oventrop Regtronic RH HT Operating instructions

*11213758* 11213758
Valves, controls + systems
“Regtronic RH HT”
Installation and operating instructions for the specialised installer
EN
Please read this manual carefully to get the best performance from this unit.
Please keep this manual carefully.

en
2
© 20201105_11213758_Oventrop_Regtronic_RH_HT.monen.indd
Safety advice
Please pay attention to the following safety advice in order to avoid danger and
damage to people and property.
Instructions
Attention must be paid to the valid local standards, regulations and directives!
Information about the product
Proper usage
The controller is designed for use in heating systems in compliance with the tech-
nical data specied in this manual.
Improper use excludes all liability claims.
CE Declaration of conformity
The product complies with the relevant directives and is therefore
labelled with the CE mark.
Note
Strong electromagnetic elds can impair the function of the controller.
ÎMake sure the controller as well as the system are not exposed to
strong electromagnetic elds.
Subject to technical change. Errors excepted.
Target group
These instructions are exclusively addressed to authorised skilled personnel.
Only qualied electricians should carry out electrical works.
Initial commissioning must be effected by the system installer or qualied person-
nel named by the system installer.
Description of symbols
WARNING! Warnings are indicated with a warning triangle!
ÎThey contain information on how to avoid the dan-
ger described.
Signal words describe the danger that may occur, when it is not avoided.
• WARNING means that injury, possibly life-threatening injury, can occur.
• ATTENTION means that damage to the appliance can occur.
Note
Notes are indicated with an information symbol.
ÎArrows indicate instruction steps that should be carried out.
Disposal
• Dispose of the packaging in an environmentally sound manner.
• At the end of its working life, the product must not be disposed of as
urban waste. Old appliances must be disposed of by an authorised body
in an environmentally sound manner. Upon request we will take back
your old appliances bought from us and guarantee an environmentally
sound disposal of the devices.

en
3
Contents
Navigator
Installation page 5
For mounting and connecting the controller, see page 5.
Commissioning page 13
For commissioning the controller, see page 13.
Settings page 15
For making adjustments in the main and additional functions (including chimney sweep-
er and screed drying), see page 15.
Data communication page 44
For establishing communication to the controller, see page 44.
Troubleshooting page 49
When an error has occurred, see page 49 for diagnostics and troubleshooting.
1 Overview ........................................................................................... 4
2 Installation ........................................................................................ 5
2.1 Mounting .....................................................................................................................5
2.2 Electrical connection ................................................................................................5
2.3 Data communication / Bus .......................................................................................7
2.4 SD card slot................................................................................................................7
3 Operation and function ................................................................... 8
3.1 Buttons ........................................................................................................................8
3.2 Selecting menu points and adjusting values ........................................................8
4 Commissioning............................................................................... 13
4.1 Schemes with basic settings................................................................................. 15
4.2 Step-by-step parameterisation ............................................................................ 15
5 Functions and options.................................................................... 16
5.1 Menu structure ....................................................................................................... 16
5.2 Status menu ............................................................................................................. 17
5.3 Heating...................................................................................................................... 17
5.4 Arrangement ........................................................................................................... 17
5.5 HQM ......................................................................................................................... 17
5.6 Meas./ Balance values ............................................................................................. 18
5.7 Messages................................................................................................................... 18
6 Heating............................................................................................ 18
6.1 Shared relays............................................................................................................ 18
6.2 Heating circuits ....................................................................................................... 21
6.3 Optional functions ................................................................................................. 29
Regtronic RH HT
7 Arrangement .................................................................................. 35
7.1 Optional functions ................................................................................................. 35
8 HQM ................................................................................................ 42
9 Basic settings .................................................................................. 43
10 SD card ........................................................................................... 44
11 Manual mode ................................................................................. 45
12 User code ....................................................................................... 45
13.2 Inputs......................................................................................................................... 46
13 In- / Outputs..................................................................................... 46
13.1 Modules .................................................................................................................... 46
13.3 Outputs .................................................................................................................... 47
14 Troubleshooting / frequently asked questions .............................. 49
15 Index ................................................................................................ 52

