Panasonic VL-WD619 User manual

Getting Started
Wireless Monitor Station
Model No. VL-WD619
Thank you for purchasing a Panasonic product.
Please read this manual before using the product and save it for future reference.
Table of Contents
Introduction 2
Accessory information 2
General information 2
For your safety 3
Important safety instructions 4
Other important information 4
Battery installation 5
Charging the sub monitor 5
Wall mounting 6
Registering the product to the Video Intercom System 6
Cleaning 6
Specifications 6
© Panasonic Corporation 2020
PNQX9086ZA C0320MM0
1006, Oaza Kadoma, Kadoma-shi, Osaka 571-8501, Japan
http://www.panasonic.com
WD619-OI_en.book 1 ページ ２０２０年３月１２日 木曜日 午後３時３８分

2
Introduction
This product is an additional product designed to be used with the following Panasonic Video Intercom Systems.
– VL-SWD275 (Main monitor station: VL-MWD275)
– VL-SWD273 (Main monitor station: VL-MWD273)
– VL-SWD272 (Main monitor station: VL-MWD272)
– VL-SWD501BX (Main monitor station: VL-MWD501BX)
(The corresponding models are subject to change without notice.)
RYou must register this product with your Video Intercom System before it can be used.
RThe features that can be used with this product differ depending on the main monitor that it is registered to. For
information on usage after registration, refer to the Operating Instructions of your Video Intercom System.
RThis manual describes only the steps needed to register and begin using the product. Please read the Operating
Instructions of your Video Intercom System for further details.
RThe illustrations in the supplied manual(s) may vary slightly from the actual product.
RIn this manual, the suffix of each model number (e.g., the "BX" in "VL-WD619BX") is omitted unless necessary.
Product names used in this manual
Accessory information
Supplied accessories
*1 Only one of the AC adaptors is supplied.
*2 Please read the Operating Instructions of the Video Intercom System for information about replacement
batteries.
Note:
RYou will need the following additional items (locally procured) to install the charger on the wall.
– Screws x 2 (for wall mounting):
Prepare the screws according to the material, structure, strength and other factors of the mounting area and
the total weight of objects to be mounted.
RPlease read the Operating Instructions of the Video Intercom System for additional/replacement accessories.
General information
RIn the event of problems, you should contact your equipment supplier in the first instance.
Declaration of Conformity:
RPlease read "General information" section in the Operating Instructions of the Video Intercom System for
information regarding Directive 2014/53/EU.
Ecodesign information
RPlease read "Ecodesign information" section in the Operating Instructions of the Video Intercom System for
information regarding ErP directive.
Model No. Product name Name in this manual
VL-MWD275 Main monitor station Main monitor
VL-WD619 Wireless monitor station Sub monitor
Accessory item Quantity
AC adaptor/PNLV226CE, PNLV226E or PNLV226AL
*1
1
Rechargeable batteries
*2
2
Charger 1
WD619-OI_en.book 2 ページ ２０２０年３月１２日 木曜日 午後３時３８分

