Ozito PHT-410 User manual

Pole Hedge Trimmer
410mm 900W
Instruction Manual
2 Year Replacement Warranty
PHT-410
WARNING! Read all safety warnings and all instructions. Failure to follow the
warnings and instructions may result in electric shock, fire and /or serious injury.
Save all warnings and instructions for future reference.
To view the full range visit: www.ozito.com.au
0212
!!

Motor: 900W
Input: 230-240V ~ 50Hz
No load speed: 1000/min
Blade length: 410mm
Max. blade capacity: 18mm
Weight (tool only): 6.05kgs
1. Blade
2. Gearbox
3. Blade adjustment locking knob
4. Angle Head locking mechanism
5. Upper locking lever
6. Lower locking lever
7. Blade angle adjustment handle
8. Upper shaft
9. Shaft locking knob
10. Adjustable auxiliary straight handle
11. Adjustable auxiliary D-handle
12. Lower shaft
13. Safety slide
14. Shoulder strap attachment bracket
15. Rotating handle lock
16. Lock off switch
17. On/off button
18. Rear handle
19. Extension cord restraint
20. Blade cover
21. Shoulder strap
22. Auxiliary handle bracket
2
SPECIFICATIONS - MODEL NO. PHT-410
3
1
6
KNOW YOUR PRODUCT
19
20
5
11
15
7
2
4
9
14
18
16
17
13
12
10
8
21 22

3
TABLE OF CONTENTS
SPECIFICATIONS ………………………………………..
INTRODUCTION…………………………………………
ELECTRICAL SAFETY…………….………………………
GENERAL SAFETY WARNINGS…………………………
HEDGE TRIMMER SAFETY WARNINGS
………………
ASSEMBLY…………………………………………… ……
OPERATION………………………………………………
MAINTENANCE…………….……………………………
TROUBLE SHOOTING…………….…………………….
SPARE PARTS …………….……………………………...
DESCRIPTION OF SYMBOLS ………………………….
PACK CONTENTS ………………………………………
WARRANTY………………………………………………
Page 2
Page 4
Page 4
Page 5
Page 7
Page 8
Page 9
Page 12
Page 13
Page 13
Page 14
Page 15
Page 16

INTRODUCTION
4
Congratulations on purchasing an Ozito Pole Hedge
Trimmer. We aim to provide quality tools at an
affordable price.
We hope you will enjoy using this tool for many years.
The PHT-410 Pole Hedge Trimmer has been designed
for trimming light foliage and is intended for DIY use only.
WARNING! When using mains-powered equipment, basic safety
precautions, including the following, should always be followed to reduce
risk of fire, electric shock, personal injury and material damage.
Read and understand the manual prior to operating this tool.
Save these instructions and other documents supplied with this tool for future
reference.
The electric motor has been designed for 230V and 240V only. Always check that
the power supply corresponds to the voltage on the rating plate.
Note: The supply of 230V and 240V on Ozito tools are interchangeable for
Australia and New Zealand.
This tool is double insulated in accordance with AS/NZS 60745-2-15;
therefore no earth wire is required.
If the supply cord is damaged, it must be replaced by a qualified electrician or a
power tool repairer in order to avoid a hazard.
If operating a power tool in a damp location is unavoidable use a residual current
device (RCD) protected supply Use of an RCD reduces the risk of electric shock.
Note: Double insulation does not take the place of normal safety precautions
when operating this tool. The insulation system is for added protection against
injury resulting from a possible electrical insulation failure within the tool.
Using an extension lead
Always use an approved extension lead suitable for the power input of this tool.
Before use, inspect the extension lead for signs of damage, wear and ageing.
Replace the extension lead if damaged or defective. When using an extension
lead on a reel, always unwind the lead completely. Use of an extension lead not
suitable for the power input of the tool or which is damaged or defective may
result in a risk of fire and electric shock.
ELECTRICAL SAFETY
!!
!
!