en
4
1 Overview
• Extra large graphic display
• 5 relay outputs
• 8 (9) inputs for Pt1000, Pt500 or KTY temperature sensors (system
dependent)
• 2 inputs for digital Grundfos Direct Sensors™
• 2PWMoutputsforspeedcontrolofhigh-efciencypumps
• Datalogging/rmwareupdatesviaSDmemorycard
• Pre-programmed basic systems
• 1 mixed heating circuit, 1 unmixed heating circuit
• Pre-programmed optional functions
• DHW heating
• Circulation
• Thermal disinfection
• S-Bus
• Energy-efcientswitching-modepowersupply
• Modulating heating control with 0-10V boiler control
• Weather-compensatedcontrolwithroominuenceorde-
mand-based room control with up to 5 room temperature sensors
• Remote access with a room control unit
170
198
43
Technical data
Inputs: 8 (9) inputs for Pt1000,Pt500, or KTY temperature sensors (can optionally
be used for remote controls), 1 impulse input V40, inputs for 2 digital Grundfos
Direct Sensors™, 1 input for an irradiation sensor
Outputs: 2 semiconductor relays, 2 electromechanical relays, 1 potential-free
relay, 2 PWM outputs, 24 V output
PWM frequency: 1000 Hz
PWM voltage: 10.5 V
Switching capacity:
1 (1) A 240 V~ (semiconductor relay)
4 (2) A 240 V~ (electromechanical relay)
4 (1) A 240 V⎓(potential-free relay)
4 (1) A 24 V ⎓(potential-free relay)
Total switching capacity: 4 A 240 V~
Power supply: 100 – 240 V~ (50 – 60 Hz)
Supply connection: type Y attachment
Standby: 1.55 W
Temperature controls class: VIII
Energyefciencycontribution:5 %
Mode of operation: type 1.B.C.Y action
Rated impulse voltage: 2.5 kV
Data interface: S-Bus, SD card slot
S-Bus current supply: 60 mA
Functions: screed drying, weather-compensated heating circuit control, backup
heating,DHW heating with priority logic, circulation, thermal disinfection, heat quan-
tity measurement, optional functions such as solid fuel boiler, return preheating, etc.
Housing: plastic, PC-ABS and PMMA
Mounting: wall mounting, also suitable for mounting into patch panels
Indication / Display: full graphic display, operating control LED (directional pad)
and background illumination
Operation: 7 buttons at the front of the housing
Protection type: IP 20 / DIN EN 60529
Protection class: I
Ambient temperature: 0 … 50 °C
Degree of pollution: 2
Dimensions: 198 x 170 x 43 mm

Installation
5
CommissioningSettingsTroubleshooting Data communication en
2 Installation
2.1 Mounting
WARNING! Electric shock!
Upon opening the housing, live parts are exposed!
ÎAlways disconnect the device from power supply
before opening the housing!
Note
Strong electromagnetic elds can impair the function of the device.
ÎMake sure the device as well as the system are not exposed to
strong electromagnetic elds.
The unit must only be located in dry interior rooms.
The controller must additionally be supplied from a double pole switch with con-
tact gap of at least 3 mm.
Please pay attention to separate routing of sensor cables and mains cables.
In order to mount the device to the wall, carry out the following steps:
ÎUnscrew the cross-head screw from the cover and remove it along with the
cover from the housing.
ÎMark the upper fastening point on the wall. Drill and fasten the enclosed wall
plug and screw leaving the head protruding.
ÎHang the housing from the upper fastening point and mark the lower fasten-
ing points (centres 150 mm).
ÎInsert lower wall plugs.
ÎFasten the housing to the wall with the lower fastening screw and tighten.
ÎCarry out the electrical wiring in accordance with the terminal allocation
(see page 6).
ÎPut the cover on the housing.
ÎAttach with the fastening screw.
upper fastening point
lower fastening point
cover
screw
2.2 Electrical connection
WARNING! Electric shock!
Upon opening the housing, live parts are exposed!
ÎAlways disconnect the device from power supply
before opening the housing!
ATTENTION! ESD damage!
Electrostatic discharge can lead to damage to electronic
components!
ÎTake care to discharge properly before touching
the inside of the device!To do so, touch a grounded
surface such as a radiator or tap!
Note
Connecting the device to the power supply must always be the last step
of the installation!
Note:
The pump speed must be set to 100% when auxiliary relays or valves
are connected.

