Panasonic DL-EH30SE-W User manual

Preparation Installation Commis
sioning
Reference
Installation Steps 6
Installation of Water Inlet Hose on Shunt
Valve Side 6
Installation of electric bidet seat 7
Installation of Water Inlet Hose on Body Side 8
Installation Instructions
Electric Bidet Seat
(Household Use)
Model DL-EH30SE-W
S0822-0
Issued August 2022
Safety Cautions 2
Cautions Before Installation 3
Part Names and Accessories 4
1
2
3
4
Page
Contents
Commissioning 10
Troubleshooting Back Cover
Read the Installation Instructions carefully before installing the product in a correct and safe manner.
Make sure to read the “Safety Cautions” on Page 2 before installation.
● We shall not be held liable for any incident or damage arising out of any installation other than those
described in the Installation Instructions or use of parts other than those specified.
● The actual product may be different from the illustrations and descriptions.
ADL944PZYXC0

2
Safety Cautions
To prevent any personal hazard or property damage, make sure to follow the instructions below.
The hazard or damage caused by misuse can be categorized by the following degrees.
indicates a potential hazardous situation where death or severe injury
may be suffered if not avoided.
indicates a potential hazardous situation where mild or moderate injury
may be suffered if not avoided.
Do not connect any water pipe other than the pipe for tap water.
(Risk of cystitis or dermatitis)
(Risk of water leak due to corrosion or attached foreign objects)
Do not supply power to the product by any external switch.
(There is a risk that the temperature limiter will return to error)
Do not damage the power cord and plug.
(Otherwise, electric shock or fire from short circuit may be incurred.)
Do not plug or unplug the power plug with wet hands.
(Otherwise, electric shock my be incurred.)
Do not place any burning objects, including cigarette, near the product.
(Risk of electric shock or fire)
Do not apply any pressure to the body connection, for example, falling.
(Otherwise, crack or water leak may be incurred.)
Install water pipes by following the regulations imposed for your place
of residence.
(Otherwise, water leak may be incurred.)
When moving or installing the bidet, hold the body with both hands.
(If you move it by holding the seat or lid, it may fall off from the body and cause injury.)
Body connection
Make the ground connection.
(Risk of electric shock may be incurred in the event of any fault and electrical leakage if not grounded.)
→Please consult a professional for the ground connection.
Plug the power plug all the way in.
(If it is not plugged completely, electric shock or fire from heating may be incurred. Do not use a damaged plug or a loose
wall socket.)
Comply with relevant electrical regulations when working on any electric circuit.
(Otherwise, fire or electric shock may be incurred.)
Make sure to perform installation by following the instructions in the Installation Instructions.
(Otherwise, water leak, fire or electric shock may be incurred.)
Make sure to use supplied or specified parts during installation.
(Otherwise, water leak, fire or electric shock may be incurred.)
Make sure to follow the range of the wall socket’s and connection apparatus’ ratings. Only use
220-230 V AC power.
(Risk of fire due to heating)
WARNING
CAUTION
WARNING
CAUTION

3
Cautions Before Installation
Preparation
Required Tools
Tape measure Phillips screwdriver Adjustable wrench Bucket and rag
As the product has undergone the water passage test, a small amount of water remaining inside may flow out.
This is not a malfunction.
The operating range of water pressure is 49 - 735 kPa｛0.5 - 7.5 kgf/cm2｝.
Shaking may sometimes result from seat mounts not contacting with the surface of the toilet depending on
toilet types.
Tips
Note Do not plug the power plug before the bidet body is installed completely. Otherwise, a malfunction may
be incurred.
When the water remaining inside the body is frozen, move the body to a warm place. Perform installation
after the frozen water is thawed out.
Make sure to use the supplied water inlet hose. Otherwise, a water leak may be incurred.

4
Part Names and Accessories
Gasket set
(Black gasket *2 , included
in the bag for )
Quick fastener
(Included in the bag for )
4 mm×12.5 mm×1
4 mm×12.5 mm×1
Water inlet hose with
shunt valve
(Length: 950 mm)
Instructions package
(Refer to the List of Parts for details in the next page.)
Top-mounted bolt set
Shunt valve
Water inlet hose
Water inlet valve
Lid
Power plug
Seat
Power indicator
Occupancy Switch (built-in)
[Positions to install gaskets]
Electrical leakage
test button
The thickness of the gaskets
are consistent with actual
products.

