Ozotech EOG 200 Manual
Enhanced Oxygen Generator
EOG 200
Operation & Maintenance Manual
OZOTECH, Inc. • 1015 South Main Street, Yreka, CA 96097 • Ph. 530.842.4189 • ozotech.com
OZOTECH, Inc. • 1015 South Main Street, Yreka, CA 96097 • Ph. 530.842.4189 • ozotech.com
Table of Contents
1.0 Caution 3
2.0 Installation and Operation 4
2.1 Operating Environment 4
3.0 Maintenance 9
5.0 Specifications 13
7.0 Troubleshooting Guide 15
Mainenance Notes
OZOTECH, Inc. • 1015 South Main Street, Yreka, CA 96097 • Ph. 530.842.4189 • ozotech.com 2.
Dear Valued Customer:
set up.
products.
OZOTECH, Inc. • 1015 South Main Street, Yreka, CA 96097 • Ph. 530.842.4189 • ozotech.com
1.0 Caution
3.
equipment.
never be allowed to come in contact with water.
maintain and operate this equipment.
a fuse or circuit breaker.
this equipment.
*
OZOTECH, Inc. • 1015 South Main Street, Yreka, CA 96097 • Ph. 530.842.4189 • ozotech.com
2.0 Installation and Operation
Your generator requires special operating conditions in
generator is designed to be operated under a negative
pressure situation.
in this manual.
2.1 Operating Environment
operating environment. Consideration of these factors
best possible operating environment that is available at
consistent operation of all ozone generators. Make a
4.
OZOTECH, Inc. • 1015 South Main Street, Yreka, CA 96097 • Ph. 530.842.4189 • ozotech.com
bracket from backplate.
in place.
Make sure the wire is flush in the channel for
proper bracket installation.
until it “snaps” into place.
1. Mount the EOG to the Clack® control valve. A
receiver.
5.
2.2 Installation
OZOTECH, Inc. • 1015 South Main Street, Yreka, CA 96097 • Ph. 530.842.4189 • ozotech.com
the back of the EOG.
2.2 Installation Continued
6.
b. Set backwash to 14 minutes
c. Set draw time* See below
longer than backwash)
less than draw time)
relative to tank size should be used.
OZOTECH, Inc. • 1015 South Main Street, Yreka, CA 96097 • Ph. 530.842.4189 • ozotech.com
board within the EOG has several inputs and outputs. The
LED Diagnostic Functions:
Green Light Blinking Slowly:
Green Light Blinking Quickly:
Green Light Solid:
Red Light Solid:
Red Light Flashing:
Orange Light:
7.
2.3 Operation
OZOTECH, Inc. • 1015 South Main Street, Yreka, CA 96097 • Ph. 530.842.4189 • ozotech.com
Control Input:
after the pilot signal is shut off. These outputs are capable
Fusing:
power on/off to reset.
solid red until condition is remedied. If either NO or NC
2.3 Operation Cont.
8.
OZOTECH, Inc. • 1015 South Main Street, Yreka, CA 96097 • Ph. 530.842.4189 • ozotech.com
T
3.1 Ozone Generator Maintenance
Note:
3.0 Maintenance
9.
OZOTECH, Inc. • 1015 South Main Street, Yreka, CA 96097 • Ph. 530.842.4189 • ozotech.com
*
1.
the ozone generator:
b. Cut the CD cell retaining strap holding the cell
c. Disconnect the air inlet and ozone outlet hoses
from the CD cell barb fittings.
clips.
2.
the CD cell barb fittings.
3.
from the opposite barbed fitting.
4.
secure.
3.1 Ozone Generator Maintenance Continued
10.
OZOTECH, Inc. • 1015 South Main Street, Yreka, CA 96097 • Ph. 530.842.4189 • ozotech.com
cleaning procedure:
1. Disconnect the EOG from power source.
3. Inspect the inside of the generator for dust and moisture.
button.
11.
3.1 Ozone Generator Maintenance Continued
OZOTECH, Inc. • 1015 South Main Street, Yreka, CA 96097 • Ph. 530.842.4189 • ozotech.com
12.
board:
1. Disconnect power from the EOG.
pulse green when finished.
Note:
OZOTECH, Inc. • 1015 South Main Street, Yreka, CA 96097 • Ph. 530.842.4189 • ozotech.com
13.
5.0 Specifications
nominal
Ozone Output: 220 mg/hr.
OZOTECH, Inc. • 1015 South Main Street, Yreka, CA 96097 • Ph. 530.842.4189 • ozotech.com
6.0 Component Replacement
CD Cell Replacement
1.
the ozone generator:
b. Cut the CD cell retaining strap holding the cell
c. Disconnect the air inlet and ozone outlet hoses
from the CD cell barb fittings.
2.
14.
OZOTECH, Inc. • 1015 South Main Street, Yreka, CA 96097 • Ph. 530.842.4189 • ozotech.com
7.0 Troubleshooting Guide
15.
System Possible Cause Solution
Unit
Unit is not connected
connected to improper
power source
requirements on pg.
connections.
and check for loose
connections. Inspect
Inspect HV wire from
Unit is connected to
improper power source
that unit is plugged into
proper voltage outlet.
no ozone
output
defective
high voltage lead not
connected to ozone cell
Connect red flag
connection.
to back up into the CD
cell and has caused a
Cell is plugged with
the lack of proper air
preparation
OZOTECH, Inc. • 1015 South Main Street, Yreka, CA 96097 • Ph. 530.842.4189 • ozotech.com16.
malfunction or defect to be a result of:
recommended in this manual.
2. Failure to adhere to and provide proper operating
specifications.
OZOTECH, Inc. • 1015 South Main Street, Yreka, CA 96097 • Ph. 530.842.4189 • ozotech.com
following procedure must be followed to ensure accurate
the product to ensure against shipping damage.
shipping package.
for damage or loss of equipment in transit.
PREPAID.
associated with the repair.
17.
OZOTECH, Inc. • 1015 South Main Street, Yreka, CA 96097 • Ph. 530.842.4189 • ozotech.com
10.0 Illustrations
18.
Figure 1: EOG internal layout
OZOTECH, Inc. • 1015 South Main Street, Yreka, CA 96097 • Ph. 530.842.4189 • ozotech.com
Maintenance Notes
Other manuals for EOG 200
1
Table of contents
Other Ozotech Oxygen Equipment manuals
Popular Oxygen Equipment manuals by other brands
John Bunn
John Bunn JOHN BUNN JB0150-085 instructions
DeVilbiss
DeVilbiss PD1000 Instruction guide
Invacare
Invacare IRC5PO2AW Service manual
Amtrol
Amtrol EXTROL 100 LBC Installation & operation instruction
Inova Labs Inc.
Inova Labs Inc. LifeChoice owner's manual
C-Aire
C-Aire FreeStyle 5 Quick reference guide
