*After 2004, wiring installation colours changed:
LIVE Brown replaces Red
EARTH Green/Yellow sleeving
NEUTRAL Blue replaces Black
120V ac 60Hz IP20
Stirrup Floor Lights Safety Instructions
Safety Instructions
Cleaning and Maintenance
These instructions are provided for your safety in order to prevent the risk of Fire, Electric shock or
Injury. Please retain for future reference. When fitting is in operation, some parts will become hot;
take care when using/handling.
- Ensure the lamp type and max wattage is followed- do not exceed. Take care not to overtighten
lamp.
- Do not touch the lamp (bulb) or lamp holder while in operation, as both become very hot.
- Turn off and unplug fitting, leaving lamp to cool before changing lamp. Dispose of old lamps
carefully.
- Adjust light fitting only when power to the fitting is off and has been left to cool.
- Never leave a fitting without a lamp in position.
- Keep light fitting away from combustible materials such as soft furnishings.
- Ensure children do not play with the light fitting.
- Ensure the light is positioned on a solid, level and non-slip surface and make sure the position of
the cable does not pose a trip hazard.
- If the electrical flex or electrical components become damaged at any point, the fitting must be
unplugged from the power supply immediately and not operated until the damaged parts are
fixed/replaced.
- For use in a dry, indoor environment only. Ensure the fitting does not come into contact with any
liquids.
Metal finishes should only be cleaned with a soft, dry cloth. Do not use polishes or abrasives. Glass
and bone china can be cleaned by hand, using a soft damp cloth with a diluted mild detergent
(nonabrasive) if necessary. Switch off power to the fitting before cleaning.
ENG WARNING – RISK OF FIRE AND ELECTRIC SHOCK.
SUITABLE FOR DRY LOCATIONS ONLY
FR ATTENTION – RISQUE D’INCENDIE, RISQUE DE CHOC.
POUR EMPLACEMENTS SECS SEULEMENT
Inspired by the searchlight on the back of a toy lorry, the Stirrup collection is the ultimate in industrial chic.
Positionable shades allow greater flexibility, enabling the user to direct the light where desired. A frosted
glass visor on the Size 2 & 3 prevents glare and provides a softer, more diffused light.
US-FF523 Stirrup 1 Floor Light
US-FF524 Stirrup 2 Floor Light, with Etched Glass
US-FF079 Stirrup 3 Floor Light with Etched Glass
US-FF484 Stirrup 3 Uplighter with Etched Glass
a
b
c
d
e
Visor Instructions (Stirrup Size 2, 3 and Uplighter)
Stirrup Size 2, 3 and uplighter are supplied fitted with an etched glass visor.
Prior to installation and re-lamping, this should be removed:
- Remove tab (a) from clip (d).
- Whilst supporting the glass (c) with one hand, undo clip to remove
glass.
Install fitting as described on opposite & reverse pages, then fit visor to
fitting:
- Hold the glass in place against the opening of the reflector (b),
- Close the clip to close the visor band (e) around the rim of the
reflector and the underside of the glass, so the visor band supports
the glass. Make sure the band secures only around the rim as it
could mark the shade if lined up incorrectly.
- Insert tab into clip, bending top and bottom around clip to hold
visor band securely to the reflector.
L
N
Live
KEY
Neutral
Earth
L =
N =
=
*Mains
Supply
Fitting
*After 2004, wiring installation colours changed:
LIVE Brown replaces Red
EARTH Green/Yellow sleeving
NEUTRAL Blue replaces Black
BROWN
GRN/YEL
BLUE
BROWN
GRN/YEL
BLUE
MADE INBRITAIN
E26 A BALL
LAMP GUIDANCE
TYPE*
WATTAGE**
BASE SHAPE
INCANDESCENT
CFL
ECO-HALOGEN
LED
40W MAX
11W
n/a
7W
* Warm white (2700k) low energy lamps recommended.
** Wattage value provided as a guide to suitable lamps. Lower wattage than stated may be used.
60W MAX
15W
n/a
12W
100W MAX
20W
n/a
18W
FF523 FF524 FF079 & FF484
