Original BTC DAVEY LIGHTING 7202 User manual

Safety & Installation Instructions Ship’s Ceiling Companionway Light
These instructions are provided for your safety in order to prevent the risk of Fire, Electric shock or Injury. It is vitally
important that they are read in their entirety before installing your fitting. Please retain for future reference.
1. If you are in any doubt consult a qualified electrician as to the installation of the fitting. Install in accordance with current IEE
wiring regulations. It is recommended that this fitting is installed by a qualified electrician.
2. Ensure that the electrical supply is OFF. Disconnect the electrical supply at the fuse-board.
3. If removing an existing fitting first, note all wiring connections: record which of the house wires is connected to the live, neutral
and earth terminals.
4. Carefully identify where the supply cable is (and check there are no other cables in the area) to avoid damage to concealed wiring
during installation.
5. Position the light where desired ensuring that there is suitable support adjacent to where you will connect to the house supply and
mark position of fixing holes, before drilling appropriate holes as below.
6. a. Brick or masonry: Drill holes into which the wall plugs tightly fit, then insert wall plugs.
b. Wood: No hole necessary (unless small pilot hole required), screws can be screwed directly into the timber.
c. Plaster/Cavity: Special cavity wall fittings are required, rather than provided fixings. These are widely available from good
hardware or DIY store and should come with their own instructions that must be followed. It may be easier to relocate the fitting
so that you screw directly into a timber joist or beam.
7. Support the fitting so that no strain is applied to the wiring when making the electrical connections.
If necessary get a colleague to help.
8. Electrical connection: this light fitting must be earthed. Make connections following the diagram below, using the terminal block
provided. A small flat-head screw driver is required.
9. To maintain the IP rating of this fitting, you must ensure that the electrical connection has suitable protection from water ingress,
housing the connection in an IP rated junction box or sealing the backplate with silicone.
10. Ensure that all electrical connections are tight, with no loose strands of wire left out of the connectors, no wires are trapped behind
or within the fitting and complete the installation, screwing the fitting to the mounting surface.
11. Fit the correct type and wattage of lamp (or less). Be careful not to overtighten the lamp.
12. Switch on at the fuse-board. Your light fitting is now ready for use.
Other Important Information
Switch off at mains before changing lamp(s). Never fit a lamp of greater wattage than recommended. Ensure children do not
play with the light fitting. Dispose of old lamps carefully. Never leave a fitting without a lamp in position (or someone can
accidently touch the contacts). Adjust fitting only when power to the fitting is off and has been left to cool. If the electrical flex
or electrical components become damaged at any point, power to the fitting should be disconnected immediately and not
operated until the damaged parts are fixed/replaced.
Cleaning and Maintenance
Metal finishes should only be cleaned with a soft, dry cloth. Do not use polishes or abrasives. Glass can be cleaned by hand, using a
soft damp cloth with a diluted mild detergent (nonabrasive) or suitable glass cleaner if necessary. Switch off power to the fitting before
cleaning. Spare parts are available for this product, please contact us on the details below.
Established in 1990, Original BTC manufactures relaxed, familiar lighting for traditional and contemporary homes.
All products are hand-assembled in Oxford from high quality components, produced in the UK.
ORIGINALBTC.COM
[phone]
UNIT 21 / 22 AVENUE ONE, STATION LANE, WITNEY, OX28 4XZ, ENGLAND
7202 / 7203
Instruction Manual
A
B
C
1
4
2
3
5
Wide gasket Narrow gasket
68 7
1
4
2
3
5
A
B
C
1
4
2
3
5
Wide gasket Narrow gasket
68 7
1
4
2
3
5
Ship’s Companionway Light
7202/E27
Ship’s Companionway Light
7203/E27
Miniature Ship’s
Companionway Light
7202/M
Miniature Ship’s
Companionway Light
7203/M
1
2
3
4
5
1
2
3
4
5
C
A
B
L
N
brown
blue
red/brown
black/blue
MainsLamp
6
Wide gasket Narrow gasket
7
1
2
3
4
5
1
2
3
4
5
C
A
B
L
N
brown
blue
red/brown
black/blue
MainsLamp
6
Wide gasket Narrow gasket
7
v1.1-04.19
L
N
Live
KEY
Neutral
Earth
L =
N =
=
*Mains
Supply
Fitting
*After 2004, wiring installation colours changed:
LIVE Brown replaces Red
EARTH Green/Yellow sleeving
NEUTRAL Blue replaces Black
BROWN
GRN/YEL
BLUE
BROWN
GRN/YEL
BLUE
MADE IN BRITAIN
E27 GLS BALL
LAMP GUIDANCE
TYPE* WATTAGE** BASE SHAPE
ü
ü
ü
ü
INCANDESCENT
CFL
ECO-HALOGEN
LED
60W MAX
15W
28W
12W
* Warm white (2700k) low energy lamps recommended.
** Wattage value provided as a guide to suitable lamps. Lower wattage than stated may be used.
L
N
Live
KEY
Neutral
Earth
L =
N =
=
*Mains
Supply
Fitting
*After 2004, wiring installation colours changed:
LIVE Brown replaces Red
EARTH Green/Yellow sleeving
NEUTRAL Blue replaces Black
BROWN
GRN/YEL
BLUE
BROWN
GRN/YEL
BLUE
MADE IN BRITAIN
E27 GLS BALL
LAMP GUIDANCE
TYPE* WATTAGE** BASE SHAPE
ü
ü
ü
ü
INCANDESCENT
CFL
ECO-HALOGEN
LED
60W MAX
15W
28W
12W
* Warm white (2700k) low energy lamps recommended.
