Ozito HT-501 User manual

Hedge
Trimmer
450 Watt
Operation Manual
2 Year Replacement Warranty
HT-501
To view the full range visit: www.ozito.com.au
0109

SPECIFICATIONS - MODEL NO. HT-501
3
Motor size: 450W
Input: 230V ~ 50Hz
No load speed: 2100 /min
Blade length: 360 mm
Blade spacing: 11 mm
Features: Dual action safety switch
Cord retainer
Safety guard
Blade brake
Dual action blades
Hard blade sheath
1. Body handle
2. On/off switch
3. Front handle
4. Safety guard
5. Blade support rail
6. Dual action blade
7. Safety switch
8. Cord retainer
1
2
3
4
8
5
6
7

INTRODUCTION
4
SAFETY INSTRUCTIONS
ELECTRICAL SAFETY
Warning! When using mains-powered equipment, basic safety precautions,
including the following, should always be followed to reduce risk of fire,
electric shock, personal injury and material damage.
Read and understand the manual prior to operating this tool.
Save these instructions and other documents supplied with this tool for future reference.
The electric motor has been designed for 230V and 240V only. Always check that
the power supply corresponds to the voltage on the rating plate.
Note: The supply of 230V and 240V on Ozito tools are interchangeable for
Australia and New Zealand.
This tool is double insulated in accordance with AS/NZS 3100: 2002;
therefore no earth wire is required.
If the supply cord is damaged, it must be replaced by an electrician or a power
tool repairer in order to avoid a hazard.
Note: Double insulation does not take the place of normal safety precautions when
operating this tool. The insulation system is for added protection against injury
resulting from a possible electrical insulation failure within the tool.
Using an Extension Lead
Always use an approved extension lead suitable for the power input of this tool.
Before use, inspect the extension lead for signs of damage, wear and ageing.
Replace the extension lead if damaged or defective. When using an extension lead
on a reel, always unwind the lead completely. Use of an extension lead not suitable
for the power input of the tool or which is damaged or defective may result in a risk
of fire and electric shock.
Congratulations on purchasing an Ozito Hedge Trimmer.
We aim to provide quality tools at an affordable price.
We hope you will enjoy using this tool for many years.
Your Hedge Trimmer HT-501 has been designed for
trimming light foliage and is intended for DIY use only.

5
GENERAL
1. Keep work areas clean. Cluttered work areas and benches can cause accidents.
2. Consider work area environment. Do not expose your tool to high humidity or
rain. Do not use your tool in damp or wet conditions. Keep the work area well lit.
Do not use your tool where there is a risk of causing fire or explosion, e.g. in the
presence of flammable liquids and gases.
3. Keep children away. Do not allow children, visitors or animals to come near the
work area or to touch the tool or power lead.
4. Dress appropriately. Do not wear loose clothing or jewellery, as these can
be caught in moving parts. Preferably wear non-slip footwear when working
outdoors. Wear protective hair covering to keep long hair out of the way.
5. Head protection. Always use safety glasses. Use a face or dust mask whenever the
operations may produce dust or flying particles. Wear ear protection whenever the
sound level seems uncomfortable.
6. Guard against electric shock. Prevent body contact with earthed or grounded
surfaces (e.g. pipes, radiators, cookers and refrigerators). Electric safety can be further
improved by using a high sensitivity (30 mA / 30 mS) residual current device (RCD).
7. Do not overreach. Keep proper footing and balance at all times.
8. Stay alert. Watch what you are doing. Use common sense. Do not operate
the tool when you are tired.
9. Secure work piece. Use clamps or a vice to hold the work piece; it is safer
as it frees both hands to operate the tool.
10. Remove adjusting keys and wrenches. Always check that adjusting keys
and wrenches are removed from the tool before operating the tool.
11. Extension leads. Before use inspect the extension leads and replace if damaged.
When using the tool outdoors, only use extension leads intended for outdoor use
and marked accordingly.
12. Use appropriate tool. The intended use is described in this instruction manual. Do
not force small tools or attachments to do the job of a heavy duty tool. The tool
will do the job better and safer at the rate for which it was intended. Do not force
the tool.
Warning! The use of any accessory or attachment, or performance of any
operation with this tool other than those recommended in this instruction manual
may present a risk of personal injury.

