Outsunny 840-193 840-193V01 Installation guide

ASSEMBLY & INSTRUCTION MANUAL
IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY
INboa011V04_US_UK
840-193_840-193V01
Assembly video please scan the QR code .

1

2

3
1 1 2-1 1 2-3 1 3 1
5 1 4-1 1 4-3 1 6-1 1
6-3 1 7 1 8 1 9 1
10 2
11 2 12 4
13-1 1 14 1 13-2 1
15 16
16 3
18 2 19 2
17-1 1 17-2 1
20 4
21 1 22 1
23 4

4
5
315
15 7

5
Step 1: Roller assembly
Keep the rollers aligned, assemble the roller with the connectors and secure it with
the corresponding bolts as figure below:
Step 2: Torsion bar and arm assembly:
keep the four face aligned , connect the torsion bar with the connectors and secure it
with the corresponding bolts as figure below:
Then assembly the arm to the torsion bar as figure below.Two arms need in the
same direction, the rope of arm cannot be unlocked until the whole assembly are
complete.
L1:14CM
L2:9CM

6
Step 4: Front bar wrist support assembly:
Slide the front bar feet into the front bar without tightening.As shown in the figure
below:
Step3: Front bar assembly
Connect the front bar with connectors and secure it with the corresponding bolts as
figure below:.(please keep the front bar aligned).

7
Step 6: Link the self-locking nut
Link the self-locking nut into screw which at the bottom of the screw in front bar feet
by a wrench, stop when the thread:leakage 1 ~ 2 laps.As shown in the figure below:
Step 5: Arms with front bar assembly:
Put front bar feet bolt through the hole of small arm, then position the front bar.After
positioning, tighten the nut with wrencn, as tigure below:
ATTENTION: BEFORE BLOCKING THE NUT.ENSURE THAT THE ARMS ARE
PROPERLY ALIGNED.

8
Step 8: Fabric and valance assembly:
Open the fabric bag, Spread out both fabric 14A and valance 14B and use the cloth
guiding wire to line through the fabric.As shown in the figure below:
Step7: Left roller support with gear box assembly:
Hammer the left roller support with gear box into the left end of torsion bar by wood
hammer, then tighten the left hexagon bolt by 5mm. As shown in the figure below:

9
Step 10:
One end of fabric through the groove of front bar,well-distributed the fabric after pull
in all fabric, then insert shaft of roller into the square hole of gear case.As shown in
the figure below,
Step 9: Roll in the fabric on the roller
Roll in the fabric on the roller, pay attention to the fabric direction needed, as shown
in the figure below:
Please face up the fabric when assembling.Keep the same spacing X at both ends.
Spread the fabric slowly in case of damage.
lf the part of front bar is a little deformed, please adjust it with tools by yourself.

10
Step 12: Assemble to make a whole awning
Make the valance through groove of front bar, pay attention to the direction and
make sure the left and right sides on average, then hitting the cover of front bar into
end of front bar. As shown in the figure below:
Step 11: Right roller support assembly:
Insert the shaft of roller into roll tube plug，meanwhile insert the torsion bar into the
right roller supports with hitting. Then tighten the right hexagon bolt by 5mm
Hexagon wrench.As shown in the figure below:
lf the part of front bar is a little deformed, please adjust it with tools by yourself.

11
10 11 23 12 9
8'-13'

12
8"(20.5cm)
8-13 '(2.5-4m).

13
< 10.8'(3.5m)
10.8-14'(3.5-4m)
≥3.9"(10cm)
≥3.9"(10cm)

14
“
3.15"(8cm)
0.55"(14mm)

15
0.75"(19mm)

16

17