Panasonic ET-D75LE95 User manual

ENGLISH
FRANÇAIS
Model No. ET-D75LE95
DPQX1086ZB
Fixed-focus Lens
Operating Instructions
Thank you for purchasing this Panasonic product.
■To ensure correct use of this lens, please read the operating instructions supplied with the lens and the
projector carefully.
■Before using this product, be sure to read “Read this rst!” (Page 3).
■Please save this manual for future use.
Commercial Use

2-ENGLISH
Read this rst! ......................................................................................3
Before Use.............................................................................................4
Attaching the Lens / Detaching the Lens...........................................4
Before replacing the projection lens........................................................4
Attaching the Lens...................................................................................5
Detaching the Lens .................................................................................6
Projection relationships.......................................................................7
Lens position setup and focus adjustment .......................................9
Lens position setup .................................................................................9
Focus Adjustment Function................................................................... 11
Adjustment range by the lens position shift (optical shift)............12
Specications .....................................................................................14
Dimensions .........................................................................................14
Dimensional relationship...................................................... Appendix
█ Contents

ENGLISH-3
Read this rst! Always follow these precautions
WARNING:
Before replacing the projection lens, be sure to turn off the power and
disconnect the power plug from the wall outlet.
zUnexpected projection of light may cause injury to eyes.
zReplacing without removing the power plug may result in electrical shock.
Do not place objects near the light projecting surface.
zThis surface produces intense light. Failure to heed this warning could result in re
or burn injuries.
CAUTION:
Do not use the lens with the protective lm and lens cover left on.
zIf left on, the heat generated during projection could melt them resulting in projector
deformation and damage, and personnel attempting to remove them could suffer
burn injuries.
Do not open the desiccant bag. Do not eat the contents.
Inadvertently ingesting desiccant could be harmful.
zIf the desiccant gets into your eyes or mouth, immediately rinse with plenty of water
and seek medical attention.
zKeep desiccant out of the reach of children.
Note
zThis product cannot be used if an optional frame (ET-PFD510 / ET-PFD310) is attached and used with the projector.
Information for users in the European Union
Importer’s name and address within the European Union
Panasonic Marketing Europe GmbH
Panasonic Testing Centre
Winsbergring 15, 22525 Hamburg, Germany

4-ENGLISH
Before replacing the projection lens
Return the projection lens to the home position before replacing or removing it.
For details on how to return the lens to the home position, refer to the operating instructions of the projector.
Attention
zMake sure that the projector power supply is switched off before attaching or detaching the projection lens.
zAfter removing the projection lens, store it safely away from vibration or impacts.
zBefore attaching the xed-focus lens, remove the protective lm from the light projecting surface and the lens
cover from the lens.
zBe sure not to touch the light projecting surface or the surface of the lens. Any ngerprints or smudges on
these surfaces will be magnied and lower the quality of the image displayed on the screen.
zThe light projecting surface and lens are made of glass. The lens could be damaged if brought into contact
with or rubbed against hard objects. Handle the lens carefully.
zUse a clean, soft and dry cloth to wipe away any dirt or dust that has adhered to the light projecting surface or lens.
Do not use uffy cloths containing oil, water or dust for cleaning.
zWhen the xed-focus lens is removed from the projector, place it with the light projecting surface facing
upwards.
Attaching the Lens / Detaching the Lens
Before Use
 Supported projectors
PT-RZ31K / PT-RS30K / PT-RQ13K / PT-RZ12K / PT-RS11K / PT-DZ21K2 / PT-DS20K2 / PT-DW17K2 /
PT-DZ16K2 / PT-DZ13K / PT-DS12K / PT-DW11K / PT-DZ10K
Note
zModels other than the above may also be supported. Refer to the operating instructions of the projector you are using.
zIn this document, the alphabet letters at the end of the projector part numbers are omitted.
 Supplied Accessories
Make sure that the following has been provided. Numbers enclosed in < > show the number of accessories.
Lens cover <1>
(The product is delivered with a lens cover attached.)
Lens surface Light projecting surface
Lens cover
Protective lm