5
GENERAL POWER TOOL SAFETY WARNINGS
!!
WARNING! Read all safety warnings and all instructions. Failure to
follow the warnings and instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future reference.
The term “power tool" in all of the warnings refers to your mains-operated
(corded) power tool or battery-operated (cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases or dust. Power tools create sparks which
may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool. Distractions
can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any way.
Do not use any adapter plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces, such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric shock if
your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power
tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging
the power tool. Keep cord away from heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for
outdoor use. Use of a cord suitable for outdoor use reduces the risk of
electric shock.
f) If operating a power tool in a damp location is unavoidable, use a residual
current device (RCD) protected supply. Use of an RCD reduces the risk of
electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use common sense when operating
a power tool. Do not use a power tool while you are tired or under the
influence of drugs, alcohol or medication. A moment of inattention while
operating power tools may result in serious personal injury.
b) Use personal protective equipment. Always wear eye protection. Protective
equipment such as dust mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off-position before
connecting to power source and/or battery pack, picking up or carrying the
tool. Carrying power tools with your finger on the switch or energising power tools
that have the switch on invites accidents.
!
!

6
GENERAL POWER TOOL SAFETY WARNINGS
!!
d) Remove any adjusting key or wrench before turning the power tool on. A
wrench or a key left attached to a rotating part of the power tool may result in
personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This
enables better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair,
clothing and gloves away from moving parts. Loose clothes, jewellery or
long hair can be caught in moving parts.
g) If devices are provided for the connection of dust extraction and
collection facilities, ensure these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer at the rate
for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off. Any
power tool that cannot be controlled with the switch is dangerous and must
be repaired.
c) Disconnect the plug from the power source and/or the battery pack from
the power tool before making any adjustments, changing accessories, or
storing power tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow
persons unfamiliar with the power tool or these instructions to operate
the power tool. Power tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power
tool's operation. If damaged, have the power tool repaired before use.
Many accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with
sharp cutting edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc. in accordance with
these instructions, taking into account the working conditions and the
work to be performed. Use of the power tool for operations different from
those intended could result in a hazardous situation.
5) Service
a) Have your power tool serviced by a qualified repair person using only
identical replacement parts. This will ensure that the safety of the power tool
is maintained.
b) If the supply cord is damaged, it must be replaced by the manufacturer,
its service agent or similarly qualified persons in order to avoid a hazard.

7
HEDGE TRIMMER SAFETY WARNINGS
!!
•Keep all parts of the body away from the cutter blade. Do not remove cut
material or hold material to be cut when blades are moving. Make sure the switch
is off when clearing jammed material. A moment of inattention while operating the
hedge trimmer may result in serious personal injury.
•Carry the hedge trimmer by the handle with the cutter blade stopped. When
transporting or storing the hedge trimmer always fit the blade cover. Proper handling
of the hedge trimmer will reduce possible personal injury from the cutter blades.
•Hold the power tool by insulated gripping surfaces only, because the cutter
blade may contact hidden wiring or its own cord. Cutter blades contacting a
"live" wire may make exposed metal parts of the power tool "live" and could give
the operator an electric shock.
•Keep cable away from cutting area. The cable may be hidden in shrubs and can
be accidentally cut by the blade during operation.
•Perform visual inspection on the hedge being trimmed. Ensure that there are
no wire fences or foreign objects that may come into contact with the Pole Hedge
Trimmer during operation.
•If the cord becomes damaged during use, disconnect the cord from the
supply immediately. DO NOT TOUCH THE CORD BEFORE DISCONNECTING
THE SUPPLY. Do not use the Pole Hedge trimmer if the cord is damaged or worn.
•Inspect and maintain the Pole Hedge Trimmer regularly. Have the Pole Hedge
Trimmer repaired by an authorized repairer.
• Keep extension cord away from cutting blades.
•Never allow children or people unfamiliar with these instructions to use the Pole
Hedge Trimmer.
• Avoid using the Pole Hedge Trimmer, while people, especially children or pets are nearby.
• Use the Pole Hedge Trimmer only in daylight.
•Never operate the Pole Hedge Trimmer with a damaged cutting blade.
•Switch on the Pole Hedge Trimmer only when hands and feet are away from the
cutting blades.
•Use only manufacturer's recommended replacement parts and accessories.
• Always disconnect the Pole Hedge Trimmer from the mains power outlet and put
the blade cover on when leaving the Pole Hedge Trimmer unattended.
•Disconnect the Pole Hedge Trimmer from the mains power outlet before carrying
out any maintenance or cleaning work.
• When not in use, store the Pole Hedge Trimmer out of the reach of children
•Face the cutting blades away from yourself, other people and and animals while
the power is connected to the Pole Hedge Trimmer (especially during operation).
•Use both handles and shoulder strap.
• Keep ventilation openings clear of debris. Keep handles dry, clean and free of oil
and grease.
•Never reach underneath the Pole Hedge Trimmer cutting blades until it has
completely stopped and the power has been disconnected.
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning use of
the appliance by a person responsible for their safety.
Recommendations for the use of a residual current device with a rated residual
current of 30mA or less.