GENERAL (cont.)
6
13. Check for damaged parts. Before use carefully check the tool and power lead
for damage. Check for misalignment and seizure of moving parts, breakage of
parts, damage to guards and switches and any other conditions that may affect
its operation. Ensure that the tool will operate properly and perform its
intended function. Do not use the tool if any parts are damaged or defective.
Do not use the tool if the switch does not turn it on and off. Have any
damaged or defective parts repaired or replaced by an electrician or a power
tool repairer. Never attempt any repairs yourself.
14. Unplug the tool. Shut off the power and wait for the tool to come to a
complete standstill before leaving it unattended. Unplug the tool when it is not
in use, before changing any parts of the tool, accessories or attachments and
before servicing.
15. Avoid unintentional starting. Do not carry the tool with a finger on the on/off
switch. Make sure the tool is switched off when plugging in.
16. Do not abuse the cord. Never carry the tool by its cord or pull it to disconnect
from the socket. Keep the cord away from heat, oil and sharp edges.
17. Connect dust extraction equipment. If devices are provided for the
connection of dust extraction and collection facilities, ensure that these are
connected and properly used.
18. Store idle tools. When not in use, tools should be stored in a dry, locked up or
high place, out of reach of children.
19. Maintain tools with care. Keep tools clean and in good condition for better
and safer performance. Follow the instructions for maintenance and changing
accessories. Keep handles and switches dry, clean and free from oil and grease.
20. Have your tool repaired by an electrician or a power tool repairer. This
power tool complies with relevant safety requirements. To avoid danger,
electrical appliances must only be repaired by qualified technicians using
original spare parts; otherwise this may result in considerable danger to the user.
21. Users. This appliance is not intended for use by young children or infirmed
persons without supervision. Young children should be supervised to ensure
that they do not play with this appliance.
22. Replacement of the supply cord. If the supply cord is damaged, it must be
replaced by an electrician or a power tool repairer in order to avoid a hazard.

ASSEMBLY
7
OPERATION
Cord retainer
When attaching an extension cord to the Trimmer, hook the end of the extension cord
into the cord retainer built into the rear of the Trimmer’s housing. Using the retainer
prevents accidental disconnection of the trimmer and extension cords plug and socket.
Always be sure to route the cord away from the work area to prevent it from coming
near the blade. Decide how you want to route the cord before starting work.
Start trimming at the point nearest the electrical outlet, then move away while working.
The cable will then be pulled through the area which has already been cut and thus
reduce the danger of itself being cut.
Switching On
For your safety this Hedge Trimmer is designed with a two hand safety switch. If you
only squeeze one switch the Hedge Trimmer will not be activated. To turn the Hedge
Trimmer ON squeeze both switches at the same time.
Switching Off
To turn the Hedge Trimmer OFF, simply release either switch.
Blade Brake
The Hedge Trimmer is fitted with a motor brake which will almost instantaneously stop
the cutting blade.
When the unit is switched off and the motor brake operates there may be some
sparking (or flashing) occurring in the area of the upper motor ventilation slots.
This is normal and will not damage the machine.
Trimming Instructions
1. Extension cord. Always keep the extension cord behind the Trimmer and away from
the trimming operation. Never drape it over a hedge being trimmed. If you cut or
damage the cord, unplug it at the electrical outlet immediately. It must be repaired
by an electrician or a power tool repairer before being used again.
2. Working position. Maintain proper footing and balance and do not overreach.
Wear safety goggles, non-slip footwear and rubber gloves when trimming. Hold
the tool firmly in both hands and turn the tool ON. Always hold the trimmer with
one hand on the body handle and one hand on the front handle. Never hold the
tool by the blade guard.

OPERATION (cont.)
8
3. Trimming new growth. A wide sweeping motion, feeding the blade teeth
through the twigs is most effective. A slight downward tilt of the blade,
in the direction of motion gives the best cut.
Do not use the Trimmer for cutting stems greater than 10 mm. Use the
Trimmer only for cutting normal shrubbery found around houses and buildings.
4. Level hedges. To obtain exceptionally level hedges a piece of string can
be stretched along the length of the hedge as a guide.
5. Side-trimming hedges. Hold the Trimmer and begin at the bottom and sweep up.
6. Shaping. The hedge should be trimmed to achieve a trapezoidal form, that is, it
should widen toward the bottom at both sides. This improves the penetration of
light to the lower extremities. A general guideline is approximately 10 cm slant
for each 1 metre of hedge height.
7. Cutting sequence. First cut both sides, starting at the bottom and work to the top:
this prevents cuttings from falling into the area where you are still working.
8. Trimming the top. Where the branches have grown extremely long, cut back
the hedge in several stages. The shorter the cuttings the better suited
for composting.
9. General information. When older hedges are to be cut back a substantial
amount, use pruning shears or some other device to trim thicker branches
(that is greater than 10 mm diameter) to the desired length before starting
work with the Hedge Trimmer.
To shape precisely, run a taught line between the extreme edges of the hedge
and then trim along the length of the line.
Ensure the blades do not come into contact with any object made of hard material
that could damage the blades, such as fencing wire or metallic plant supports.