5
Preparation
No. Part name
Water inlet hose with shunt valve
Gasket set
Quick fastener
Top-mounted bolt set
Thin type: black, 2.5 mm thick ×1
Thick type: black, 4 mm thick ×1
Instructions package
Operation Instructions
Installation Instructions
Confirmation card of water release
outlet position
Qty. Verification
[Accessories] Check if there is any missing or lost part.
1
1
1
1
1
(Included in the bag for )
(Included in the bag for )
Do not use any sealing tape when connecting the shunt valve.
(Risk of water leak can result from the sealing tape stuck on a gasket)
Make sure to use supplied gaskets and quick fastener.
(Risk of serious water leak if these are ignored or other parts are connected
during installation)
WARNING

6
Installation Steps
Installation of Water Inlet Hose on
Shunt Valve Side
1 2 3
Installation of Water Inlet Hose on
Shunt Valve Side Page 6
Installation of electric bidet seat Page 7
Installation of Water Inlet Hose on
Body Side Page 8
Page 10Commissioning
Close the water inlet
valve and remove the
water inlet pipe.
Attach the shunt valve on the water
inlet hose to the water inlet valve.
Re-install the water inlet pipe.
Water inlet
pipe
Remove
Close
Use an adjustable wrench or pliers to
secure this position
Tighten with a
wrench at the
same time
Acorn nut
aligned with
the valve
Shunt valve
connection
Acorn nut
Water inlet pipe
Secure from the
bottom side with an
adjustable wrench
Tighten
Water inlet valve
Illustrated parts are those
mentioned in page 4
Water inlet hose
Water tank of
the toilet
Water inlet valve
Gasket
(Black, 2.5 mm thick)
Gasket
(Black, 4 mm thick)
Water inlet valve
Do not secure any part other than those specified
with the tool to prevent any water leak due to
damage.
Do not scratch the connection of the shunt valve
to prevent any water leak.
Do not hold the water inlet hose by your hands to
prevent injury when turning the acorn nut.
Tips

7
Installation of electric bidet seat
Installation
Remove the installed old seat.
Install the body mounting plate. Install the body.
1. Loosen the bolt and remove the nut. (Fig. 1)
1. Align the protrusion in the center on the back side of
the body with the one in the center of the body
mounting plate.
2. Lift up the rear part of the body slightly and slide it
towards the body mounting plate until a “click” is
heard.
●Do not secure the power cord between the body and toilet.
With a tape measure, measure the length of A. (Fig. 3)
Align the center line of the top-mounted bolt with the
reference scale line matching A on the body mounting
plate for preliminary positioning. (Fig. 4)
2. Fit the metal mounting plate to the top-mounted bolt
and screw in the nut. (Fig. 2)
(This nut is applicable to toilet with the bore diameter
of 12 - 17 mm . For other bore diameters, consult our
after-sales service for installation.)
3. For preliminary positioning, secure the top-mounted
bolt to the body mounting plate. (Same on both sides)
Perform the removal operation by
following the Instructions provided
by the purchased toilet.
Remove the body mounting plate.
Press the body assembly / disassembly
button all the way in and remove the
body mounting plate.
(Pull out along the direction of
arrows alternatively.)
490
440
490
440
1
34
When the rear part of the lid contacts the water tank
of the toilet, or the lifted seat falls down easily.
Move the body mounting plate forwards slightly and
secure it. Install the body again.
A
490
440
490
440
490
440
490
440
B 80 mm
2
4. Adjust the position of the body mounting plate and
ensure B 80 mm. Then, install the body mounting plate
to the toilet.(Fig. 5)
490
440
Example
Bolt
Bolt
Protrusion
Front seat mount
Nozzle compartment
Protrusion
Center line
Tighten
(Example of
A=490 mm)
Nut
Remove
Toilet mounting
hole
Top-mounted
bolt
Metal mounting
plate
Loosen
Fig. 1 Fig. 2
Fig. 4
Fig. 5
Fig. 3
Unscrew
Body assembly /
disassembly button
Seat
Do not press the nozzle
compartment.
(Otherwise, the nozzle may get
stuck.)
The spacing for installing the bolts of the body mounting
plate can be adjusted between 130 - 215 mm.
Do not place the nozzle
compartment at the body base
on the surface of the toilet.
Make sure the front seat mount
is placed on the surface of the
toilet.
Make sure to install the body mounting plate with
B 80 mm. Otherwise, the body may be tilted or a
water leak may occur.
Once the body is installed, lift it up gently to check if it is
installed securely.
As this product is design with a detachable structure to
enable the body to be removed from the toilet, it may
sometimes feel slightly shaky. This is not a malfunction.
For proper installation, be sure
to use the body mounting plate
supplied with the product.

