Ozito TSF-1211U User manual

ASSEMBLING THE FRAME
TABLE SAW
2000W 250mm
ASSEMBLY INSTRUCTIONS
PARTS
FASTENERS
1. Turn the table saw upside down
and place it on the oor (Ensure the
blade is wound fully down before
turning the saw upside down).
2. Remove the box of parts from behind the
motor; it can be easy accessed by tilting the
blade using the Blade Bevel Adjustment.
3. Attach the Base Frame Legs (A) to
the bottom of the table saw, you will
rst need to remove the bolt and
washers from the table saw.
4. Ensure that the rectangular plastic cleats
on the table saw sit within the rectangular
slots at the top of the Base Frame Legs.
These cleats assist in support as well as
alignment. Use the bolts and washers
removed in step 3 to fasten all four legs to
the sides of the machine.
Note: Only hand tighten at this stage, as some movement in the legs will
assist in aligning the cross struts.
5. When aligning the Cross Struts to the
Base Frame Legs, ensure that the
shorter edge is facing the table saw.
Note: The Short Cross Struts (C) need to
be used on the sides of the table saw. Long
Cross Struts (B) front & back
6. Loosely x the 4 Cross Struts to the
base frame legs, using the nuts, bolts
and washers supplied.
7. The Table Saw is supplied with 2
Stabilising Brackets. 2 bolts, 2 nuts
2 at washers and 2 spring washers
are required to attach each bracket
to the bottom of the rear Base
Frame Legs.
8. Mount the Rubber Feet on the legs.
TSF-1211U
12. Bolt - 32 pc
13. Nut - 32 pc.
14. Washer, Flat - 32 pc.
15. Washer, Spring - 32 pc.
16. Spanner 10/13 mm
17. Spanner 10/21 mm
1. Legs (A)- 4 pc
2. Cross struts, long (B)- 2 pc
3. Cross struts, short (C) - 2 pc
4. Side table extension - 2 pc
5. Rear table extension - 1 pc
6. Feet - 4 pc
7. Dust extractor hose - 1 pc
8. Blade guard - 1 pc
9. Stabilising brackets - 2 pc
10. Support strut, side table - 4 pc
11. Support strut, rear table - 2 pc
1
12 13
76 910
8
234 5
ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to
the online manual.
11
14 15 16
17
WARNING! BEFORE ASSEMBLING YOUR TABLE SAW
OR REPLACING BLADES, MAKE SURE THAT THE
MOTOR IS OFF AND THE TOOL DISCONNECTED FROM THE
POWER SUPPLY TO PREVENT ACCIDENTAL STARTING.

The table saw is supplied with
one Rear Table Extension and
two Side Table Extensions.
1. Using the nuts, bolts and
washers supplied, attach
a table extension to the
main saw table. Each table
extension will require 2 bolts,
2 at washers, 2 spring
washers and 2 nuts
2. There are 2 support struts for
each table extension. When
attaching the support struts
to the table extensions, use
the nuts, bolts, at washers
and spring washers. Each
support strut will require 1
bolt, 1 nut, 1 at washer and
1 spring washer
Note: There are 4 short and 2 long support struts. The 2 longer support
struts are intended for the Rear Table Extension.
3. When attaching the support struts to
the bottom of the table saw, you will rst
need to remove the bolt and washer that
connect the leg to the table saw. Ensure
that it is supported by one other bolt
before attaching a strut.
4. Each base frame leg and support strut
share the same xing hole
5 Finally, tighten all the nuts on the base frame and table extensions to
ensure steadiness. Use the supplied spanner where required, but be
careful not to over tighten as this may result in damage to the base
frame legs.
FITTING THE BLADE GUARDATTACHING TABLE EXTENSIONS
1. Mount the blade guard on the
riving knife so that the bolt ts
through the hole in the riving
knife. Attach with locknut and
washer.
2. Do not tighten the bolt too far –
the blade guard must be able to
move freely.
3. Fasten the dust extractor hose
to the extractor adapter and
to the extractor socket of the
blade guard. A suitable extractor
system has to be connected
to the outlet of the extractor
adapter.
TSF-1211U
IMPORTANT! THE BLADE GUARD MUST ALWAYS
BE LOWERED OVER THE WORK PIECE BEFORE YOU
BEGIN TO CUT.