6
Installation Commissioning Settings Data communication Troubleshooting
en
R2,R3 1 (1) A (100 – 240) V~
R1,R4 4 (2) A (100 – 240) V~
4 (1) A 240 V~
4 (1) A 24V
R5
S-Bus
S-Bus GND
S1 S2 S3 S4 S5 S6 S7 S8
R4 R5
R5
N
100 – 240 V~
50 – 60 Hz
T4A
R3 R2 R1
L' L
GND
Temp. Sensor
0-10V/PWM
A B
RPD
Isolate mains before removing cover!
Vor Öffnen Gerät spannungslos schalten!
Use ground common terminal block
Masse-Sammelklemme benutzen
Use neutral conductor common terminal block
Neutralleiter-Sammelklemme benutzen!
Use PE Common terminal block
Schutzleiter-Sammelklemme benutzen
VFD
CS10 V40/S9
DE-59939 Olsberg
Regtronic RH HT
VN: 2.2
B GND
24 V
IP20
N
input for Grundfos
Direct Sensors™
potential-free
relay
sensor ground common
terminal block
sensor terminals
protective conductor
common terminal block (PE)
neutral conductor
common terminal
block
0-10V (PWM)
terminals
S-Bus
Depending on the product version, cables are already connected to the device. If
that is not the case, please proceed as follows:
The controller is equipped with 5 relays in total to which loads such as pumps,
valves, etc. can be connected:
Relays 1 and 4 are electromechanical relays.
Relays 2 and 3 are semiconductor relays, designed for pump speed control.
Conductor R1 … R4
Neutral conductor N (common terminal block)
Protective earth conductor ⏚(common terminal block)
Relay 5 is a potential-free relay:
The connection to R5 can be made with either polarity.
The connector marked 24 V is used for connecting the actuator for the trans-
mission station.
The temperature sensors (S1 to S8) have to be connected to the terminals
S1 … S8 and GND (either polarity).
The terminal S9 can be used as an impulse input for an impulse ow rate sensor
or as an input for a ow switch.
An impulse ow rate sensor can be connected to the terminals S9 / V40 and GND
(either polarity).
Connect the irradiation sensor to the terminals CS10 and GND with correct
polarity.To do so, connect the cable marked GND to the GND common terminal
block, the cable marked CS to the terminal marked CS10.
In the menu, the irradiation sensor will be indicated as CS10.
The connector marked PWM / 0-10V contains the 2 PWM / 0-10 V control signal
outputs for high-efciency pumps or the 0-10 V boiler control respectively.
2 4
1 3
R1-R4 1 (1) A (100 ... 240) V~
4 (1) A 240 V~
4 (1) A 24V
R5
S-Bus
S-Bus GND
S1 S2 S3 S4 S5 S6 S7 S8
R4 R5
IP20
R5
N
100 ... 240 V~
50-60 Hz
T4A
R3 R2 R1
L' L
GND
Temp. Sensor
0-10V/PWM
A B
RPD
N
Isolate mains before removing cover!
Vor Öffnen Gerät spannungslos schalten!
Use ground common terminal block
Masse-Sammelklemme benutzen
Use neutral conductor common terminal block
Neutralleiter-Sammelklemme benutzen!
Use PE Common terminal block
Schutzleiter-Sammelklemme benutzen
VFD
CS10 V40/S9
1 = output A, control signal
2 = output A, GND
3 = output B, GND
4 = output B, control signal
In the In-/Outputs menu, relays can be allocated to the PWM outputs.
Connect the digital Grundfos Direct Sensors™ to theVFD and RPD inputs.
The controller is supplied with power via a mains cable.The power supply of the
device must be 100– 240 V~ (50 – 60 Hz).
The mains connection is to be made at the following terminals:
Neutral conductor N
Conductor L
Protective earth conductor ⏚(common terminal block)
WARNING! Electric shock!
L' is a fused contact permanently carrying voltage.
ÎAlways disconnect the device from power supply be-
fore opening the housing!
Conductor L' (L' is not connected with the mains cable. L' is a fused contact
permanently carrying voltage.)
Note
For more details about the commissioning procedure see page 13.
24 V terminal