8
Installation of Water Inlet Hose on Body Side
Connect to the body
1. As illustrated, insert the O-ring side of the
water inlet hose straight into the body
connection port.
(If not inserted straight, the O-ring may
be damaged.)
2. As illustrated, insert the quick fastener
all the way into the connection correctly
until a “click” is heard.
Bend Tighten
Claw end
Hold end
Connection Insert
Body
connection
port
Quick fastener
Bend
Turn gently
Turn to a easily
visible position
and fit the claw.
Make sure to use the water
inlet hose supplied with the
product.
(Risk of water leak)
A
3. Tighten the claw securely.
Bend the hole end downwards.
Bend the claw end towards the hole end
and tighten it. (Until a “click” is heard)
4. With the water inlet hose held in your hands,
turn the quick fastener gently. The turning
operation should be smooth. (If it is not
smooth, it indicates the installation is
done improperly.)
Caution:
Serious water leaks may occur if the water inlet hose is installed improperly.
Note
An O-ring must be fitted to the
front end.
The O-ring must be free of dust.
(Risk of water leak)
Caution
Do not damage (cut or scratch)
the water inlet hose.
(Risk of water leak)
Caution
When the claw can’t be fit, it
indicates that the connection isn’t
inserted all the way in.
Make sure the insert and tighten
the quick fastener securely.
* If the claw is not tightened securely,
the quick fastener will become
loosened, resulting in a serious water
leak.
Note
About the O-ring
About the
quick fastener
Example of incorrect connection
O-ring
Water inlet hose
Claw not
tightened
1

9
Installation
Body connection
Water inlet
hose Quick
fastener The direction can be
changed with ease
<Horizontal view>
Make sure to
2
3
Check if the quick fastener is secured firmly.
Pull the water inlet hose gently to check if it will not separated from the body.
Open the water inlet valve.
During installation, the body connection can be turned.
Once all ports are connected and verified,
open the water inlet valve. Water inlet valve
Open
The direction of
the connection
can be changed
When the bathroom is confined and it is difficult to install the water inlet hose after the bidet body is
installed, you can attach the water inlet hose to the body first, and then install the body to the toilet.
Tips
(To 120°)

10
Commissioning
2 4 5
Power plug
Cover with a plastic film or similar device.
(Between the seat and toilet)
Check if the power plug is
plugged.
(The Power indicator is on.)
Press and hold the Electrical Leakage Test button for
2 seconds or longer.
Before Commissioning……Check if the water inlet valve is opened. (Volume adjustment will be affected if it is not
opened.)
Check if there is any water leaked from the connection.
The electrical leakage detection function is activated and
power is cut off. (The Electrical Leakage indicator is on
and the Power indicator is off.)
Unplug the power plug.
Check if the Electrical Leakage
indicator is off.
After 5 seconds, plug the power plug.
The Power indicator will flash for approximately
10 seconds before remaining on.
Check if the water temperature is set to “Off”.
Press or
[Do the followings]
The nozzle extends and the warm water tank of the body begins to pump in water. After approximately 1 minute,
water will flow out from the nozzle downwards. If no water flows out, check if the main water valve is opened or
the water inlet valve isn’t opened sufficiently.
When carrying out Step , the warm water tank is running idle if the “High”, “Mid” and “Low” Water
Temperature indicators all flash. This is not a malfunction.
Open the main water valve and water inlet valve. Start commissioning from Step again.
(The Water Temperature indicator is off.)
Off
Off
Off
On
6
6
1
2
3
5
4
6
110
8
When the Electrical Leakage indicator flashes, unplug the power plug immediately and contact your dealer or
one of Panasonic-operated service centers.
If you touch a closed seat (the Occupancy indicator is on and deodorization operate and unintentionally press the Rear
Showering / Front Showering button, water will come out and spray on yourself.
Tips
About idle running in the warm water tank
Occupancy
switch (built-in)
Plastic film
Step
On
On

