Panasonic EX-Z Series User manual

Ultra-minute Photoelectric Sensor
EX-Z Series
USER’S MANUAL
WUME-EXZ-1
Phone: [phone] - Fax: [phone] - Web: www.clrwtr.com - Email: [email protected]

2
Contens
1. Cautions··························································································3
2. Part Description ················································································4
3. Mounting ·························································································5
3-1 Mounting of sensor················································································· 5
3-2 Installation interval ················································································· 7
4. I/O Circuit Diagram············································································9
5. Stability Indicator·············································································10
6. Beam Alignment·············································································· 11
7. Option···························································································12
7-1 Sensor mounting bracket········································································12
8. Specications ·················································································13
8-1 Side sensing type ·················································································13
8-2 Front sensing type ················································································14
9. Dimensions····················································································15
Phone: [phone] - Fax: [phone] - Web: www.clrwtr.com - Email: [email protected]

3
1. Cautions
WARNING
●Never use this product as a sensing device for personnel protection.
●When using sensing devices for personnel protection, use products that meet laws
and standards, such as OSHA, ANSI or IEC etc., for personnel protection applicable in
each region or country.
●This product has been developed / produced for industrial use only.
●This product employs a small cable of 0.1mm2in conductor area. Take care that the
cable is not pulled with a strong force, as it may damage this product or break its wires.
●Make sure that stress by forcible bend or pulling is not applied to the sensor cable joint.
● Cable can be extended up to 50m in total length (each emitter / receiver of thru-beam
type) if extension cable is more than 0.3mm2in electric conductor cross-sectional area.
●Make sure that the power supply is OFF while adding or removing the controllers.
●Take note that incorrect wiring will damage the sensor.
●Verify that the supply voltage variation is within the rating.
●If power is supplied from a commercial switching regulator, ensure that the frame ground
(F.G.) terminal of the power supply is connected to an actual ground.
●When noise generating equipment (switching regulator, inverter motor, etc.) is used in
the vicinity of this product, connect the frame ground (F.G.) terminal of the equipment to
an actual ground.
●Do not run the wires together with high-voltage lines or power lines or put them in the
same raceway. This can cause malfunction due to induction.
● Take care that the sensor is not directly exposed to uorescent lamp from a rapid-starter
lamp, a high frequency lighting device or sunlight etc., as it may affect the sensing per-
formance.
●Do not use during the initial transient time (50ms) after the power supply is switched
ON.
●This product is suitable for indoor use only.
●Avoid dust, dirt, and steam.
●Do not use this sensor in places where it may come in contact with corrosive gas, etc.
●Ensure that the product does not come into contact with organic solvents such as thin-
ner.
●Ensure that the product does not come into contact with strong acid or alkaline.
●Ensure that the product does not come into contact with oil or grease.
●This product cannot be used in an environment containing inflammable or explosive
gases.
●Never disassemble or modify the product.
●Cable end has not been waterproofed. Do not use the product in any manner that may
cause water entry via cable end.
Phone: [phone] - Fax: [phone] - Web: www.clrwtr.com - Email: [email protected]

4
2. Part Description
Thru-beam emitter side sensing type EX-Z11□, EX-Z12□, EX-Z13□
Beam emitting part
Thru-beam receiver side sensing type EX-Z11□, EX-Z12□, EX-Z13□
Operation indicator (Orange)
Lights up when the sensing output
is ON.
Beam receiving part
Stability indicator (Green)
Lights up under the stable light condition
or the stable dark condition
Thru-beam emitter front sensing type EX-Z11F□, EX-Z12F□, EX-Z13F□
Beam emitting part
Thru-beam receiver front sensing type EX-Z11F□, EX-Z12F□, EX-Z13F□
Operation indicator (Orange)
Lights up when the sensing
output is ON.
Beam receiving part
Stability indicator (Green)
Lights up under the stable light condition
or the stable dark condition
Phone: [phone] - Fax: [phone] - Web: www.clrwtr.com - Email: [email protected]

5
3. Mounting
3-1 Mounting of sensor
●The tightening torque should be 0.2N·m or less.
● M2 screw and nut, spring washer, and at washer are accessory of this product.
When tapping in mounting section (Unit: mm)
<Side sensing type>
Sensing
direction
8.5
M2 screw (length 10)
(accessory)
M2×0.4
Tapping depth: 5
<Front sensing type>
Sensing
direction 8.5
M2 screw (length 6)
(accessory)
M2×0.4
Tapping depth: 7
When using screws and nuts that are accessory of the product (Unit: mm)
<Side sensing type>
Sensing
direction
8.5
M2 screw (length 10)
(accessory) Thickness of mounting plate: 2 or less
Nut
Spring washer
Flat washer
Thickness of mounting
plate: 2 or less
Nut
Spring washer
Flat washer
<Front sensing type>
Sensing
direction 8.5
M2 screw (length 6)
(accessory)
Phone: [phone] - Fax: [phone] - Web: www.clrwtr.com - Email: [email protected]