Panasonic KX-TD816 User guide

Digital Super Hybrid System
KX-TD816
KX-TD1232
Installation Quick Guide
for
KX-TD7590CE

2
Table of Contents
1.0DECT Programming (PS Registration)........................................................................3
2.0Site Survey.................................................................................................................7
Note
This guide shows you the additional features for the DECT Portable Station (KX-TD7590)
Please refer to this guide in addition to the current installation Manual.

3
1.0 DECT programming
[650] PS Registration
Description
Assigns a registration number and an extension number to each PS. Display PT and the PS
whose registration number is to be set are required for this programme.
Selection
(With a display PT)
• PS registration number:
KX-TD816 – 01 through 16
KX-TD1232 – 01 through 64
• PS extension number: 2 through 4 digits
(With a PS)
• DECT system number: 1 through 4
•PSpassword:4 through 8 digits
• System lock password: 1 through 4 digits
Default
All PSs – Not Stored
Programming
[Registering for the first time]
(With a display PT)
1. Enter 650.
Display: PS Registration
2. Press NEXT.
Display: PS NO?
3. Enter the PS registration number.
Display example: PS01:Not Stored
4. Enter the PS extension number.
Display example: PS01:Ext 281
5. Press STORE.
Display (If enabled): Executing
Continue programming from step 6 with a PS within five minutes.

4
Display (If disabled): Rejected
The Cell Station (CS) may not be connected or not working. After connecting the CS
or resetting the PBX, wait for at least one minute and try again from the beginning.
6. Press the POWER button for a while (about 5 seconds).
7. Press the FUNCTION button.
8. Press the FUNCTION button again.
Or Press the UP/DOWN button repeatedly until “PROGRAM” is selected and then press the
SELECT button.
9. Press the UP/DOWN button repeatedly until the display below is selected.
Display: INITIAL SETTING
10.Press the SELECT button.
11.Press the UP/DOWN button repeatedly until the display below is selected.
Display: REGISTRATION
12.Enter the SELECT button.
13.Press the UP/DOWN button repeatedly until the desired DECT system number is
selected.
Display example:REGISTRATION
DECT-SYS 1
DECT-SYS 2
14.Press the SELECT button.
15.Enter the PS password.
16.Press the AUTO/OK button.
You will hear a confirmation tone and the display changes as follows.
Display example: DECT-SYS LOCK
ENABLE
DISABLE
17.Enter the UP/DOWN button to select “DISABLE” or “ENABLE” for the System Lock.
Display example: DECT-SYS LOCK
(With a PS)
Display example: ENTER PASSWORD
=--------
Display example: ENTER PASSWORD
=****----
Display: EXECUTING

5
ENABLE
DISABLE
18.Press the SELECT button.
Display example:
19.If you select "ENABLE" in step 17, enter a System Lock password.
20.Press the AUTO/OK button.
21.Enter the System Lock password again.
22.Press the AUTO/OK button.
23.To programme another PS, press NEXT or PREV, or SELECT and the desired PS
registration number.
24.Repeat steps 4 through 22.
25.Press END.
[Re-registering] (e.g. when changing the DECT system)
1. Repeat steps 1 through 8 of the “Registering for the first time” programming.
2. Press the UP/DOWN button repeatedly until the display below is selected.
Display: PS-PROGRAM
3. Press the SELECT button.
4. Press the UP/DOWN button repeatedly until the display below is selected.
Display: DECT-SYS SETTING
5. Press the SELECT button.
If a System Lock password is registered before, the display below will appear.
(if disabled):
(if enabled) :
UNLOCKED
ENTER PASSWORD
=----
Display: ENTER PASSWORD
=****
Display: REENTER PASSWORD
=----
Display: REENTER PASSWORD
=****
Display: LOCKED
(With a display PT)

6
Display example: DECT-SYS LOCK
PASSWORD =----
6. Enter a System Lock password and press the AUTO/OK button, if required.
Display: DECT-SYS LOCK
PASSWORD =****
7. Go to steps 11 through 25 of the “Registering for the first time” programming.
Conditions
• You can assign an extension number to each PS also in programme, [671] PS Extension
Number Set.
• The PS password can be assigned in programme [672] PS Password Set.
• One PS must have only one registration number. It is not possible to assign the different
registration number for one PS.
• If the PS extension number or the PS password is changed after registering, the PS cannot
be used until it is registered again in this programme.
• After pressing the AUTO/OK button in step 16, do not press END before you hear a
confirmation tone, or it may not registered correctly.
• To re-assign the PS, which is set the System Lock, to the other DECT system, it is required
to cancel the System Lock first in PS Programming, “DECT System Lock Password Set.”
• Register the PS from a manager DPT connected only to the master cabinet.