Installation
7
CommissioningSettingsTroubleshooting Data communication en
Power relay
WARNING! Electric shock!
Upon opening the housing, live parts are exposed!
ÎAlways disconnect the device from power supply
before opening the housing!
230V~
13
24
A1
A2
20A 250V~
R2
Regtronic RH
Mains plug 230 V~
Pump
Power relay Art.-No.: 1152089
e. g. Regtronic RH
Relay output R2, R3
Grounding conductor
common terminal block
PE ⌯
brown
green / yellow
green / yellow
brown
brown
blue
blue
blue
Relay output
Relays 1 and 4 are electromechanical relays for loads with high current consump-
tion. If loads with high current consumption are to be connected to relay 2 and /
or 3, pay attention to the following note:
Note:
The following pumps have to be controlled over the power relay:
• Pumps with a nominal current > 1A (see indication on the type label of
the pump)
• Pumps listed in the following:
e. g. Grundfos Magna 3,Wilo Stratos 50/1-12,Wilo Stratos 40/1-8,
KSB Calio 30-120
2.3 Data communication / Bus
The controller is equipped with the S-Bus for data transfer with external mod-
ules.The connection is carried out at the two terminals marked S-Bus and GND
(either polarity). One or more S-Bus modules can be connected via this data bus,
such as:
• CS-BS1 Communication module
• CS-BS6 Datalogger
• EM Extension module
2.4 SD card slot
The controller is equipped with an SD card slot.
With an SD card, the following functions can be carried out:
• Store measurement and balance values onto the SD card.After the transfer to a
computer, the values can be opened and visualised, e. g. in a spreadsheet.
• Prepare adjustments and parameterisations on a computer and transfer them
via the SD card.
• Store adjustments and parameterisations on the SD card and, if necessary, re-
trieve them from there.
• Download rmware updates from the Internet and install them on the con-
troller.
For more information about using an SD card, see page 44.

8
Installation Commissioning Settings Data communication Troubleshooting
en
3.2 Selecting menu points and adjusting values
During normal operation of the controller, the display is in the Status menu. If no
button is pressed for a few seconds, the display illumination goes out.
Press any key to reactivate the display illumination.
ÎIn order to scroll through a menu or to adjust a value, press either buttons ❶
and ❸or buttons ❷and ❹.
ÎTo open a sub-menu or to conrm a value, press button ➄.
ÎTo re-enter the status menu, press button ➅ – unconrmed adjustments will
not be saved.
ÎTo enter the previous menu, press button ➆ – unconrmed adjustments will
not be saved.
Use the buttons ❷and ❹for scrolling through the status menu.
❷
❹
With the parameters Mixer and HC pump in the status menu of the heating
circuits, a shortcut to the Manual mode is possible, for example, for carrying
out a mixer test.
ÎIn order to enter the Manual mode, press button ➄.
ÎIn order to get back to the status menu of the heating circuit, press button ➆.
If no button has been pressed within a couple of minutes, the adjustment is can-
celled and the previous value is retained.
Note:
After having carried out the adjustments, the controller has to be kept
switched-on for at least 2 min for storing the adjustments.
Chimney sweeper / screed drying
The chimney sweeper or screed drying function can be triggered with the button
➅.The chimney sweeper function is activated by default. In order to activate the
screed drying function, the chimney sweeper function must be deactivated in all
heating circuits (see page 26).
ÎIn order to trigger the chimney sweeper or screed drying function, press and
hold down button ➅for 5 s.
3 Operation and function
3.1 Buttons
The controller is operated via the 7 buttons next to the display. They have the
following functions:
Button ❶- scrolling upwards
Button ❸- scrolling downwards
Button ❷- increasing adjustment values
Button ❹- reducing adjustment values
Button ➄ - conrming
Button ➅- entering the status menu/ chimney sweeper mode or screed drying
mode (system-dependent)
Button ➆- escape button for changing into the previous menu
1
2
4
63
5
7
Operating control LED (in the directional pad)
Green: Everything OK
Red: Error / cancellation screed drying
Red ashing: Sensor fault, initialisation
Green ashing: Manual mode

Installation
9
CommissioningSettingsTroubleshooting Data communication en
If the symbol ⏩is shown behind a menu item, pressing button ➄will open a
new sub-menu.
The symbolat the edge of the display next to a sensor allocated to a function,
means that this sensor has several functions. Use buttons ❷and ❹to scroll to
these functions.
If the symbol ➕is shown in front of a menu item, pressing button ➄will open a
new sub-menu. If it is already opened, a ➖is shown instead of the ➕.
current value savedminimum value maximum value
adjusted value (not
yet conrmed)
adjustment
channel
Values and adjustments can be changed in different ways:
Numeric values can be adjusted by means of a slide bar. The minimum value is
indicated to the left, the maximum value to the right.The large number above the
slide bar indicates the current adjustment.By pressing buttons ❷or ❹the upper
slide bar can be moved to the left or to the right.
Only after the adjustment has been conrmed by pressing button ➄will the
number below the slide bar indicate the new value.The new value will be saved if
it is conrmed by pressing button ➄again.
active area inactive area
When 2 values are locked against each other, they will display a reduced adjust-
ment range depending on the adjustment of the respective other value.
In this case, the active area of the slide bar is shortened, the inactive area is indi-
cated as a dotted line. The indication of the minimum and maximum values will
adapt to the reduction.
If only one item of several can be selected, they will be indicated with "radio
buttons". When one item has been selected, the radio button in front of it is lled.
If more than one item of several can be selected, they will be indicated with
checkboxes.When an item has been selected, an xappears inside the checkbox.