ENGLISH-5
The illustration for this procedure uses PT-DZ21K2
as an example.
1) Remove the projection lens cover.*1
2) Align the mark on the projection
lens (orange color) with the mark
on the projector (O on the left
side of the LOCK) and insert; then
rotate in a clockwise direction
until it makes a "click" sound.
3) Secure the projection lens with
the lens drop prevention screw
included with the projector.
zSecure it in the screw hole (location shown in
the gure to the left) on the right side of the
projection lens mark (orange color) using a
Phillips screwdriver.
4) Attach the projection lens cover.*1
Attention
zGently turn the projection lens counterclockwise
to check that it will not fall out.
Attaching the Lens
Attaching the Lens / Detaching the Lens (continued)
Projection
lens cover
(i)
(i)
(i)
(i)
(ii)
Orange color
(i)
(ii)
Lens drop
prevention
screw
*1:Only when using a projector that has a projection lens cover. In addition, there are cases where the attachment method
or removal method of the projection lens cover differs from the procedure (illustration) described above depending on the
model being used. For details, see "Attaching/removing the projection lens (optional)”
in the operating instructions for
the projector you are using.

6-ENGLISH
The illustration for this procedure uses PT-DZ21K2
as an example.
1) Remove the projection lens cover.*1
2) Remove the lens drop prevention
screw.
zRemove the rst screw on the right side of the
projection lens mark (orange color) using a
Phillips screwdriver.
3) Turn the projection lens
counterclockwise while holding
down the lens release button to
take it off.
zTurn counterclockwise until the projection lens
mark (orange color) is aligned with the mark
on the projector (O on left side of the LOCK).
4) Attach the projection lens cover.*1
Attention
zStore the projection lens that was removed while
avoiding vibration and impact.
zStore the lens drop prevention screw that was
removed and do not lose it.
zAttach the supplied lens cover before storing the
lens.
Projection
lens cover
(i)
(i)
(i)
(i)
(ii)
Lens
release
button
Orange color
(iii)
(i)
(ii)
Detaching the Lens
*1:Only when using a projector that has a projection lens cover. In addition, there are cases where the attachment method
or removal method of the projection lens cover differs from the procedure (illustration) described above depending on the
model being used. For details, see "Attaching/removing the projection lens (optional)”
in the operating instructions for
the projector you are using.
Attaching the Lens / Detaching the Lens (continued)

ENGLISH-7
The dimensional relationship between the screen and the projector is shown below.
 Dimensional relationship diagram
SH
SW
SD
SH
A1
L3
L4
A2
L1
L2
Projected image
Screen
Note
zThe indications of this illustration are premised on aligning the projected image size and position to the full screen.
zThis illustration is not drawn to scale.
SH Projected image height L3 Screen to projector front end
SW Projected image width L4 Screen to projector rear end
SD Diagonal length of the projected image A1 Bottom edge of the screen to the top of the
projector
L1 Projection distance
(from screen to mirror reective surface*) A2 Bottom edge of the screen to the bottom of the
projector
L2 Screen to lens front end
* The mirror reective surface is inside the xed-focus lens, and is not visible from the outside.
Note
zThe illustrations of projectors in this manual are for informational purposes only and do not represent a specic
projector model. Congurations may vary with the model.
zAfter setting the lens position using the function on the projector, the lens position can be adjusted within the
adjustment range described in "Adjustment range by the lens position shift (optical shift)" (Page 12).
Then dimensions A1 and A2 will change according to lens shift amount.
zDimension L4 is the distance from the projector rear panel to the screen.
zDimension A2 is the distance from the bottom edge of the screen to the bottom of the adjustable projector legs
(with the legs fully screwed in).
Attention
zDimension L4 is not the distance from the projector rear panel to a wall, but the distance from the projector
rear panel to the screen. Provide at least 500 mm (19-11/16") of ventilation space between the projector rear
panel and a wall or other object.
When placing the projector in a conned space, a ventilation and/or air conditioning system is required.
Exhaust heat may accumulate when the ventilation is not sufcient triggering the protection circuit of the projector.
Projection relationships

