Palram 700492 User manual

Overall Dimensions including base (Approx)
We strongly recommend the use of work gloves during assembly . Do not attempt
to assemble the greenhouse in windy or wet conditions.
Donottouchoverheadpowercableswiththealuminumprofiles.Alwayswearshoes
and safety goggles when working with extruded aluminum. Dispose of all plastic
bags safely - keep them out of reach of small children. The greenhouse must be
positionedandfixedonaflatlevelsurface.Donotleanagainstorpushthegreenhouse
during construction. Keep children away from the assembly area. Do not position
your greenhouse in an area exposed to excessive wind.
Do not attempt to assemble this greenhouse if you are tired, have taken drugs or
alcoholor if you are prone to dizzy spells. If using a step ladder or power tools ensure
thatyou follow the manufacturerssafetyadvice. Hot items suchasrecently used grills,
blowtorches etc. must not be stored in the greenhouse. Ensure there are no hidden
pipes or cables in the ground before inserting the pegs.
This is a multi-part assembly. Allow at least 180 minutes for assembly process.
Selecting a site - choose a sunny level position away from overhanging trees. If you
are fixing your greenhouse directly to a solid concrete foundation use the pre drilled
holes in the metal base supplied.The component parts should be checked and laid
out close at hand. Keep all small parts (screws etc.) in a bowl so they do not get lost.
Keep roof clear of snow and leaves.
Whenyourgreenhouse needs to be cleaned, use a mild detergentsolutionand rinse
with cold clean water. DO NOT use acetone, abrasive cleaners or other special
detergents to clean the clear panels.
Replacement parts - contact Customers service helpline at:
For additional information please visit our web site: www.palram.com
Tape measure
Work gloves
Crosshead screwdriver
Bradaw
Drill
2mm metal drill bit
Scissors
Step ladder
Spirit level
If help is required seek professional advice whithin store.
LEAN-TO
Greenhouse
ASSEMBLY INSTRUCTIONS
129L x 71W x 165H CM
Keep these instructions in a safe place for future reference.
You must read these instructions carefully before you start to assemble
this greenhouse. Please carry out the steps in the order set out in these
instructions.
Do not tighten the screws of the Greenhouse until completing on the
assembly of the panels.
IMPORTANT
SAFETY ADVICE
GENERAL ADVICE
CARE & MAINTENACE
TOOLS & EQUIPMENT
Version #3

Contents
Item Qty.
mm/inc. Item Qty.
mm/inc. Item Qty.
A7011190mm/46.85”
A702 670mm/26.38” 1
1
A711 1200mm/47.24”
A712 200mm/47324”
A715 680mm/26.77”
A716 680mm”26.77”
1
1
1
1
A731 1233mm/48.54” 1
A741 1233mm/48.54” 1
A791 615mm/24.21” 2
A721 1472mm/57.92”
A722 1472mm/57.92” 1
1
A761 1233mm/48.54” 1
A782 585mm/23.03” 2
A752 585mm/23.03” 1
A771 1180mm/46.46” 2
A751 585mm/23.03” 1
A754 610mm24.02” 2
M745 RIGTH
M746 LEFT
M747
1
2
4
2
2
2
M8x16mm/0.63” 2
.
1
1
1
1
3
1
P501
P502
P520
P519 1
P521
P522 1
1
1
3
4
2
30
30
8
4
2
M6x10mm/0.39”
M6x10mm/0.39”
M4x16mm/0.63”
M4
1220x610mm/48.03x24”
1220x610mm/44.69x24”
680x612mm/26.77x24.09”
650x610mm/25.59x24”
275X610 mm/19.83x24”
275x610 mm/19.83x24”
P316 100mm/3.94”
P317 50mm/2”
P304 20mm/0.79”
P303 1180mm/46.46”
A307
447
411
412
421
422
M307
1465 mm/57.68”
1190 mm/46.87”
1110mm/43.70”
660mm/26”
640mm/25.2”
P330
P331
P332
P333
P334
mm/inc.

745
746
A
B
447
747
C
412
412
A761
1
Assembly of base profiles:
Be sure to bend the profiles into 90 , and to tighten firmly with screws
447.
QTY
1
#A761
QTY
QTY
1
#M747
1
#M745
1
#M746

AssemblyofthecornersprofilesA711& A712:
Pay attention to set the profiles accordind to the detraction shown
on the profiles A711 during the assembly of profile A761.
NOTE: All nuts 412 should be on the inside of the stretcher,insert
the screws 411 from the outside inwards.
DO NOT FASTERN THE SCREWS AND NUTS until you complete
your greenhouse assembly.
Connect profiles A721,A722 to the base.
A711
A712
A712
A711
411
412
411
412
411
A761
411
412
A722 A721
32
QTY
1
#A711
1
#A712
QTY
1
#A721
1
#A722

AssemblyofprofileA754:
Be sure to use the lower hall of existing two. Assembly of the gutter A731 (The profile also includes the door track):
Be sure to locate the gutter as shown in the illustration.
A253
A754
411
412
A754
54
QTY
2
#A754
QTY
1
#A731
A731
412
A731
411

AssemblyofprofileA715andA716:
Connect the profiles as shown in the illustration. AssemblyoftheA741profiles: Connect the profile on both ends to profiles: A715 and A716, and
mark the connecting points (to the wall), using the pre-drilled halls
in the profile.
A716
A715
A715
411
412
411
411
76
QTY
1
#A715 1
#A716
A741
411
412
QTY
1
#A741

412
A702
411
411
A702
10
AssemblyofprofileA702ontheroof:
Connect the proile to profiles A741 on one side , and A731 on the
second side.
AssemblyofprofileA701onthefrontwall:
Connect the profile to the profile A731 on one sideand to profile
A761 on the second side.
A701
412
411
A701
412
411
98
QTY
1
#A701 1
#A702

Doorsub-assembly:
Insertrubberseal R303 into profiles A771. It is advisable tousesmall
amount of tender appropriate lubrication material. Connect profiles
A771 with profiles A791 using screws 421.
411
Doorsub-assembly(continued):
Lay panel P502. Be sure to insert both ends into the channel in
profiles A791.
P502
1110
QTY QTY
1
#P502
QTY
2
#A771 2 #A791
QTY
R303
A791
421
421
A771
A771 A771
2
#R303
A791

Connect plastic strips P332 on both sides of panel P502.
NOTE:Itisimperativetothreadintheplasticstrips.Ontothealuminum
profiles in it’s assigned position. See illustrations Ato D.
Doorsub-assembly(Continued):
Connectall four plastic rollers P304 using screws 421 and nuts 422.
A
B
C
C
D
A
B
C
D
P332
P332
Assembly follows illustration.
421
422
P304
421
P304
422
1312
QTY
2
#P332
QTY QTY
4
#P304 4
#421 4
#422

A731
412
411
A761
Assemblyofthedoortowallpanels:
Slid the door unto the track on frofile A731 (gutter), and on
thesame time on proffileA761.Inserttwo screws, 411& nuts
412 on both ends of profile A731.
Assembly noise reduction profile P317 to wall panels.
P317 P317
1514
QTY
3
#P317
QTY
1
#A731