7
2.0 Site survey
Assigning the Cell Station ID Number to the PS
1. Keep pressing , and until following message will be displayed.
Display: FUNCTION (0-4)?
2. Press .
• When the Cell Station ID Number is assigned, it is displayed on the bottom line.
Display example: CS-ID SET
CS NO.(0-7)?
3. Enter the Cell Station number (0 through 7).
Display example: CS-ID SET
CS NO.(0-7)? 0
4. Press .
Display example: CSID0=
----->
5. Enter the Cell Station ID Number (0 through 9 and A through F).
• To erase a ID Number or letter, press .
• To enter letters, press the following buttons.
Display example: CSID0=
----->9005301234
6. Press .
• The assignment is completed.
Display example: CS-ID SET
CS NO.(0-7)?
0
7. Repeat steps 3 through 6 to assign other Cell Station ID numbers.
8. Press to return to the initial display.
Display: FUNCTION (0-4)?
199
2
ABC
CLR
A
(Flexible CO)
B
C
D (Intercom)
E (Auto/OK)
(Function)
F
F1
F2
(Flexible CO)
F3
(Flexible CO)
INT'
OK

8
Note
• To return to the previous display, press .
Deleting the assigned Cell Station ID Number on the PS
1. Keep pressing , and until following message will be displayed.
Display: FUNCTION (0-4)?
2. Press .
Display example: CS-ID CLEAR
CS NO.(0-7)?
(#=ALL CLEAR)
3. Enter the Cell Station number (0 through 7).
Display example: CS-ID CLEAR
CS NO.(0-7)? 0
(#=ALL CLEAR)
4. Press .
• If you pressed # (ALL CLEAR) on step 3, the display return to the initial display.
Display example: CS-ID0=9005301234
ARE YOU SURE?
Y=TALK N=CANCEL
5. Press .
6. Repeat steps 3 through 5 to delete other Cell Station ID numbers.
7. Press to return to the initial display.
Display: FUNCTION (0-4)?
Note
• To return to the previous display, press .
199
3
DEF

9
Unplugging the Cable from the Cell Station
After assigning the Cell Station ID number to the PS, unplug the cable from the Cell Station
once.
DIP-Switch Setting
After unplugging the Cell Station once, set the DIP-Switch as follows.
1. Switch the Radio Signal Test Switch from OFF to ON.
2. Set the Channel Number Switches as desired.
01
01
01
01 01
01
Channel 1
1234
Channel 4
1234
Channel 7
1234
Channel 2
1234
Channel 5
1234
Channel 8
1234
Channel 3
1234
Channel 6
1234
Channel 9
1234
01
01
01 01 01 01
DIP-Switch
10 10 10 10 10 10
ON
123456
OFF
Radio Signal
Test Switch
Channel Number Switch
(Default: Channel 0)

10
Note
• To see the signal strength of more than one Cell Station, the channel for each Cell Station
needs to be set.
• Up to eight Cell Stations can be surveyed at the same time. If more than one Cell Station is
in Radio Signal Test mode, each DIP-Switch channel must be different.
Connecting the AC Adaptor to the Cell Station
After setting the DIP-Switch, connect the AC Adaptor (KX-A11BS1: 230 VAC, 50 Hz) to the
Cell Station.
Note
Only use the AC Adaptor for the Site Survey.
Radio Signal Test using the PS
After locating the Cell Station(s) temporarily, execute the Radio Signal Test using the PS.
The PS scanswhether there is a Cell Station that canlink with on channel 0 right after entering
the Radio Signal Test mode. The channel to be scanned can be changed by pressing the
appropriate 0 through 9 keys.
1. Keep pressing , and until following message will be displayed.
Display: FUNCTION (0-4)?
2. Press .
•To survey other slots, scroll by pressing (Previous) or (Next).
•To survey other channels, enter the channel number (0 through 9).
Display: RADIO STRENGTH
<<<MEASURING>>> <--flashing while testing
Note
• To return to the previous display, press .
199
00