Outdoor Furniture Plus Double Cozi-Back Glider Firmware update

FM - 38
#PCTG2400, #PZTG2400
Firmly tap bolts into pre-drilled
holes before tightening.
CORRECT INCORRECT
1 2 34 5
Use to measure bolts
Double Cozi-Back Glider
Assembly Directions for
Double Gliders
Left Arm
Right Arm
Seat Slat
Cross Support
Leg
Base
Back Slat
Seat
Support
Hardware Package
2 ¼" x 4½" Carriage Bolts
2 ¼" x 3½" Carriage Bolts
7 ¼" x 3" Carriage Bolts
8 " x 2½" Carriage Bolts
8 " Lock Nuts
8 " Flange Nuts
18 ¼" Flange Nuts
4 " Acorn Nuts
4 Glider Brackets
Package contents
2 Bases
1 Back
1 Seat
1 Hardware Package
2 Arms with Legs
2 Cross Supports
4 Stops
1 Glider Bracket Package
tools needed:
Hammer
" Wrench
½" Wrench
Double Comfo-Back Glider

FM - 39
STEP #1 - Fasten the Arm and Leg Assembly to the
Seat and Back using 3- ¼" Carriage Bolts.
Using a hammer, rmly tap the Bolts until
they are ush with the poly surface. Securely
tighten using 3- ¼" Flange Nuts.
STEP #3 - Using 4- " x 2½" Carriage Bolts, place
them into the pre-drilled holes and tighten
using 4- " Flange Nuts. (Ensure the
Bolts are pointing inwards.)
STEP #4 - Place the 4- Glider Brackets onto the
Carriage Bolts and secure using 4- "
Lock Nuts (see inset). Be careful not to cross
thread the Lock Nuts.
STEP #2 - Turn the chair on the other side and repeat
Step #1.
¼" x 3½" Carriage Bolt
¼" x 3½" Carriage Bolt
¼" x 4½" Carriage Bolt
¼" x 4½" Carriage Bolt
¼" x 3" Carriage Bolt
¼" x 3" Carriage Bolt
⁄" x 2½" Carriage Bolts
⁄" x 2½" Carriage Bolt
⁄" Lock Nut
⁄" Flange Nut
Glider Bracket
Assembly Directions for
Glider Chair

FM - 40
STEP #1 - Fasten the two Cross Supports to the Base
using 8- ¼" x 2" Carriage Bolts and 8- ¼"
Flange Nuts.
STEP #3 - Using 4- " x 2½" Carriage Bolts, place
them into the pre-drilled holes and secure
using 4- " Flange Nuts. (Ensure the
Bolts are pointing outward.)
STEP #2 - Attach the four Glider Stops to the Base
using 4- ¼" x 3" Carriage Bolts and 4- ¼"
Flange Nuts.
Assembly Directions for
Glider Base
¼" x 2" Carriage Bolts
¼" x 3" Carriage Bolts
⁄" x 2½" Carriage Bolts

FM - 41
STEP #1 - First slide the Glider Base
underneath the Glider Chair,
ensuring the correct end of the
base is pointed forward (see
photo). en lift the Glider
Brackets onto the " x 2½"
Carriage Bolts of the Glider Base.
Using 4- " Lock Nuts, secure
Glider Bracket onto the Bolt.
Last, using 4- " Acorn Nuts,
hand tighten on the bolt.
STEP #2 - Repeat Step #1 on the other side
of your Glider. Your Glider is
now complete!
Assembly Directions for
Glider Chair and Base
Firmly tap bolts into pre-drilled
holes before tightening.
CORRECT INCORRECT
1 2 34 5
Use to measure bolts
Glider Bracket Diagram
⁄" x 2½" Carriage Bolt
⁄" Lock Nut
⁄" Flange Nut
⁄" Acorn Nut
Glider Bracket