10
Installation Commissioning Settings Data communication Troubleshooting
en
Adjusting the timer
When the Timer option is activated, a timer is in-
dicated in which time frames for the function can be
adjusted.
In the Day selection channel, the days of the week
are available individually and as frequently selected
combinations.
If more than one day or combination is selected, they
will be merged into one combination for the follow-
ing steps.
The last menu item after the list of days is Contin-
ue. If Continue is selected, the timer menu opens, in
which the time frames can be adjusted.
Adding a time frame:
In order to add a time frame, proceed as follows:
ÎSelect New time frame.
ÎAdjust Start and Stop for the desired time
frame.
The time frames can be adjusted in steps of 5 min.
ÎIn order to save the time frame, select Save and
conrm the security enquiry with Ye s .
ÎIn order to add another time frame, repeat the
previous steps.
6 time frames can be adjusted per day or combi-
nation.
ÎPress button ➆in order to get back to the day
selection.

Installation
11
CommissioningSettingsTroubleshooting Data communication en
Copying a time frame:
In order to copy time frames already adjusted into
another day / another combination, proceed as fol-
lows:
ÎChoose the day /The combination into which the
time frames are to be copied and select Copy
from.
A selection of days and / or combinations with time
frames will appear.
ÎSelect the day or combination from which the
time frames are to be copied.
All time frames adjusted for the selected day or com-
bination will be copied.
If the time frames copied are not changed, the day or
combination will be added to the combination from
which the time frames have been copied.
Changing a time frame:
In order to change a time frame, proceed as follows:
ÎSelect the time frame to be changed.
ÎMake the desired change.
ÎIn order to save the time frame, select Save and
conrm the security enquiry with Ye s .
Removing a time frame:
In order to delete a time frame, proceed as follows:
ÎSelect the time frame that is to be deleted.
ÎSelect Delete and conrm the security enquiry
with Ye s .

12
Installation Commissioning Settings Data communication Troubleshooting
en
Resetting the timer:
In order to reset time frames adjusted for a certain
day or combination, proceed as follows
ÎSelect the desired day or combination.
The selected day or combination will disappear from
the list, all its time frames will be deleted.
In order to reset the whole timer, proceed as follows:
All adjustments made for the timer are deleted.
ÎSelect Reset and conrm the security enquiry
with Ye s .
ÎSelect Reset and conrm the security enquiry
with Ye s .

Installation
13
CommissioningSettingsTroubleshooting Data communication en
4 Commissioning
When the hydraulic system is lled and ready for operation, connect the control-
ler to the mains.
The controller runs an initialisation phase in which the directional pad ashes red.
When the controller is commissioned or when it is reset, it will run a commis-
sioning menu after the initialisation phase. The commissioning menu leads the
user through the most important adjustment channels needed for operating the
system.
Commissioning menu
The commissioning menu consists of the channels described in the following. In
order to make an adjustment, press button ➄. Adjust the value by pressing but-
tons ❷and ❹, then press button ➄ to conrm. The next channel will appear
in the display.
5
5
Adjustment mode
Button navigation
Changing a value
Conrming a value
Next parameter appears
automatically
2
4
1. Language:
ÎAdjust the desired menu language.
2. Units:
ÎAdjust the desired temperature unit.
ÎAdjust the desired volume unit.
ÎAdjust the desired pressure unit.
ÎAdjust the desired energy unit.

14
Installation Commissioning Settings Data communication Troubleshooting
en
4. Time:
ÎAdjust the clock time. First of all adjust the hours,
then the minutes.
5. Date:
ÎAdjust the date. First of all adjust the year, then
the month and then the day.
6. Basic system
ÎAdjust the desired scheme (heating circuit, de-
mand, DHW heating).
3. Daylight savings time adjustment:
ÎActivate or deactivate the automatic daylight sav-
ings time adjustment.
Note:
The adjustments carried out during commissioning can be changed any-
time in the corresponding adjustment channel.
Additional functions and options can also be activated or deactivated.
Set the code to the customer code before handing over the
controller to the customer (see page 45).
7. Completing the commissioning menu:
After the scheme has been selected, a security en-
quiry appears. If the security enquiry is conrmed, the
adjustments are saved.
ÎIn order to conrm the security enquiry, press
button ➄.
ÎIn order to get back to the commissioning menu
channels, press button ➆.
After you have conrmed the security enquiry, the
controller is ready for operation and normally the
factory settings will give close to optimum operation.