3
Graphical symbols for use on equipment and their descriptions
1. Alternating current (A.C.) 2. Direct current (D.C.) 3. Protective earth 4. Protective bonding earth 5. Caution: risk
caused by visible radiation 6. For indoor use only 7. Class Pequipment (equipment in which protection against
electric shock relies on Double Insulation or Reinforced Insulation) 8. "ON" (power) 9. "OFF" (power) 10. Stand-by
(power) 11. "ON"/"OFF" (power; push-push) 12. Caution, risk of electric shock
For your safety
To prevent severe injury or loss of life or property,
and to ensure proper and safe operation of your
product, read this section carefully before using
the product.
Preventing fire and electric shock
RUse only the power source marked on the
product. If you are not sure of the type of
power supplied to your home, consult your
dealer or local power company.
RUse only the specified AC adaptor.
RDo not attempt to disassemble or modify this
product. Contact an authorised service centre
for repairs.
RNever touch the AC adaptor with wet hands.
RDo not place objects on the power cables and
the AC adaptor. Install the product where no
one can step or trip on the power cables and
the AC adaptor.
RDo not allow the power cables and the AC
adaptor to be excessively pulled, bent or
placed under heavy objects.
RDo not overload the power outlet above the
specified levels. Overloading by having many
connections on one power outlet may cause
heat generation, resulting in a fire.
RNever put metal objects inside the product.
Never spill any liquid on the product.
If metal objects enter the product or the
product becomes wet, unplug the product from
the power outlet and contact an authorised
service centre.
RDo not use a microwave oven or other devices,
such as electromagnetic cookers, to speed up
the drying process of any parts of the product.
RCompletely insert the AC adaptor into the
power outlet. Failure to do so may cause
electric shock and/or excessive heat resulting
in a fire. Do not use damaged AC adaptors or
power outlets.
RRegularly remove any dust, etc., from the AC
adaptor by unplugging it from the power outlet,
then wiping it with a dry cloth. Accumulated
dust may cause an insulation defect from
moisture, etc., resulting in a fire.
RUnplug the product from the power outlet if the
product emits smoke, an abnormal smell or
makes unusual noise, or if the product has
been dropped or physically damaged. These
conditions can cause fire or electric shock.
Confirm that smoke has stopped emitting and
contact an authorised service centre.
RHold the main body (not the metal parts) of the
AC adaptor when unplugging it. Unplugging
the AC adaptor while holding its cord or the
cord’s plugs may result in fire, electric shock,
or injury.
Preventing accidents
RDo not use the product in health care facilities
if any regulations posted in the area instruct
you not to do so. Hospitals or health care
facilities may be using equipment that could be
sensitive to external RF (radio frequency)
energy.
RDo not install or use this product near
automatically controlled devices such as
automatic doors and fire alarms. Radio waves
emitted from this product may cause such
devices to malfunction, resulting in an
accident.
RConsult the manufacturer of any personal
medical devices, such as pacemakers or
hearing aids, to determine if they are
adequately shielded from external RF (radio
frequency) energy. (The product operates in
the frequency range of 1.88 GHz and
1.90 GHz with a peak transmission power of
250 mW (max.).)
123456
7 8 9 101112
WARNING
WD619-OI_en.book 3 ページ ２０２０年３月１２日 木曜日 午後３時３８分

