Panasonic H-H025PP User manual

© Panasonic Corporation 2015 Unauthorized copy-
ing and distribution is a violation of law.
ORDER NO. DSC1510023CE
B26
Interchangeable Lens for Digital Camera
Model No. H-H025PP
H-H025E
H-H025GK
Coulor
(K)..........Black Type
(S)..........Silver Type
TABLE OF CONTENTS
PAGE PAGE
1 Safety Precautions----------------------------------------------- 2
1.1. Information for Your Safety------------------------------ 2
1.2. Cautions for use ------------------------------------------- 3
2 Service Navigation ----------------------------------------------- 4
2.1. Introduction-------------------------------------------------- 4
2.2. Important Notice ------------------------------------------- 4
3 Specifications ----------------------------------------------------- 5
3.1. Specifications (Rated) ------------------------------------ 5
3.2. Accessories ------------------------------------------------- 5
4 Location of Controls and Components ------------------- 6
5 Service Fixture & Tools----------------------------------------- 7
5.1. Service Fixture and Tools-------------------------------- 7
5.2. Clean Box --------------------------------------------------- 7
6 Disassembly and Assembly Instructions ---------------- 8
6.1. Outline-------------------------------------------------------- 8
6.2. Disassembly Flow Chart --------------------------------- 8
6.3. Disassembly procedure ---------------------------------- 9
6.4. Assembly Flow Chart ------------------------------------11
6.5. Assembly procedure -------------------------------------12
7 Maintenance-------------------------------------------------------15
7.1. ABOUT THE LENS -------------------------------------- 15
8 Exploded View and Replacement Parts List ----------- 16

2
1 Safety Precautions
1.1. Information for Your Safety

3
1.2. Cautions for use

4
2 Service Navigation
2.1. Introduction
This service manual contains technical information, which allow service personnel’s to understand and service this model
Please place orders using the parts list and not the drawing reference numbers.
If the circuit is changed or modified, the information will be followed by supplement service manual.
2.2. Important Notice
2.2.1. About LENS MAIN UNIT (Ref. 209)
1. LENS MAIN UNIT (Ref. 209) is not supplied due to difficulty of the transportation issue (Fragile, Dust-free packing), and
requires critical lens adjustments.
Therefore, any needs of the "LENS MAIN UNIT" (Ref. 209), carefully confirm its performance in advance.
2. Once "LENS MAIN UNIT" (Ref. 209) is confirmed as defective, place order "LENS Unit" (Ref. 200) and replace SHADING
FRAME (Ref. 208), to maintain Serial number of owner's original lens.
Fig. 1-1
3. No adjustment is required when replacing the part mentioned on Fig.1-1. But, when tighten the concerned screws,apply
proper torque mentioned on "4. Disassembly and Assembly Instruction" section.

5
3 Specifications
3.1. Specifications (Rated)
3.2. Accessories

6
4 Location of Controls and Components

7
5 Service Fixture & Tools
5.1. Service Fixture and Tools
The following Service Fixture and Tools are used for Checking & Servicing for this unit.
5.2. Clean Box
• The repair quality is considered, and it is recommended working in the environment of satisfied clean level less than class
10,000 (Federal Standard 209D).
[NOTE]
• Work in the environment of satisfied clean level less than class 10,000 (Federal Standard 209D) for cleaning the inside of the
lens.

8
6 Disassembly and Assembly Instructions
6.1. Outline
Please be disassembly and assembly with reference to the flow chart and illustrations drawings.
Important:
1. It is recommended dealing with Clean Box, to keep maintaining the dustproof environment.
(Refef to " 5.2. Clean Box " section of this Service Manual for details.)
2. To minimize the possibilities/risk of getting the dust/dirt on the lens surface, keep covering the lens unit with lens caps (front &
rear), other than necessary cases.
3. Do not touch the surface of the lens glasses with your fingers.
4. Blow off the dust on the surface of the lens with a blower brush.
5. Use lens cleaning KIT (BK)(VFK1900BK).
NOTE:
1. When installing the screws, be sure to use the torque driver (RFKZ0456) and tighten the screws with specified torque, men-
tioned on the following.
6.2. Disassembly Flow Chart
Caution
Keep covering the lens unit with Lens caps (front & rear), other than necessary cases.