Installation
15
CommissioningSettingsTroubleshooting Data communication en
4.1 Schemes with basic settings
The controller is preprogrammed for several basic systems. The basic pre-ad-
justments have already been made. The selectable schemes can be found in the
appendix of the "Regudis H-HT" manual.
Relay and sensor allocations correspond to the gures.
Scheme 0 has no pre-adjustments.
4.2 Step-by-step parameterisation
The heating controller Regtronic RH is a controller that offers a broad variety of
functions to the user. At the same time, the user has a lot of freedom in congu-
rating them. Therefore, to set up a complex system, careful planning is required.
We recommend drawing a sketch of the system rst.
If planning, hydraulic construction and electrical connection have all been carried
out successfully, proceed as follows:
1. Running the commissioning menu
After the commissioning menu has been nished (see page 13), further adjust-
ments can be made.The commissioning menu can be repeated any time by means
of a reset (see page 43).Additional adjustments will be deleted.
2. Registering modules and sensors
If an impulse ow rate sensor, a switch, Grundfos Direct Sensors™ and/or ex-
ternal extension modules are connected, these have to be registered in the In-/
Outputs menu.
For further information about the registration of modules and sensors see page
46.
3. Adjusting heating circuits and activating optional heating functions
Now, further heating circuits can be activated and adjusted.
For the heating part of the arrangement, optional functions can be selected, acti-
vated and adjusted.
• DHW heating
• Circulation
• Thermal disinfection
Heating circuits and their optional functions can use shared relays for (boiler)
demands, loading pumps or valves.They have to be selected in the Shared relays
menu rst (see page 18). All free relays available on the controller and on the
modules connected can be used.
The controller always suggests the numerically smallest free relay.
Sensors can be allocated to more than one function.
For further information about heating circuits and optional heating functions see
page 29.
4. Adjusting the operating mode
After commissioning the heating circuit will be in automatic mode.The operating
mode can be changed in the status menu:
• Automatic
• Day
• Night
• Summer
• Holiday
• Off
The operating mode of the rst heating circuit also applies to all further heating
circuits (via extension modules), if they are linked. If you wish to operate one of
the heating circuits 2… 7 independently, deactivate the linking of the correspond-
ing heating circuit (see page 27).
5. Activating optional arrangement functions
Now, optional functions for the arrangement can be selected, activated and ad-
justed:
• Heat exchange
• Return preheating
• Solid fuel boiler
• Mixer
• Parallel relay
• Irradiation switch
• Zone loading
• Error relay
• Function block
Free relays can be allocated to optional functions which require a relay.The con-
troller always suggests the numerically smallest free relay.
Sensors can be allocated to more than one function.
For further information about the optional arrangement functions see page 35.

16
Installation Commissioning Settings Data communication Troubleshooting
en
Main menu
Status
Heating
Arrangement
HQM
Basic settings
SD card
Manual mode
User code
In- / Outputs
Arrangement
Optional functions
Optional functions
DHW heating
Th. Disinfection
Circulation
Transmission station
Heating
System
Shared relays
Heating circuits
Optional functions
Screed drying
The menu items and adjustment values
selectable are variable depending on ad-
justments already made. The gure only
shows an exemplary excerpt of the com-
plete menu in order to visualise the menu
structure.
Basic settings
Language
Temp. Unit
Flow Unit
Press. Unit
Energy Unit
Auto DST
Time
…
Scheme
Reset
In- / Outputs
Modules
Inputs
Outputs
5 Functions and options
5.1 Menu structure
Optional functions
Heat exchange
Return preheating
Solid fuel boiler
Mixer
Parallel relay
Irradiation switch
Zone loading
Error relay
Function block
Shared rel.
Demand 1
Demand 2
Pump 1
Pump 2
Valve 1
Valve 2
Demand 1
Relay
0-10 V
Minimum runtime

