Panasonic WV-LZ62/8 User manual

Vari-Focal Lens
WV-LZ62/8
R
©1998 Matsushita Communication Industrial Co.,Ltd.
All rights reserved. Unauthorized copying and distribution
is a violation of law.
SPECIFICATIONS
Image Size: φ6 mm [4.8 (H) X 3.6 (V) mm]
Focal Length: 5 – 40 mm
Maximum Aperture Ratio: 1 : 1.6 (Wide), 1 : 1.9 (Tele)
Angular Field of View
H: 6.6° – 52°
V: 5.0° – 39.6°
Focusing Range: 1.2 m – ∞(3.9 ft - ∞)
Mount: CS-mount, 1”-32UN
Ambient Operating Temperature: –10°C – +50°C
Dimensions: 61(W) x 52(H) x 65(D) mm
2-3/8”(W) x 2-1/16”(H) x 2-9/16”(D)
Weight: 110 g (0.24 lbs.)
Dimensions and weight indicated are approximate.
Specifications are subject to change without notice.
ORDER NO.AVS9810128C1
D2

WV-LZ62/8
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE.
REFER SERVICEING TO QUALIFIED SERVICE
PERSONNEL.
This symbol warns the user that uninsuland voltage
within the unit may have sufficient magnitude to cause
electric
shock. Therefore, it is dangerous to make any kind of
contact with any inside part of this unit.
This symbol alerts the user that impotant literature concerning
the operation and maintenance of this has been included.
Therefore, it should be read carefully in order to avoid
There are special components used in this equipment which are important for safety. These parts are indicated
by the mark on the schematic diagram and the replacement parts list. It is essential that these critical
parts should be replaced with manufacturer's specified parts to prevent X-radiation, shock, fire, or other hazards.
Do not modify the original design without permission of manufacture.
IMPORTANT SAFETY NOTICE
This service information is designed for experienced repair technicians only and is not designed for use by the
general public.
It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to
service a product.
Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any
attempt to service or repair the product or products dealt with in this service information by anyone else could
result in serious injury or death.
!WARNING
M1 YWWCC329A012 Front Cap
M2 YWBCC329A109 Iris Cover
M3 YWBCC317A112 Cord Clamp
M4 YWBCC317A103 Focus Ring
M5 YWBCC329A113 Wave Washer
M6 YWBCC329A105 Zoom Ring
M7 YWBCC329A114 C Ring
M8 YWBCC329A106 Iris Assy
M9 YWBCC317A121 Lock Knob
M10 YWWCC007A005 Rear Cap
M11 YWV8QA5076AN Operating Instructions
M12 YWV9CA3904AN Packaging Assy
REF. NO. PART NO. DESCRIPTION REF. NO. PART NO. DESCRIPTION
REPLACEMENT PARTS LIST
Important Notice
1. Components identified by " !" mark have special characteristics important for safety.
When replacing any of these components, use only manufacturer's specified parts.
2. RTL : Retention Time Limited (No longer available after discontinuing product).
MISCELLANEOUS ACCESSORY PARTS / PAKAGING PARTS

WV-LZ62/8
INSTALLATION
1. Set the ALC selector on the camera to DC position.
3. Connect the lens cable to the Auto Iris Lens Connector on the
side of the camera.
ADJUSTMENT
1. Loosen the Focus Lock Screw by turning it counterclockwise,
and then set this screw to the “F” position.
ALC
DC VIDEO
ELC
ELC
DC
ALC
VIDEO
(Fig. 1)
2. Mount the lens by turning it clockwise on the lens mount of the
camera.
8X TV LENS
5 ~ 40 mm 1:1.6
WV-LZ62/8
T
W
F
N
13
(Fig. 3)
Focus lock screw
Zoom ring
(Fig. 2)
2. Turn the Zoom Ring toward “W” until it stops.
8X
T
W
F
N
13
TV LENS
5 ~ 40 mm 1:1.6
WV-LZ62/8
(Fig. 4)
3. Shoot an object more than 10 meters (30 feet) away to adjust
the flange-back of the camera.
4. Loosen the screws on the flange-back adjusting ring of the cam-
era, then turn this ring to bring the object into focus.
Focus adjustment
for C-mount lens
Focus adjustment
for CS-mount lens
Caution: Do not turn this ring too far counterclockwise as this
could damage the inner glass and CCD image sensor.
5. Tighten the screws on the flange-back adjusting ring.
6. Turn the Zoom Ring to a point between “T” and “W” to chose
the desired angular field of view.
7. Bring the desired object into focus by setting the Focus Lock
Screw.
8. Tighten the Focus Lock Screw by turning it clockwise.
Turn
(Fig. 5)

Printed in Japan
P-778 F 5,7
EXPLODED VIEW
M1
M2
M3
M4
M5
M6
M7
M8
M10
M11
M12
M12
WV-LZ62/8
PACKAGING
1
1
1
M9
NOT. SUPPLY
○Number's show Screws.
No. Screws Description
1 YFDA170301FN Special Screws