OSEE HCC6830N User manual

HCC6830N Series
HD/SD Digital Video Signal
Cross Converter
User Manual

3
Product Information
Model:
HCC6830N Series HD/SD Digital Video Signal Cross Converter
Version:
V010001
Release Date:
August 21th, 201
Company
OSEE TECHNOLOGY CO., LTD.
Contact Information
Address:
No.22 Building, No.68 zone, Beiqing Road, Haidian District,
Beijing, China
Post Code:
100094
Tel:
([phone]
Fax:
([phone]
Web:
http://www.osee-dig.com/
E-mail:
[email protected]

About this manual
Important
The following symbols are used in this manual:
The further information or know-how for described subjects above which
helps user to understand them better.
The safety matters or operations that user must pay attention to when using
this product.
Contents
The user manual applies to the following device types:
HCC6830N
HCC6830NS
The images of HCC6830Nare adopted in the following descriptions.
Any of the different specifications between the device types are elaborated.
Before reading the manual, please confirm the device type.

Contents
Contents ..........................................................................................................I
Chapter 1 Product Overview .........................................................................1
Chapter 2 Safety.............................................................................................5
Chapter 3 Unpack and Installation ...............................................................7
Chapter 4 Features ......................................................................................13
4.1 Front Panel Features ........................................................................13
4.2 Rear Panel Features..........................................................................14
Chapter 5 Operation and Control ...............................................................17
5.1 Instructions on Control and Operation ...........................................17
5.2 Instructions on Parameter Settings.................................................18
5.2.1 Parameter Settings .........................................................................18
5.2.2 Menu Items.....................................................................................19
5.3 LED Indicator.....................................................................................21
5.4 HDMI Input/Output Module ...............................................................23
5.4.1 Installation ......................................................................................23
5.4.2 Network Control..............................................................................24
Chapter 6 Specifications .............................................................................27
Chapter 7 Appendix .....................................................................................31
7.1 AFD in 4:3 Mode ................................................................................31
7.2 AFD in 16:9 Mode ..............................................................................32
7.3 Converting from 4:3 to 16:9..............................................................33
7.4 Converting from 16:9 to 4:3..............................................................35

Product Overview
1
Chapter 1 Product Overview
This article is mainly about HCC6830N series models, which are HD/SD digital
signal cross converter that can be installed in 6800N series frame.
HCC6830N series models are high- integrated, they are the platform for
synchronizing and converting between HD and SD signals, and processing HD
and SD signals to mixed signals. They support signal cross converting and
AFD control. They use the advanced dynamic interlace analysis technology to
achieve high-quality video, and achieve the converting among various formats
video signals.
HCC6830N Series HD/SD Digital Video Signal Cross Converter support one
HDMI input, two SD-SDI output which have been cross converted and one
video loop output with clock recovery.
Figure 1-1 The Module of HCC6830N/HCC6830NS
HCC6830N/ HCC6830NS models support the following features:
Features
synchronous frame and cross conversion (only HCC6830NS has this
feature)
converting HD/SD-SDI input signals
using the advanced dynamic interlace analysis technology to achieve
high-quality video
ARC: automatic, using AFD(SMPTE-2016)
build-in framelock function and adjustment (only HCC6830NS model
has the framelock function)
build-in black field signal generator
build-in color corrector
Functionality

Product Overview
2
process or convert the auxiliary data, such as CC(608/708) and time
code (LTC、VITC)
alarm when video lost, static frame or detecting black field
supports SNMP for native and remote users to configure models
GPIO used to pre-set and parameter selection
Product Model
Table 1-1 Introduction of HCC6830N/ HCC6830N
Model Type
Description
HCC6830N
HCC6830N Series HD/SD Digital Video Signal Cross Converter,
supports HD/SD-SDI/HDMI.
HCC6830NS
HCC6830N Series HD/SD Digital Video Signal Cross Converter,
supports HD/SD-SDI/HDMI and frame synchronization.
The HCC6830N series models will support 3G video signals after
upgrading by getting the authorization code which is as a selection. Using
the authorization code to upgrade the module by WEB.
The HCC6830N series models will support one HDMI output by mounting a
HDMI input/output module as a selection.

Product Overview
3
Table 1-2 Input/Output Signals Supported by HCC6830N/ HCC6830NS
Model Type
Input
Output
HCC6830N
one adaptive HD/SD-SDI video
input
one HDMI input(achieved when
selecting HDMI input&output
module)
two HD-SDI output of cross
converted
Video loop output with clock
recovery
one HDMI output(achieved when
selecting HDMI input&output
module)
HCC6830NS
one adaptive HD/SD-SDI video
input
one HDMI input (achieved when
selecting HDMI input&output
module)
two HD-SDI output of cross
converted with synchronous frame
Video loop output with clock
recovery
one HDMI output (achieved when
selecting HDMI input&output
module)
Signal Flow Chart
The signal flow chart for this unit is shown as in Figure 1-2:
HDMI
Receiver
HDMI IN Video
Scaler
Color
Space
Conver
Generate
MUX
AUDIO
ANC
MUX
SDI
Trans
SDI
Driver
Audio SIP HDMI
Trans
EQ SDI
Receiver
Genlock
Audio anc
demux Loop out
SDI IN
REF IN
HDMI OUT
SDI OUT
SDI OUT
SDI OUT
Figure 1-2 The Signal Flow Chart of HCC6830N/HCC6830NS

4

Safety
5
Chapter 2 Safety
FCC Caution:
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Safety
6
Warnings:
Read, keep and follow all of these instructions for your safety. Heed all
warnings.
Converter
Upgrading of the converter is subject to change without notice.。
Contact your Customer Service representative if parts are missing or
damaged.
Position
Do not block any ventilation openings.
Do not use this unit near water.
Do not expose the unit to rain or moisture.
Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that product heat.
A nameplate indicating operating voltage, etc., is located on the rear
panel.
The socket-outlet shall be installed near the equipment and shall be
easily accessible.