9
6.3. Disassembly procedure
6.3.1. Removal of the Deco. Ring Unit
1. Deco. Ring Unit is sticked on the Filter Ring.
2. Put the sheet so that the lens glass is fullty covered.
3. Insert the small flat blade screwdriver to Gap (between
the Deco. Ring Unit and lens glass), and peel off the
Deco. Ring Unit gently.
6.3.2. Removal of the Dust Proof Ring
and the Filter Ring
1. Remove the Dust Proof Ring.
2. Remove 3 screws (A) and the Filter Ring.
6.3.3. Removal of the Shading Frame
1. Remove 2 screws (B) and the Shading Frame.
6.3.4. Removal of the L Mount Unit
1. Remove 1 screw (C) and 3 screws (D).
2. Remove the L Mount Unit.

10
6.3.5. Removal of the Lens P.C.B. Unit
and the Lens Mount Contact Unit
1. Remove 2 screws (E) and disconnect 5 connectors.
2. Remove the Lens P.C.B. Unit and the Lens Mount Con-
nect Unit.
3. Disconnect a connector of the Lens P.C.B. Unit and
remove the Lens Mount Connect Unit.
6.3.6. Removal of the Rear Frame Unit
1. Remove 3 screws (F) and the Rear Frame Unit.

11
6.4. Assembly Flow Chart

12
6.5. Assembly procedure
Important:
1. When tightening the screw, use a torque driver
(RFKZ0456) by ordering the screwing order with specified
torque described in each step.
2. Mounting that the Filter Ring and the Rear Frame Unit as
Lens fitting mark are aligned.
6.5.1. Installation of the Filter Ring Unit
and the Dust Proof Ring
1. Mounting that the Filter Ring as Lens fitting mark are
aligned.
2. Tighten 3 screws (A) by using the torque driver with spec-
ified torque.
3. Install the Dust Prooof Ring.
6.5.2. Installation of the Deco. Ring Unit
1. Please insert the 3 protrusions of the Deco. Ring Unit
back to 3 holes of the Filter Ring.
(Caution)
• Use new one, do not use the one which is removed.
• Please remove the old double-stick tape from the Lens
Unit.
2. After installing the Deco. Ring Unit use a soft cloth to
Press it into place.

13
6.5.3. Installation of the Rear Frame Unit
1. Install the Rear Frame Unit.
2. Tighten 3 screws (F) by using the torque driver with spec-
ified torque.
6.5.4. Installation of the Lens P.C.B. Unit
and the Lens Mount Contact Unit
1. Connect FPC of the Lens Mount Connect Unit to connec-
tor.
2. Installation the Lens P.C.B. Unit with the Lens Mount
Connect Unit.
3. Connect FPCs to 2 connectors of the Lens P.C.B. Unit.
4. Tighten 2 screws (E) by using the torque driver with spec-
ified torque.

14
6.5.5. Installation of the L Mount Unit
1. Install the L Mount Unit.
2. Tighten 1 screw (C) and 3 screws (D) in numerical order
by using the torque driver with specified torque.
6.5.6. Installation of the Shading Frame
1. Install the Shading Frame.
2. Tighten 2 screws (B) in numerical order by using the
torque driver with specified torque.

15
7 Maintenance
7.1. ABOUT THE LENS
7.1.1. DUST/DIRT ON THE OUTER CASING PART(S)
1. Blow off the dust first, then sweep out the dust from narrower spaces with soft cleaning brush.
2. Wipe up the Outer casing part with the dry fuzz-free cloth.
7.1.2. DUST/DIRT ON THE LENS GLASSES
Define the location of the dust/dirt first, whether it is outside
lens surface or not.
1. When it is outside surface of the lens:
When the dust and/or dirt gets on the outer side surface
of the Lens glasses, order the following procedures.
a. Blow off the dust on the Lens glass surface with the
Blower, gently. (Do not Blow too strongly.)
b. Wipe out the dirt on the lens glass surface with Lens
cleaning KIT (VFK1900BK) if necessary.
(Consult the Instruction sheet which is included in the
Lens cleaning KIT in details.)

16
8 Exploded View and Replacement Parts List
Please click the radio button for "Diagrams II / Parts List" on the menu bar in XML Service Manual.
If you want to print, please click the icon button for "Print" on the icon bar and select the item.