Outdoor Furniture Plus PECC2131 Firmware update

FM - 44
#ESCC2131, #ESBC2135, #ZSCC2131, #ZSBC2135
Hardware Package
2 ¼" x 2¼" Carriage Bolts
6 ¼" x 3½" Carriage Bolts
12 ¼" Flange Nuts
4 ¼" x ¾" Machine Bolts
Package contents
1 Back
1 Seat
1 Base (in separate box)
2 Arm Assemblies
1 Swivel (in base box)
tools needed:
Hammer
" Wrench
Firmly tap bolts into pre-drilled
holes before tightening.
CORRECT INCORRECT
1 2 34 5
Use to measure bolts
Cozi-Back Swivel Chair
Assembly Directions for
Swivel Chairs
Seat Slat
Right Arm
Left Arm
Leg
Curved Seat Slat
Back Leg
Front Leg
Footrest
Back Slat

FM - 45
STEP #2 - A. Attach the seat to the back using
1- ¼" x 3½" Carriage Bolt and Flange
Nuts.
B. Attach the arm assembly to the Seat
and Back using 2- ¼" x 3½" and 1- ¼" x
2¼" Carriage Bolts and Flange Nuts.
STEP #1 - Fasten Swivel to aluminum frame using
4- ¼" x ¾" Machine Bolts and Flange Nuts.
STEP #3 - Turn chair on other side and repeat
Step 2.
STEP #4 - Lift the chair and set the Swivel Stem into the
receiver of the Base. Push rmly on the chair
until it sits securely in the receiver.
Your Swivel Chair is complete!
¼" x 3½" Carriage Bolts
¼" x 3½" Carriage Bolts
¼" x ¾" Machine Bolts
¼" x 3½" Carriage Bolts
¼" x 3½" Carriage Bolts
¼" x 2¼" Carriage Bolts
¼" x 2¼" Carriage Bolts
A.
A.
B.
B.
B.
B.

FM - 72
#GCIT4472D, #GCIT4472C, #GCIT4472B
in Garden Classic Collection
HARDWARE PACKAGE
16 ¼" x 2" Carriage Bolts
16 ¼" Flange Nuts
2 Umbrella Knobs
44 3" Screws
24 1½" Screws
PACKAGE CONTENTS
1Top
4 Bases
4 Long Cross Supports
2 Short Cross Supports
4 Footrests (Bar and Counter Height)
1 Umbrella Holder
1 Umbrella Plug
8 Braces
1 Hardware Package
TOOLS NEEDED:
Hammer
7/" Wrench
Cordless Drill/Screwdriver
Firmly tap bolts into pre-drilled
holes before tightening.
CORRECT INCORRECT
1 2 34 5
Use to measure bolts
Garden Classic Table
NOTE: Bar
and Counter
Height Only
Assembly Directions for
44"x72" Rectangular Table
Be sure to
use 1½"
screws when
fastening
braces.
!
Base
Long Cross Support
Short Cross Support
Upright
Top Boards
Apron
Brace
Umbrella
Holder
Curved End Board
Footrest
Garden Classic
Table

FM - 73
STEP #1 - First assemble both Bases and Long Cross
Supports using 3" Screws.
Please note: ere are two outside Bases and
two center Bases. e two center Bases have
extra mortises for the Umbrella Holder and
Short Cross Supports (see Step #3).
STEP #2 - Attach the rst Base Assembly to the
aluminum frame of the Top using
8- ¼" x 2" Carriage Bolts.
STEP #3 - Attach the two Short Cross Supports and the
Umbrella Holder to the Base using 3" Screws.
STEP #4 - First attach the second Base Assembly to the
aluminum Frame of the Top using 8- ¼" x 2"
Carriage Bolts. Second fasten the Base
Assembly to the Short Cross Pieces and
Umbrella Holder using 3" Screws.
STEP #5 - Last, attach the Braces to the Top and the Base
using 1½" Screws.
Caution: Do not overtighten the Screws into
the Top!
Umbrella
Knobs
¼" x 2" Carriage Bolts
3" Screws
3" Screws
3" Screws
¼" x 2" Carriage Bolts
Footrest
1½" Screws (circled)
Cross Support