Unpack and Installation
7
Chapter 3 Unpack and Installation
Unpack
When unpacking the components of this converter, please verify that none of
the components listed in Table 3-1 are damaged or lack. If there is any missing,
contact your distributors or OSEE for it.
Table 3-1 Packing List
No.
Item
Quantity
Comments
1
Converter
1
HCC6830N/HCC6830NS
2
Interface board
1
3
Attachments
1
4
User manual
1
5
warranty card
1
About Unpacking and Shipping
This product was carefully inspected, tested, and calibrated before
shipment to ensure years of stable and trouble-free service. Before
you install this unit, do the followings:
Check the equipment for any visible damage that may have
occurred during transit.
Confirm receipt of all items on the packing list.
Contact your dealer if any item on the packing list is missing.
Contact the carrier if any item is damaged.
Remove all packaging material from the product before you install
the unit.
Retain at least one set of the original packaging materials, in the
event that you need to return a product for servicing.

Unpack and Installation
8
If the original package is not available, you can supply your own
packaging as long as it meets the following criteria:
The packaging must be able to withstand the product’s weight.
The product must be held rigid within the packaging
There must be at least 5 cm of space between the product and the
container.
The corners of the product must be protected.
Ship products back to us for servicing prepaid and, if possible, in the
original packaging material. If the product is still within the warranty
period, we will return the product prepaid after servicing.
Installation
1. Prepare for installation
Make sure you have prepared the followings before mount the converter:
Inspect for any apparent physical damage that may have occurred in
transit.
Make sure you have received all the components listed in packing list.
if there are any anti-static package or other packages, please take off
them.
Keep the package in case of future usage.
The safety matters or operations that user must pay attention to when using
this product.
Check out the consumption of model and the maximum power of frame
before installation, The maximum power ratings for different frames are
shown as in Table 3-2.
Ensure that all handling precautions are taken to avoid electrostatic
discharge or other damage to sensitive electronic components. Wear an
earth strap and perform all PCB assembly at an appropriate anti-static work

Unpack and Installation
9
station. Follow the instructions carefully to fit the models.
Table 3-2 Maximum Power Ratings for 6800N Series Frames
Frame
Maximum Voltage
Redundant Power
Supplies
Numbers of Slots
6800N-C1
40W
Yes
4
6800N-C2
60W
Yes
10
2. Install the module
Follow the following steps to install the module:
Step 1 Install a back connector
First, install the back connector at the rear of the frame. Locate the
position for back connector and insert the back connector along the
slot, as shown in Figure 3-1 and Figure 3-2.
Figure 3-1 Rear Panel-Insert the Back Connector
Figure 3-2 Rear Panel-Fix the Back Connector

Unpack and Installation
10
Step 2 Fasten the screw to fix the back connector, as shown in Figure
3-3.
Figure 3-3 Rear Panel-Fasten the Back Connector
Step 3 Locate the slot for module, as shown in Figure 3-4.
Figure 3-4 Front Panel-Push the Module into the Slot
Step 4 Get the module installed in the slot.
Then, push the module slightly along the slot, press module again
to confirm that the module is installed firmly and then close swivel
handle, as shown in Figure 3-5.
Figure 3-5 Front Panel-Close the Swivel Handle of the Module

Unpack and Installation
11
Step 5 Install the front panel.
At last, install the front panel of the frame, as shown in Figure 3-6.
Figure 3-6 Front Panel-Install the Front Panle
Uninstallation
Follow the following steps to remove the module:
Step 1 Remove the front panel of the frame.
Step 2 Loosen and take off the module
Press down the swivel handle to loosen the module, as shown in
Figure 3-7.
Figure 3-7 Press Down the Swivel Handle
Then, hold the swivel handle, and pull out the module along the slot
of the frame.
Step 3 Install the front panel.
Take off the module, and mount the front panel on the frame.
Step 4 Take off the back connector
Unscrew the screws of the back connector, and take off the back
connector.

12

Features
13
Chapter 4 Features
4.1 Front Panel Features
The control switches and the LED indicator lights of HCC6830N series
modules are shown as in Figure 4-1:
1
2
3
Figure 4-1 The Switches and LED Lights of HCC6830N/HCC6830NS
1. Rotary switch
It is a rotary switch which has 16 positions coded from 0 to F, it is used to
select and point to a parameter item.
2. Toggle switch
It is a toggle switch which has 3 positions which will get back to the middle
position automatically, It is used to set the parameter value which has
been selected by SW1 through toggling up or down the handle.
3. LED Indicator
It shows the basic information of the module, refer to “5.3 LED Indicator”
for details.
Refer to “Chapter 5 Operation and Control”for the operation instructions of the
switches and LED indicators.

Features
14
4.2 Rear Panel Features
1. Illustration for back connector
We provide a HDMI input&output module to support HDMI input and
output function for HCC6830N/ HCC6830NS module. There are two kinds
of back connector for this function, the back connectors are shown as in
Figure 4-2:
Figure 4-2 The Back Connector of HCC6830N/HCC6830NS
The interfaces on the back connector of HCC6830N/HCC6830NS are
shown as Table 4-1:
Table 4-1 The interfaces on the Back Connector
Interface
Description
HDMI OUT
HDMI output
HDMI IN
HDMI input
SDI IN
HD/SD-SDI input
SDI OUT 1
HD/SD-SDI output 1
SDI OUT 2
HD/SD-SDI output 2
LOOP
Video loop output with clock recovery
REF IN
Reference input(only HCC6830NS has this interface)
GPI
Reserved