8
HEDGE TRIMMER SAFETY WARNINGS (cont.)
Using an Extension Lead
Always use an approved extension lead suitable for the power input of this tool.
Before use, inspect the extension lead for signs of damage, wear and ageing.
Replace the extension lead if damaged or defective.
When using an extension lead on a reel, always unwind the lead completely. Use
of an extension lead not suitable for the power input of the tool or which is
damaged or defective may result in a risk of fire and electric shock.
It is recommended that the extension lead is a maximum of 25m in length. Do Not
use multiple extension leads.
WARNING! Before assembly, make sure that the hedge trimmer is
switched off and unplugged from the mains outlet.
Assembling upper shaft to lower shaft
1. Align the upper shaft locking button (a) with the
locking hole of the lower shaft (12) (Fig. 1).
2. Slide the upper shaft (8) of the pole hedge
trimmer on to the lower shaft (12).
3. Ensure the upper shaft locking button (a) clicks
into the hole of the lower shaft (12).
Note: Gently pull the upper shaft (8) to ensure the locking button has engaged
correctly into the hole of the lower shaft (12).
4. Once the upper shaft (8) and lower shaft (12)
have locked together tighten the shaft locking
knob (9) in a clockwise direction (Fig. 2).
Assembling the adjustable auxiliary handle
1. Locate the adjustable auxiliary D-handle (11) and adjustable auxiliary straight
handle (10) onto the lower shaft (12) between the two safety slides (13).
2. Place the adjustable auxiliary handle bracket (22)
onto the lower shaft (12) and insert the 2 x allen
screws supplied through the holes of the auxiliary
handle bracket (22), adjustable auxiliary D-handle
(11) and adjustable auxiliary straight handle (10).
3. Position the auxiliary handles to a comfortable
position and tighten the two screws with the allen
key (b) provided (Fig. 3).
Note: The allen key is located on the underside of the
auxiliary straight handle.
!
!
Fig. 1
Fig. 2
Fig. 3
a
ASSEMBLY
!!
Allen
key
holder
b

