Palram SUNTUF Ez-Glaze User manual

AestheticsWind ResistanceUV Resistance Easy To InstallSnow Load
SUNTUF®Ez-Glaze Installation Guide
PALRAM Webseite
SUNTUF® Ez-Glaze - Product Page

SUNTUF® Ez-Glaze Installation Guide
2
Installation
1000mm
50mm
Rafter spacing Foamed tape application (optional).
Placing the 1st SUNTUF Ez-Glaze panel
Minimum Roof Slope
1
2
To ensure proper water runoff, slope should be at least 5% (50mm rise over 1m length).
Distance between rafters must be 600 mm (center to center).
Make sure the rafters are perfectly perpendicular to the beams/wall.
SUNTUF EZ-Glaze requires rafters support only, no purlins are required. Applying foamed tape on each rafter will reduce friction due to thermal expansion.
3
4
600mm
Place the first SUNTUF Ez-Glaze panel on the rafters, leaving 50-150mm overhang.
Pre-drill 10 mm holes along the outer corrugation, every 500mm.
1st and last drills should be located 30mm-50mm from the rafter’s top and bottom edges.
Foam tape
90o
500mm
30-50mm
50-150mm

SUNTUF® Ez-Glaze Installation Guide
3
Installation
Fixing the 1st SUNTUF Ez-Glaze panel Fixing the 2nd SUNTUF Ez-Glaze panel
Completing the installationPlacing the 2nd SUNTUF Ez-Glaze panel
5
Fix both panels overlap, using specified screws and washers through the pre-drilled
holes. Start at the bottom edge and work your way up.
Repeat stage 6 & 7 with the remaining panels.
Fix the first SUNTUF Ez-Glaze panel’s outer corrugation, using specified screws and
washers through the pre-drilled holes. Start at the bottom edge and work your way up.
Place the second panel, lateral overlapping the first one.
Pre-Drill both panels together on the lateral overlap, every 500mm.
7
86
500mm
Use Self-Tapping screw
50mmx6.5mm
with 25mm EPDM washer

- 07.2020
Safety comes first
Do not step directly on the sheets between the rafters!
When installing SUNTUF Ez-Glaze or doing maintenance work, always use
stepping ladders or crawling boards, supported by minimum three roof
structural elements.
*
Metal Flashing
Screws to Wood rafter
Packer
Metal Flashing
Aluminum "F" prole
Ez-Glaze
Gasket
Screws to Wood rafter
Metal Flashing
Screws to Wood rafter
Packer
Aluminum "F" prole
Ez-Glaze
Gasket
Screws to Wood rafter
Metal Flashing
Screws to Wood rafter
Packer
Metal Flashing
Aluminum "F" prole
Ez-Glaze
Gasket
Screws to Wood rafter
Metal Flashing
Screws to Wood rafter
Packer
Aluminum "F" prole
Ez-Glaze
Gasket
Screws to Wood rafter
Installation
Side Wall Flashing in case the panel is trimmed (Not supplied by Palram)
PALRAM NSW/ACT
Unit 2, 26 Redfern St.
Wetherill Park, NSW 2164
Tel: [phone]
Fax: [phone]
[email protected]
PALRAM QLD
Unit 9C / 380 Bilsen Road
Geebung QLD 4034
Tel: [phone]
Fax: [phone]
[email protected]
PALRAM SA/NT
517A Cross Keys Road
Cavan SA 5094
Tel: [phone]
Fax: [phone]
[email protected]
PALRAM VIC/TAS
34 Buys Court
Derrimut VIC 3030
Tel: [phone]
Fax: [phone]
[email protected]
PALRAM WA
74 Christable Way
Landsdale WA 6065
Tel: [phone]
Fax: [phone]
[email protected]