Installation
17
CommissioningSettingsTroubleshooting Data communication en
5.2 Status menu
The status menu contains information about the current states of all activated
heating circuits, optional functions and HQM. Furthermore, measured and balance
values as well as messages are indicated.
Use the buttons ❷and ❹for scrolling through the status menu.
❷
❹
5.3 Heating
In the Status / Heating menu, the status of the heating circuits activated as well
as of the selected optional functions is indicated.
The status of the rst heating circuit is also the home screen of the controller. In
this menu, the operating mode of the heating circuit can be changed:
Automatic:Automatic heating mode with optionally activated DHW heating and
circulation.
Day: Constant heating mode with the adjusted day correction.
Night: Constant heating mode with the adjusted night correction and the select-
ed correction mode.
Summer: The heating circuit is switched off.The optionally activated DHW heat-
ing and circulation remain active.
Off: The heating circuit as well as the optionally activated DHW heating and
circulation are switched off.
Holiday: Constant heating mode within an adjustable time frame with the adjust-
ed night correction and the selected correction mode.
If the operating mode Holiday is selected, the adjustment channel Holiday will
appear for adjusting the days of an absence.The day, on which the adjustment is
made, is the rst day of absence. The days will be counted backwards at 00:00. The
remaining days are indicated in the status menu (countdown). If 0 is reached, the
controller automatically switches to the operating mode Automatic.
The operating mode of the rst heating circuit also applies to all further heating
circuits (via extension modules), if they are linked. If you wish to operate one of
the heating circuits 2… 7 independently, deactivate the linking of the correspond-
ing heating circuit (see page 27).
5.4 Arrangement
In the Status /Arrangement menu, the status information (Active, Inactive, De-
activated), the temperatures of the relevant sensors and the relays states are
indicated.
5.5 HQM
In the Status / HQM menu, all current measured values of the ow and return
sensors, ow rate and power as well as heat quantity are indicated.

18
Installation Commissioning Settings Data communication Troubleshooting
en
5.6 Meas./ Balance values
In the Status / Meas./ Balance menu, all current measurement values as well as
a range of balance values are displayed. Some of the menu items can be selected
in order to enter a sub-menu.
Each sensor and relay is indicated with the component or function it has been
allocated to.The symbol ▶at the edge of the display next to a sensor allocated to
a function, means that this sensor has several functions. Use buttons ❷and ❹to
scroll to these functions.The sensors and relays of the controller and all modules
connected are listed in numerical order.
When a line with a measurement value is selected, another sub-menu will open.
If, for example, S1 is selected, a sub-menu indicating the minimum and maximum
values will open.
5.7 Messages
In the Status / Messages menu, error and warning messages are indicated.
During normal operation, the message Everything OK is indicated.
A line break or short circuit in a sensor line is indicated as !Sensor fault.A pre-
cise error code can be found in the Status / Meas.-/ Balance values menu.
6 Heating
In this menu, all adjustments for the heating part of the arrangement or for the
heating circuits respectively can be made.
Shared relays for demands, loading pumps or valves can be activated,heating circuits
can be congured and optional functions can be selected and adjusted.
In this menu, the screed drying function can be activated and adjusted.
6.1 Shared relays
In this menu, adjustments for heat generators, loading pumps and valves which
are shared by several heating circuits and their optional functions can be made.
Further options such as boiler protection, start-up and overrun are also available.
Shared relays will be available for selection under Virtual in the heating circuits
and in the relay allocation channels of the corresponding optional functions of the
Heating menu. This way, several heating circuits and optional functions (heating)
can demand the same heat source, use the same loading pump or switch a shared
relay (e. g. a valve).
Note:
Activate and adjust the shared relays rst. They will then be available in
the heating circuits and optional functions.