9
Adjusting the auxiliary handle
1. Loosen the two allen screws securing auxiliary handle bracket (21), adjustable
auxiliary D-handle (11) and adjustable auxiliary straight handle (10).
2. Move adjustable auxiliary handles up or down to the desired position. Retighten
the two bolts to secure the adjustable handles.
Assembling the shoulder strap
1. Hook the shoulder strap (21) onto the shoulder strap
attachment bracket (14) (Fig. 4).
2. Adjust the shoulder strap (21) to a length that is
suitable to you.
Adjusting the blade angle
WARNING! DO NOT hold the blade in an attempt to adjust the blade angle.
Doing so may result in possible personal injury.
1. Lie the pole hedge trimmer on the ground, then hold
the upper shaft (8) firmly and turn the blade
adjustment locking knob (3) anti clockwise to unlock
the head locking mechanism (4).
2. Hold the blade angle adjustment handle (7) with the
other hand and depress both the lower locking lever (6)
and the upper locking lever (5) simultaneously (Fig. 7).
3. Rotate the blade to the desired angle. Release both locking levers. Continue to rotate
until both levers 'click' to locate in one of the preset positions.
4. Tighten the blade adjustment locking knob (3) by rotating clockwise.
WARNING! If cordset is cut or damaged remove it immediately from the power
point. This product requires the use of two hands to ensure safe operation. Inspect
the area to be cut before starting. Remove any objects or debris that could be
thrown, jammed or become entangled in the blades.
Cord retainer
1. Make a loop with the extension cord and push it
through the square hole at the back of the rear
handle (18) (Fig. 5).
2. Place the end of the loop around the extension cord
restraint (19) and ensure it is pulled firmly enough to
prevent it coming loose while operating the pole
hedge trimmer.
3. Connect the extension cord socket to the pole hedge trimmer cord socket.
!
!
Fig. 4
Fig. 5
!
!
ASSEMBLY (cont.)
Fig. 7
OPERATION

10
Switching on/off
WARNING! Familiarise yourself with surrounding hazards such as power
lines, phone lines, metal fences and other objects that could be in your
trimming path, failure to do so could result in electrical shock, personal
injury or damage to your pole hedge trimmer.
For your safety, the Pole Hedge Trimmer is designed
with a two button safety switch. If only one switch is
squeezed, the tool will not operate.
1. Hold the Pole Hedge Trimmer with both hands,
and away from your body.
2. Depress the lock-off switch (16) and squeeze the
on/off button (17) (Fig. 6).
3. To turn the Pole Hedge Trimmer off, simply release the on/off button (17).
Blade brake
The Pole Hedge Trimmer is fitted with a motor brake which will stop the cutting
blade within 1 second of releasing the on/off button (17).
Note: There may be some sparking (or flashing) in the area of the motor
ventilation slots when the pole hedge trimmer is switched off and the blade
brake engages. This is normal and will not damage the machine.
Trimming instructions
WARNING! Familiarise yourself with surrounding hazards such as power
lines, phone lines, metal fences and other objects that could be in your
trimming path, failure to do so could result in electrical shock, personal
injury or damage to your pole hedge trimmer.
WARNING! Never use the pole hedge trimmer when standing on a
ladder or uneven ground.
1. Extension cord. Always keep the extension cord behind the pole hedge
trimmer and away from the trimming operation. Never drape it over a hedge
being trimmed. If you cut or damage the cord, unplug it at the mains electrical
outlet immediately. It must be repaired by an electrician or a power tool
repairer before being used again.
2. Working position. Maintain proper footing and balance and do not
overreach. Wear safety goggles, non-slip footwear and rubber gloves when
trimming. Hold the pole hedge trimmer firmly in both hands before turning
the pole hedge trimmer on. Always hold the pole hedge trimmer with one
hand on the rear handle and one hand on the adjustable auxiliary handle.
OPERATION (cont.)
!
!
!
!
!
!
Fig. 6