11
Commis
sioning
Press
The nozzle retracts.
Press
Remove the plastic film.
Once the nozzle retracts, water for nozzle self-cleaning will come out.
Press and to set the temperature. After 5 -12 minutes, sit at the seat to check the seat
and water temperature.
It takes approximately 5 - 12 minutes for the temperature of the seat and warm water to stabilize.
(Depending on ambient temperature and the temperature of tap water.)
Press and hold the rear left portion of the seat. (The Occupancy indicator is on.) Meanwhile,
press or
Deodorization starts. (with motor sound)
The nozzle starts self-cleaning. After approximately 5 - 8 seconds, cleaning water will be sprayed.
(If the Occupancy Switch is not enabled, no water will be sprayed.)
Check if cleaning water is sprayed normally with the plastic film.
7
8
9
10
3
78
911
6
12
Press and hold the rear left portion of the seat.(The Occupancy indicator is on.) Meanwhile,
Press , confirm warm air function , then press .
11
After showering stops, droplets will fall from around the nozzle. These are the water resulted from thermal expansion
of the warm water tank or water remaining in the nozzle. This is not a malfunction. (Approximately 7 - 8 minutes after
showering)
The back mount of the seat and the front leg are floating It is normal.
If this gap is not present, seating detection will not be detected.
The Occupancy Switch is enabled when the seat is occupied
Occupancy indicator
Water release outlet
There is a gap
About releasing water
The water flowing out next to the nozzle (water release
outlet) is the one released for pressure adjustment.
This is not a malfunction.
If the water release outlet is placed on the surface
of the toilet, water may not flow into the toilet. At
this time, install the body sightly forward. [Page 7]

8
6
8
10
11
9
10
16
6
Symptom
Caution After Installation
The Water Temperature
indicator flashes
“High”, “Mid” and
“Low” at the same time
No water
Weak volume
adjustment
The inlet filter is clogged
Open the water inlet valve. Plug
the power plug again. Re-start
commissioning.
Clean the filter
screen with a
toothbrush
Open the water inlet valve
Tighten the nut
Adjust the positions of gaskets
Tighten it securely
Remove dust from the O-ring
Unplug the power plug. After 5
seconds, insert it back
Wait until the water tank of the
toilet finishes pumping in water
Open the main water valve sufficiently
The acorn nut isn’t tightened
Gaskets or other devices shift
The quick fastener is not tightened
During showering, the water flowing out next to the nozzle is the one released
for water pressure adjustment. This is not a malfunction.
The main water valve isn’t opened sufficiently
The water inlet valve isn't opened
The water tank of the toilet is
pumping in water, leading to low
water pressure
The O-ring on the
front end of the
hose has dust
The Electrical Leakage Test button
is pressed or electrical leakage
occurred(The Electrical Leakage
indicator on the body is on)
Water leaks from both
ends of the connection
of the water inlet hose
Power can’t be supplied
Water flows out from
around the nozzle
The Power, 8-hour
Power Saving and “Mid”
Water
Temperature indicators
on the body flash at the
same time
Ref. Page Possible Cause and Solution
The water inlet valve is not opened
The power plug is plugged before
the water inlet valve is opened
Does the power plug wiggle when being plugged or unplugged?
→Unplug the power plug. After 5 seconds, plug it back
When these indicators still flash after removing and inserting the power plug
several times, contact your dealer or one of Panasonic-operated service
centers
When the product is likely not to be used for more than 1 week, drain it.
(Refer to "When Not Used for A Long Time “ in the Operating Instructions.)
O-ring
Filter screen
Operation
Instructions
Malaysia
Panasonic Malaysia
Lot 10, Street 13/2, 46200 Petaling Jaya, Selangor Darul Ehsan.
'[phone]
E-mail: [email protected]
Service information
© Panasonic Corporation 2022
Printed in China
Troubleshooting