** Wattage value provided as a guide to suitable lamps. Lower wattage than stated may be used.
L
N
Live
KEY
Neutral
Earth
L =
N =
=
*Mains
Supply
Fitting
*After 2004, wiring installation colours changed:
LIVE Brown replaces Red
EARTH Green/Yellow sleeving
NEUTRAL Blue replaces Black
BROWN
GRN/YEL
BLUE
BROWN
GRN/YEL
BLUE
MADE IN BRITAIN
E27 GLS BALL
LAMP GUIDANCE
TYPE* WATTAGE** BASE SHAPE
ü
ü
ü
ü
INCANDESCENT
CFL
ECO-HALOGEN
LED
60W MAX
15W
28W
12W
* Warm white (2700k) low energy lamps recommended.
** Wattage value provided as a guide to suitable lamps. Lower wattage than stated may be used.
L
N
Live
KEY
Neutral
Earth
L =
N =
=
*Mains
Supply
Fitting
*After 2004, wiring installation colours changed:
LIVE Brown replaces Red
EARTH Green/Yellow sleeving
NEUTRAL Blue replaces Black
BROWN
GRN/YEL
BLUE
BROWN
GRN/YEL
BLUE
MADE IN BRITAIN
E27 GLS BALL
LAMP GUIDANCE
TYPE* WATTAGE** BASE SHAPE
ü
ü
ü
ü
INCANDESCENT
CFL
ECO-HALOGEN
LED
60W MAX
15W
28W
12W
* Warm white (2700k) low energy lamps recommended.
** Wattage value provided as a guide to suitable lamps. Lower wattage than stated may be used.

A
B
C
1
4
2
3
5
Wide gasket Narrow gasket
68 7
1
4
2
3
5
7203/E27
7203/M
Ship’s Ceiling Companionway Light Installation Diagram
7202/E27 Ship’s Companionway Light
7202/M Miniature Ship’s Companionway Light
7203/E27 Ship’s Companionway Light
7203/M Miniature Ship’s Companionway Light
Contents
1 - Pan
2 - Wide gasket
3 - Narrow gasket
4 - Ring (7202)
4 - Guard (7203)
5 - Well glass
6 - 2 x Fixing screws
7 - 2 x Rawl plugs
8 - Connector block
Required for Installation
- Screwdriver, flat-head
- Small screwdriver, flat-head
- Drill (if holes are required)
Installation and Assembly Instructions
Refer to diagrams above.
Disassemble the light prior to installing by removing ring/guard (4) and well glass (5) by unscrewing
them from the pan (1). Once the lamp has been wired and the ceiling plate screwed to the ceiling (follow
instructions overleaf), insert light bulb. The lamp can then be reassembled, screwing the guard/well glass
into the pan, ensuring a tight fit. DO NOT OVER TIGHTEN.
If installing this light in an exterior or bathroom location:
- The fitting should be mounted on a smooth surface.
- A thin bead of silicone sealant should be applied around the pan (1) where it meets the ceiling to prevent
any damage caused by moisture ingress and to maintain its IP rating.
230V ac 50Hz IP54
A FIXING SCREWS
B CONNECTOR BLOCK
C MAINS SUPPLY
A
B
C
1
4
2
3
5
Wide gasket Narrow gasket
68 7
1
4
2
3
5
A
B
C
1
4
2
3
5
Wide gasket Narrow gasket
68 7
1
4
2
3
5
A
B
C
1
4
2
3
5
Wide gasket Narrow gasket
68 7
1
4
2
3
5
7202/E27
7202/M
PLEASE READ THE INSTRUCTIONS ON THE REVERSE BEFORE YOU BEGIN INSTALLING YOUR LIGHT
E27 GLS BALL
LAMP GUIDANCE
TYPE* WATTAGE** BASE SHAPE
�
�
�
�
INCANDESCENT
CFL
ECO-HALOGEN
LED
40W MAX
11W
n/a
7W
* Warm white (2700k) low energy lamps recommended.
** Wattage value provided as a guide to suitable lamps. Lower wattage than stated may be used.
L
N
Live
KEY
Neutral
Earth
L =
N =
=
*Mains
Supply
Fitting
*After 2004, wiring installation colours changed:
LIVE Brown replaces Red
EARTH Green/Yellow sleeving
NEUTRAL Blue replaces Black
BROWN
GRN/YEL
BLUE
BROWN
GRN/YEL
BLUE
MADE IN BRITAIN
E27 GLS BALL
LAMP GUIDANCE
TYPE* WATTAGE** BASE SHAPE
ü
ü
ü
ü
INCANDESCENT
CFL
ECO-HALOGEN
LED
60W MAX
15W
28W
12W
* Warm white (2700k) low energy lamps recommended.
** Wattage value provided as a guide to suitable lamps. Lower wattage than stated may be used.
60W MAX
15W
42W
12W
SBC APPLIANCE
LAMP GUIDANCE
TYPE WATTAGE* BASE SHAPE
�
�
�
�
INCANDESCENT
CFL
ECO-HALOGEN
LED
15W MAX
n/a
n/a
n/a
** Wattage value provided as a guide to suitable lamps. Lower wattage than stated may be used.