4
Preventing fire and electric shock
RDo not use the product in areas that are
exposed to rain, moisture, steam, or oily
smoke, or areas that have excessive dust.
Preventing accidents, injuries, and property
damage
RDo not use the product in unstable areas or
areas prone to strong vibrations. This may
cause the product to fall, resulting in damage
to the product or injury.
RDo not put your ear(s) near the speaker, as
loud sounds emitted from the speaker may
cause hearing impairment.
RDo not place coins or other metal objects in the
charger. Metal objects may become hot,
causing burns.
RDo not place magnetic cards or other devices
that store data magnetically (such as credit
cards) near the charger. Failure to do so may
make the cards or devices unusable.
RThe speaker on the handset is magnetised and
may retain small metallic objects.
RTo prevent serious injuries due to the product
unexpectedly falling, the product with a wall
mount feature must be installed at a height of
2morlower.
Sub monitor batteries
Preventing leakage, heat generation, rupture,
or accidents
RWe recommend using batteries that match the
specifications of the batteries listed on page 6.
USE ONLY rechargeable Ni-MH batteries AAA
(R03) size.
RDo not mix old and new batteries.
RDo not open or mutilate the batteries.
Released electrolyte from the batteries is
corrosive and may cause burns or injury to the
eyes or skin. The electrolyte is toxic and may
be harmful if swallowed.
RCharge the batteries provided or identified for
use with the product only, in accordance with
the instructions and limitations specified in this
document.
RDo not heat batteries or dispose of batteries in
a fire.
RDo not touch the ends of batteries ( , ) with
metal objects.
RHandle the batteries with care. Do not allow
conductive materials such as rings, bracelets
or keys to touch the batteries, otherwise a
short circuit may cause the batteries and/or the
conductive material to overheat and cause
burns.
ROnly use the specified charger and AC adaptor
to charge the batteries. Failure to follow these
instructions may cause the batteries to swell or
explode.
RAvoid the use in the following conditions
– High or low extreme temperatures during
use, storage or transportation.
– Replacement of a battery with an incorrect
type that can defeat a safeguard.
– Disposal of a battery into fire or a hot oven,
or mechanically crushing or cutting of a
battery, that can result in an explosion.
– Extremely high temperature and/or
extremely low air pressure that can result in
an explosion or the leakage of flammable
liquid or gas.
Important safety instructions
When using this product, basic safety precautions
should always be followed to reduce the risk of fire,
electric shock, or personal injury.
1. Do not use this product near water. For example,
near a bathtub, wash bowl, kitchen sink, or laundry
tub, in a wet basement, or near a swimming pool,
etc.
2. Use only the AC adaptor and batteries indicated in
this document.
Do not dispose of the battery(ies) in a fire.
They may explode. Check with local codes for
possible special disposal instructions.
SAVE THESE INSTRUCTIONS
Other important information
RBefore attempting to connect or operate this
product, please read the nameplate on the bottom
or rear of the product.
RThe AC adaptor is used as the main disconnect
device. Ensure that the power outlet is installed near
the product and is easily accessible.
RSee the Operating Instructions of the Video
Intercom System for information about cautions in
regards to using the product and the installation
environment.
ROperating the product near electrical appliances
may cause interference. Move away from the
electrical appliances.
Caution:
RRisk of explosion if battery is replaced by
incorrect types. Dispose of used batteries
according to the instructions.
CAUTION
WD619-OI_en.book 4 ページ ２０２０年３月１２日 木曜日 午後３時３８分

5
Repairing, transferring, disposing, or returning the
product
Requesting repairs for the product
RNote that the settings of the product may be altered
or changed to the default settings during repairs.
Note for product disposal, transfer, or return
RPerform the "Initialize" setting for the product. (→
See the Operating Instructions of the Video
Intercom System.)
Settings are returned to their default values when
initialization is performed.
Information on Disposal in other Countries outside
the European Union
These symbols are only valid in the European Union. If
you wish to discard these items, please contact your
local authorities or dealer and ask for the correct
method of disposal.
Battery installation
– USE ONLY rechargeable Ni-MH batteries AAA
(R03) size.
– Do NOT use Alkaline/Manganese/Ni-Cd batteries.
– Confirm correct polarities ( , ).
Note:
RUse the supplied rechargeable batteries (Ni-MH
ONLY). When replacing batteries, we recommend
using batteries that match the specifications of the
batteries listed on page 6.
RWipe the ends of batteries ( , ) with a dry cloth.
RAvoid touching the ends of batteries ( , ) or the
unit contacts.
Charging the sub monitor
Only connect the charger with the supplied Panasonic
AC adaptor (→page 2).
*1 Press plug firmly.
RConnect the charger to the power outlet, and then
place the sub monitor in the charger to charge it.
Charging usually takes about 8 hours.
ACharge indicator
– when charging: lights
– when charging is completed: off
BHook
RCharge the sub monitor for at least 15 minutes
before registering it to the main monitor. Make sure
to completely charge the sub monitor after the
registration is completed.
RCharging may take longer in the following situations.
– When the operating temperature is low. (→
page 6)
– When the sub monitor is picked up off the
charger or used during charging.
– When the sub monitor’s signal is out of range
().
RThe sub monitor does not overcharge even if it is
continuously placed in the charger.
Battery level
RSee page 6 for a guide on operating times for the
sub monitor.
Note:
RWhen the sub monitor is off the charger or the AC
adaptor is disconnected for 1 week or more, remove
AC adaptor connections
Icon Battery level
High
Medium
Low
Needs charging
A
*1
B
WD619-OI_en.book 5 ページ ２０２０年３月１２日 木曜日 午後３時３８分