3. Trimming new growth. Using a wide sweeping
motion, feed the blade teeth through the twigs. A
slight downward tilt of the blade, in the direction of
motion gives the best cut (Fig. 8).
Note: Do not use the pole hedge trimmer for cutting stems greater than 18mm.
Use the trimmer only for cutting normal shrubbery found around houses and
buildings.
4. Level hedges. To obtain exceptionally level hedges a piece of string can be
stretched along the length of the hedge as a guide.
5. Side-trimming hedges. Hold the pole hedge
trimmer and begin at the bottom and sweep up
(Fig. 9).
6. Cutting sequence. First cut both sides, starting at the bottom and work to the
top: this prevents cuttings from falling into the area where you are still working.
7. Trimming the top. Where the branches have grown extremely long, cut back the
hedge in several stages.
8. General information. When older hedges are to be cut back a substantial
amount, use pruning shears or some other device to trim thicker branches (greater
than 18mm diameter) to the desired length before starting work with the pole
hedge trimmer.
Ensure the blades do not come into contact with any object made of hard material
that could damage the blades, such as wire fencing or metal plant supports.
Caution: If the blades come in contact with a hard object, visually inspect the blade
for damage. If the blade is damaged, do not continue to operate the Pole Hedge Trimmer.
11
OPERATION (cont.)
Fig. 8
Fig. 9

12
MAINTENANCE
WARNING! Always ensure that the trimmer is switched off and the plug is
removed from the power point before making any adjustments
• When not in use, the Pole Hedge Trimmer should be stored in a dry, frost free
location not within the reach of children.
• Keep ventilation slots of the Pole Hedge Trimmer clean at all times and
prevent any foreign matter from entering.
• If the enclosure of the Pole Hedge Trimmer requires cleaning do not use
solvents but a moist cloth only.
• There are no user serviceable parts in the Pole Hedge Trimmer; if a fault is
suspected, please contact Ozito customer service.
• If the supply cord requires replacement, please take your Pole Hedge Trimmer
to an authorized power tool repairer/ electrician to repair the damaged cord.
• The blade rail should be cleaned and treated with light machine oil or spray
lubricant (such as WD40, CRC 5.56 or RP7) after each use. When a job lasts for
a longer period of time it is recommended that the blade rail also be treated
with spray lubricant at regular intervals during operation.
Carbon brushes
When the carbon brushes wear out the tool will spark
and/or stop. Discontinue use as soon as this happens. They
should be replaced prior to recommencing use of the tool.
Carbon brushes are a wearing component of the tool and
therefore not covered under warranty. Continuing to use
the tool when carbon brushes need to be replaced may
cause permanent damage to the tool. Carbon brushes will
wear out after many uses but when the carbon brushes need to be replaced take
the tool to an electrician or a power tool repairer for a quick and low cost
replacement. Always replace both carbon brushes at the same time.
Note: Ozito Industries will not be responsible for any damage or injuries caused
by the repair of the tool by an unauthorised person or by mishandling of the tool.
!
!
carbon brushes

13
TROUBLE SHOOTING
Problem Possible Cause Solution
Does not start No supply voltage Check the mains power,
power cord, extension
cord, plug and house fuse.
Contact Ozito customer
service
Switch ON / OFF are broken
Carbon brushes are worn
Motor defective
Pole Hedge
Trimmer works
intermittently
Damaged electricity
power cord
Check power cable. If
damaged, contact Ozito
customer service.
On/off switch may be damaged Contact Ozito customer
Service
Upper and lower shafts are
not securely fasten
Blade turning hot Dull and/or damaged blades Contact Ozito customer
service
Blades are binging due to
lack of lubrication
Check the blades and
lubricate or contact ozito
service center for
replacement blades
Lubricate the blade with light
machine oil or spray lubricant.
Limited spare parts are available subject to availability. Please contact your local
Bunnings Special Orders Desk to order the required spare parts.
Most common spare parts listed below
Spare Part Part No.
Shaft Locking Knob SPPHT410-011
Carbon Brush (set) SPPHT410-045
Lock-off Switch SPPHT410-051
Shoulder Strap SPPHT410-123
SPARE PARTS

