strain is applied to the wiring when making the electrical connections. If necessary get a
colleague to help.
8. Electrical connection: this light fitting is low voltage. It must be connected to the mains through a 12V transformer (not
supplied). This should be a 12V AC low voltage halogen transformer, min 20VA installed a maximum of 3m away from the
fitting. No connector blocks are supplied with this product; installation should be performed by a suitably qualified person.
9. Double check all the connections are secure and that no loose strands of wire are left out of the connector, Use a good
quality electrical insulation tape to cover the connector blocks and at least 25mm of the cables going in to either end of the
connectors.
10. Check that no wires are trapped behind or within the fitting and complete the installation, referring to the Installation
diagram inside.
11. Fit the correct type and wattage of lamp (or less). Be careful not to overtighten the lamp.
12. Switch on at the fuse-board. Your light fitting is now ready for use.
Other Important Information
Switch off at mains before changing lamp(s). Never fit a lamp of greater wattage than recommended. Ensure children do not
play with the light fitting. Dispose of old lamps carefully. Never leave a fitting without a lamp in position (or someone can
accidently touch the contacts). Adjust fitting only when power to the fitting is off and has been left to cool. If the electrical flex
or electrical components become damaged at any point, power to the fitting should be disconnected immediately and not
operated until the damaged parts are fixed/replaced. For use in dry, indoor environment only. Ensure the fitting does not come
into contact with any liquids.
These instructions are provided for your safety in order to prevent the risk of Fire, Electric shock or Injury. It is vitally
important that they are read in their entirety before installing your fitting. Please retain for future reference.
MADE IN BRITAIN
ORIGINALBTC.COM
[phone]
UNIT 21 / 22 AVENUE ONE, STATION LANE, WITNEY, OX28 4XZ, ENGLAND
Established in 1990, Original BTC manufactures relaxed, familiar lighting for traditional and contemporary homes.
All products are hand-assembled in Oxford from high quality components, produced in the UK.
Cleaning and Maintenance
Metal finishes should only be cleaned with a soft, dry cloth. Do not use polishes or abrasives. Glass can be cleaned by hand,
using a soft damp cloth with a diluted mild detergent (nonabrasive) or suitable glass cleaner if necessary. Switch off power to
the fitting before cleaning. Spare parts are available for this product, please contact us on the details below.
Low Voltage Recessed Step Light

7600
PLEASE READ THE INSTRUCTIONS ON THE REVERSE BEFORE YOU BEGIN INSTALLING YOUR LIGHT
12V AC 50Hz
Installation Diagram
IP20
Installation and Assembly Instructions
With roots dating back to the shipyards of nineteenth century London, Davey Lighting combines
industrial design, traditional craftsmanship and the finest raw materials. Authentic and unique,
lights are manufactured in England with the same attention to detail required for their original
industrial purpose. Simplicity of design and choice of finish, including weathered brass and copper,
polished aluminium and galvanised cast iron, make Davey lights equally suited to traditional or
contemporary schemes.
Low Voltage Recessed Step Light
To Insert/Replace Light bulb
Ensure power is turned off and lamp is left to
cool before replacing
- Squeeze the rear reflector at the top and
bottom (A)
- Pull away from the cover/lamp assembly (B)
- To fit the lamp, ease lamp into lampholder
with a gentle rocking motion (C)
- Replace reflector by squeezing at the top and
bottom, locating the slots into the tabs (B)
Tabs
Slots
A
B
C
- Using appropriate tools, make a cut out in the wall where the light is to be installed.
- This fitting must be wired into a remote transformer, follow the instructions overleaf to intstall the light.
- Follow diagrams A, B and C to insert bulb.
- Having made the electrical connection, the fitting can be inserted into the cut out by fully squeezing the leaf
springs (D) and locating into the cut-out (E), allowing the leaf springs to hold it securely in position.
This fitting requires a remote transformer (not supplied). This should be a 12V AC low voltage halogen transformer,
min 20 VA, installed a maximum of 3m from the fitting in a suitable enclosure. This fitting should be installed by a
suitably qualified person.
12V TRANSFORMER
& MAINS CONNECTOR
(NOT SUPPLIED)
D
E
G4 CAPSULE
LAMP GUIDANCE
TYPE* WATTAGE** BASE SHAPE


HALOGEN
LED
20W MAX
3W
* Warm white (2700k) low energy lamps recommended.
** Wattage value provided as a guide to suitable lamps. Lower wattage than stated may be used.