6
the batteries in order to maintain battery
performance and prevent the batteries from
discharging.
– Recharge the batteries before using the sub
monitor again.
Wall mounting
Note:
RMake sure that the wall and the fixing method are
strong enough to support the weight of the unit.
RDrive the screws (locally procured) into the wall.
Registering the product to the
Video Intercom System
The operations described here are based on the VL-
SWD275 series main monitor. See the Operating
Instructions of the Video Intercom System for more
information.
When registering the product to a main monitor of a
different series, follow the instructions in the
documentation included with your main monitor.
1 Main monitor:
Press MN→select “Register/Cancel”→
.
2 Select “Register”→.
RWhen you are prompted to register your main
monitor, select “Main monitor”→.
3 Select “Sub monitor”→.
4 Select the registration number of the sub monitor to
be registered →.
RComplete the following operations within about 2
minutes.
5 Sub monitor:
RTo register a sub monitor for the first time:
When “Please register the device.”is
displayed on the screen, select →
.
–“Registering completed”is displayed.
RTo re-register a sub monitor:
Press →select “Register”→
→.
–“Registering completed”is displayed.
6 Main monitor:
Press MN.
Cleaning
Wipe the product with a soft, dry cloth.
For excessive dirt, wipe the product with a cloth slightly
dampened with fresh water.
Cleaning the charger:
For safety, disconnect the charger from the power
supply before cleaning.
Cleaning the sub monitor:
To avoid mistakenly operating the sub monitor, remove
its batteries before cleaning.
Specifications
Main body
*1 When used fully charged in an operating
temperature of 20 °C.
*2 When the operating temperature is 20 °C. The
charging time may increase when the operating
temperature is lower than this.
*3 When registered to the main monitor.
25 mm
Power source Rechargeable battery AAA
(R03) Ni-MH battery (1.2 V,
550 mA) ×2
Dimensions
(mm) (height ×
width ×depth)
Approx. 173×52×30
(excluding protruding sections)
Mass (weight) Approx. 160 g(including the
batteries)
Operating
environment
Ambient temperature: approx.
0°C to +40 °C
Relative humidity (non-
condensing): up to 90 %
Display Approx. 5.6 cm (2.2 inches,
colour display)
Frequency
range
1.88 GHz to 1.90 GHz
RF transmission
power
Approx. 10 mW (average power
per channel)
250 mW (max.)
Talking method Hands-free
Operating time
*1
Standby use: approx. 80 hours
Charging time
*2
Approx. 8 hours
*3
Transmitting
range
Approx. 100 m (line-of-sight
distance from the main monitor)
WD619-OI_en.book 6 ページ ２０２０年３月１２日 木曜日 午後３時３８分

7
Charger
Note:
RDesign and specifications are subject to change
without notice.
RThe software of this product is based in part on the
work of the Independent JPEG Group.
RNames, company names, product names, software
names, and logos mentioned in this manual are
trademarks or registered trademarks of the
companies concerned.
Power source AC adaptor (PNLV226)
5.5 V DC, 0.5 A
Power
consumption
Standby: 0.6 W
(when the sub monitor with full-
charged batteries is placed on
the charger)
During charging: 1.6 W
Dimensions
(mm) (height ×
width ×depth)
Approx. 43×81×76
(excluding protruding sections)
Mass (weight) Approx. 70 g(excluding the AC
adaptor)
Operating
environment
Ambient temperature: approx.
0°C to +40 °C
Relative humidity (non-
condensing): up to 90 %
WD619-OI_en.book 7 ページ ２０２０年３月１２日 木曜日 午後３時３８分

WD619-OI_en.book 8 ページ ２０２０年３月１２日 木曜日 午後３時３８分