DESCRIPTION OF SYMBOLS
14
Warning
Read instruction manual
Wear gloves for
cutting protection
Wear safety shoes for
preventing slipping
Wear personal protective equipment.
Always wear safety glasses or a face
shield, hearing protection and
safety helmet
Caution:Keep it at least
10m away from
Transmission lines.
VVolts Hz Hertz
~Alternating current WWatts
n o No load speed
Double insulated
/min Revolutions or reciprocation per minute
Regulator compliance mark
Keep hands away from blade
Beware of falling objects
Do not expose the electric hedge
trimmer to the rain
Keep bystanders away from the electric
hedge trimmer
The sound power level
indicates by L
WA in dB
Cutting length Electrical appliances can not be thrown
into the family dustbin
Gearbox will become hot to touch after use
Remove plug from the mains immediately
if the cable is damaged or cut
102

AUSTRALIA (Head Office)
1 - 23 Letcon Drive, Bangholme, Victoria, Australia 3175
Telephone: [phone]
Facsimile: [phone]
Website: www.ozito.com.au
Email: [email protected]
1 x Pole Hedge Trimmer (PHT-410)
1 x Blade cover
2 x Allen screws
1 x Adjustable auxiliary D-handle
1 x Adjustable auxiliary straight handle
1 x Adjustable auxiliary handle bracket
1 x Allen key
1 x Instruction manual
Power tools that are no longer usable should not be
disposed of with household waste but in an environmentally
friendly way. Please recycle where facilities exist. Check with
your local council authority for recycling advice.
Recycling packaging reduces the need for landfill and raw
materials. Reuse of recycled material decreases pollution in the
environment. Please recycle packaging where facilities exist.
Check with your local council authority for recycling advice.
15
SPARE PARTS
PACK CONTENTS
OZITO INDUSTRIES PTY LTD

2 YEAR REPLACEMENT WARRANTY
Your product is guaranteed for a period of 24 months from the original date of purchase
and is intended for DIY (Do It Yourself) use only. If a product is defective it will be replaced in
accordance with the terms of this warranty. Warranty excludes consumable parts, for example:
blade cover, allen screws, allen key, adjustable auxiliary handle, handle bracket.
WARNING
The following actions will result in the warranty being void.
Professional, Industrial or high frequency use.
If the tool has been operated on a supply voltage other than that specified on the tool.
If the tool shows signs of damage or defects caused by or resulting from abuse, accidents
or alterations.
Failure to perform maintenance as set out within the instruction manual.
If the tool is disassembled or tampered with in any way.
OZITO
Australia/New Zealand (Head Office)
1-23 Letcon Drive, Bangholme, Victoria, Australia 3175
•
•
•
•
•
OW8
WARRANTY
YOUR WARRANTY FORM SHOULD BE RETAINED BY YOU AT ALL TIMES. IN ORDER
TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST RETURN THE PRODUCT TO
YOUR NEAREST BUNNINGS WAREHOUSE WITH YOUR BUNNINGS REGISTER RECEIPT.
PRIOR TO RETURNING YOUR PRODUCT FOR WARRANTY PLEASE TELEPHONE OUR
CUSTOMER SERVICE HELPLINE:
TO ENSURE A SPEEDY RESPONSE PLEASE HAVE THE MODEL NUMBER AND DATE OF
PURCHASE AVAILABLE. A CUSTOMER SERVICE REPRESENTATIVE WILL TAKE YOUR CALL
AND ANSWER ANY QUESTIONS YOU MAY HAVE RELATING TO THE WARRANTY POLICY
OR PROCEDURE.
The benefits provided under this warranty are in addition to other rights and remedies which
are available to you at law.
Our goods come with guarantees that cannot be excluded at law. You are entitled to a
replacement or refund for a major failure and for compensation for any other reasonably
foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if
the goods fail to be of acceptable quality and the failure does not amount to a major failure.
Generally you will be responsible for all costs associated with a claim under this warranty,
however, where you have suffered any additional direct loss as a result of a defective product
you may be able to claim such expenses by contacting our customer service helpline above.
` Australia 1800 069 486
New Zealand 0508 069 486