9
Turn off Tool and Disconnect from Power Supply.
• When not in use, the Hedge Trimmer should be stored in a dry, frost free location
not within the reach of children.
• Keep ventilation slots of the Trimmer clean at all times and prevent any
foreign matter from entering.
• If the enclosure of the Trimmer requires cleaning do not use solvents
but a moist cloth only.
• There are no user serviceable parts in the Trimmer; if a fault is suspected or the
supply cord requires replacement, return the Trimmer to a power tool repairer.
• The blade rail should be cleaned and treated with light machine oil or spray
lubricant (such as WD40, CRC 5.56 or RP7) after each use. When a job lasts for a
longer period of time it is recommended that the blade rail also be treated with
spray lubricant at regular intervals during operation.
• When the carbon brushes wear out the tool will spark and/or stop. The brushes are
a wearing component of the tool and should be replaced prior to the carbon
wearing out fully. Brushes will wear out after many uses but before they do take
the tool to an electrician or a power tool repairer for quick and low cost
replacement. Always replace both brushes at the same time.
Note: Ozito Industries will not be responsible for any damage or injuries caused by
repair of the Trimmer by an unauthorised person or mishandling or mistreatment of the
tool. This tool is designed for DIY use – use in commercial or industrial environments
will void the warranty. The blades are not covered by warranty – any damage to or
sharpening of the blades are the responsibility of the user. Use of the Hedge Trimmer
with blunt blades will place excessive load on the motor and gearbox. Ozito Industries
cannot accept warranty liability for damage caused by lack of maintenance to the
Hedge Trimmer.
MAINTENANCE

AUSTRALIA (Head Office)
1-23 Letcon Drive, Bangholme, Victoria, Australia 3175
Telephone:[phone]
Website: www.ozito.com.au
Email: [email protected]
1 x Hedge Trimmer HT-501
1 x Blade sheath
1 x Instruction manual
CONTENTS
10
OZITO INDUSTRIES PTY LTD

WARRANTY
THIS WARRANTY FORM AND CONFIRMED BUNNINGS REGISTER RECEIPT SHOULD
BE RETAINED BY THE CUSTOMER AT ALL TIMES
The warranty is only made available by returning the product to your nearest
Bunnings Warehouse with a confirmed Bunnings register receipt.
PURCHASED FROM: ________________________________________________
DATE PURCHASED: _________________________________________________
2 YEAR REPLACEMENT WARRANTY
Your Ozito tool is guaranteed for a period of 24 months from the original date of
purchase and is intended for DIY (Do it yourself) use only.
WARNING
The following actions will result in the warranty being void.
•Professional, Industrial or high frequency use.
•If the tool has been operated on a supply voltage other than that specified on
the tool.
•If the tool shows signs of damage or defects caused by or resulting from abuse,
accidents or alterations.
•If the tool is disassembled or tampered with in any way.
Note: Warranty excludes consumable parts such as carbon brushes, chains, blades,
lubricants, guide bars, drive sprockets and other accessories.
YOUR WARRANTY FORM SHOULD BE RETAINED
BY YOU AT ALL TIMES.
SHOULD YOU HAVE ANY QUESTIONS PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY OR
REPAIR PLEASE TELEPHONE OUR CUSTOMER
SERVICE HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
TO ENSURE A SPEEDY RESPONSE PLEASE HAVE THE MODEL NUMBER
AND DATE OF PURCHASE AVAILABLE. AN OZITO CUSTOMER SERVICE
REPRESENTATIVE WILL TAKE YOUR CALL AND ANSWER ANY QUESTIONS
YOU MAY HAVE RELATING TO THE WARRANTY POLICY OR PROCEDURE.