Installation
19
CommissioningSettingsTroubleshooting Data communication en
Heating / Shared rel.
Adjustment
channel Description Adjustment range /
selection Factory setting
Dem. 1 (2) Demand 1 (2) Activated, Deactivated Deactivated
Relay Relay option Yes, No No
Relay Relay sub-menu - -
Output Output selection system dependent R5
Boiler pr. min Option for boiler protection min Yes, No No
Tmin Minimum boiler temperature 10 … 90 °C 55 °C
Boiler pr. max Option for boiler protection max Yes, No No
Tmax Maximum boiler temperature 20 … 95 °C 90 °C
Sensor Boiler Boiler sensor selection system dependent S4
0-10 V 0-10 V option Yes, No No
0-10 V 0-10 V sub-menu - -
Output Output selection -, A, B D
Tset 1 Lower boiler temperature 10 … 90 °C 10 °C
Volt 1 Lower voltage 0.0 … 10.0 V 1.0 V
Tset 2 Upper boiler temperature 10 … 90 °C 80 °C
Volt 2 Upper voltage 0.0 … 10.0 V 8.0 V
Tmin Minimum boiler temperature 1 … 90 °C 10 °C
Tmax Maximum boiler temperature 1 … 90 °C 80 °C
Sen. Flow Flow sensor option Yes, No No
Sensor Flow sensor selection system dependent S4
Interval Monitoring period 10 … 600 s 30 s
Hysteresis Correction hysteresis 0.5 … 20.0 K 1.0 K
Correction Correction of the voltage signal 0.1 … 1.0 V 0.1 V
Min. runtime Minimum runtime option Yes, No No
Min. runtime Minimum runtime 0 … 120 min 10 min
Pump 1 … 2 Shared relay option for loading
pump Activated, Deactivated Deactivated
Adjustment
channel Description Adjustment range /
selection Factory setting
Relay Relay selection system dependent system dependent
Start-up Pump delay No,Time,Temperature No
Delay Delay to a demand 0 … 300 s 60 s
TStart-up Boiler start-up temperature 10 … 90 °C 60 °C
Overrun Pump overrun No,Time,Temperature No
Overrun time Overrun time 0 … 300 s 60 s
TOverrun Remaining boiler temperature 10 … 90 °C 50 °C
Sensor Boiler
1 … 2 Boiler sensor selection system dependent system dependent
Valve 1 … 2 Activation of a shared relay
Parallel relay Activated, Deactivated Deactivated
Relay Relay selection system dependent system dependent
back
In this menu, up to 2 heating demands can be activated and adjusted.
Activated demands will be available for selection in the output alloca-
tion channels of the backup heating in heating circuits and heating op-
tional functions.This way, several heating circuits and optional functions
can demand the same heat source.
Every demand can be carried out by means of a relay and/or a 0-10 V output.
If both the Relay and the 0-10 V option are activated, the demand will use both
outputs in parallel.
Relay option
If the Relay option is activated, the sub-menu Relay appears, in which a relay can
be allocated to the demand.
The options Boiler protection min and Boiler protection max can be acti-
vated for the demand via a relay, allowing temperature-dependent control of the
boiler demand. For this purpose, a boiler sensor (Sensor Boiler) is required.
The Boiler pr. min option is used for protecting an older type boiler against
cooling. If the temperature falls below the adjusted minimum temperature, the
allocated relay is energised until the minimum temperature is exceeded by 2 K.
The Boiler pr. max option is used for protecting an older type boiler against
overheating.If the adjusted maximum temperature is exceeded, the allocated relay
is switched off until the temperature falls by 2 K below the maximum temperature.

20
Installation Commissioning Settings Data communication Troubleshooting
en
Example:
The potential-free relay R5 can be allocated to the demand. R5 will then become
available for potential-free boiler demand in the heating circuits and e. g. the DHW
heating function.
Example:
The potential-free relay R5 can be allocated to the shared relay Demand 1. R5
will then become available for potential-free boiler demand in the heating circuits
and e. g. the DHW heating function.
S3
S2
S1
R1
R2/3
R4
S4
R5
0-10 V option
If the 0-10V option is activated, the sub-menu 0-10V will appear, in which a 0-10 V
output can be allocated to the demand.
With this option, the controller can demand modulating heat generators equipped
with a 0-10 V interface.
The characteristic curve of the 0-10 V signal as a function of the boiler set tem-
perature are dened by means of 2 set points according to the specications of
the boiler manufacturer. At a temperature of Tset 1, the voltage signal of the
heat generator is Volt 1. At a temperature of Tset 2, the voltage signal of the
heat generator is Volt 2.The controller automatically calculates the characteristic
curve resulting from these values.
Spannungssignal in V
10V
Volt 2
Volt 1
0V
Tmin
TSoll 1 TSoll 2
Tmax
Kesselsolltemperatur in °C
Set boiler temperature in °C
Voltage signal in V
By means of the adjustment channels Tmax and Tmin the maximum and mini-
mum limitations for the boiler set temperature can be dened.
When the Sensorow option is activated, the controller will monitor whether
the heat generator actually reaches the desired set temperature and will, if nec-
essary, adjust the voltage signal accordingly. In order to do so, the controller will
check the temperature at the boiler ow sensor when the Interval has elapsed.
If the temperature measured deviates from the boiler set temperature by more
than the Hysteresis value, the voltage signal will be adapted by the Correction
value.This process will be repeated until the temperature measured is identical to
the boiler set temperature.
When the Min. runtime option is activated, a Minimum runtime can be ad-
justed for the demand.
Note:
If the 0-10 V demand is used for DHW heating, the voltage signal will
always be identical to Tmax.
Pump
For loading pumps, the shared relays Pump 1 and Pump 2 are available. Con-
cerning a demand, the options Start-up and Overrun can be activated for the
shared relays. The demand can either be time- or temperature controlled. For
temperature-dependent control an allocated boiler sensor is required.