8-ENGLISH
 Keystone distortion correction
When attaching this lens for use, regardless of the projector model, set up the projector so that the projected
image is rectangular and the back of the projector and the screen are parallel.
In addition, depending on the projector used, keystone distortion correction may be feasible after setup.
zWhen using one of PT-RZ31K / PT-RS30K / PT-RQ13K / PT-RZ12K / PT-RS11K / PT-DZ21K2 /
PT-DS20K2 / PT-DW17K2 / PT-DZ16K2 / PT-DZ13K / PT-DS12K / PT-DZ10K
For keystone distortion in the vertical direction generated within the angle range below, select [MAIN MENU] →
[POSITION] →[GEOMETRY] →[KEYSTONE] →[VERTICAL KEYSTONE] to perform correction.
Keystone distortion in the vertical direction greater than this angle and keystone distortion in the horizontal
direction can be corrected but the projected image overall will no longer be in focus.
Correction feasible angle (α): 0 - 5°
zWhen using PT-DW11K
If keystone distortion in vertical direction or horizontal direction is corrected, the projected image overall will no
longer be in focus. Set up the projector so that the projected image is rectangular and the back of the projector
and the screen are parallel.
zWhen using a projector other than one listed above
Please see "Setting up" in the operating instructions for the projector you are using.
Projection relationships (continued)
 Dimensional relationship
zWhen using one of PT-RZ31K / PT-RS30K / PT-RQ13K / PT-RZ12K / PT-RS11K / PT-DZ21K2 /
PT-DS20K2 / PT-DW17K2 / PT-DZ16K2 / PT-DZ13K / PT-DS12K / PT-DW11K / PT-DZ10K
For details on projection distance (L1), and A1, A2, L2, L3 and L4 values, refer to "Projected image size and
Projection distance" or "Projection distance formulas" in the Appendix.
zWhen using a projector other than one listed above
Please see "Setting up" in the operating instructions for the projector you are using.
Screen
(Side view)
α

ENGLISH-9
Lens position setup
Automatically return the lens to standard position using the projector.
The menu screens shown in these operating instructions are only provided as examples. Actual menu screens
may vary with the specic model.
● When using PT-RZ31K / PT-RS30K / PT-RQ13K / PT-RZ12K / PT-RS11K / PT-DZ21K2 / PT-DS20K2 /
PT-DW17K2 / PT-DZ16K2
Lens position setup and focus adjustment
1) Turn on the projector, and start
projection.
2) Press the <DEF
AULT> button on
the remote control while the shift
adjustment screen is displayed.
zThe [HOME POSITION] screen is displayed.
3) Press ◀▶ to switch the item.
zThe items will switch each time you press the button.
[NORMAL]
Moves the lens to the home position.
Select this item when replacing or removing
the projection lens. Select this item
when the Fixed-focus Lens (Model No.:
ET-D75LE50) is used for projection.
[D75LE95]
or
[D75LE90]*1
Moves the lens to the ET-D75LE95 lens
standard position.
Select this item when the Fixed-focus
Lens (Model No.: ET-D75LE95) is used for
projection.
*1: The items displayed will differ depending on the projector
model.
4) Press the <ENTER> button.
z[PROGRESS] is displayed in the [HOME POSITION]
screen, and the lens position returns to the home
position or the lens standard position.
LENS
HOME POSITION
EXECUTE CANCEL
ENTER
MENU
NORMAL
CHANGE
Note
zComplete the operation within approximately 5 seconds after the [HOME POSITION] screen is displayed. The
[HOME POSITION] screen will disappear after time limit.
zThe home position of the lens is used when the lens is being replaced or when the projector is being stored,
and it is not the optical center of the screen.
zYou can also display the [HOME POSITION] screen by pressing the <LENS> button on the control panel or
the <SHIFT> button on the remote control for at least three seconds.

10-ENGLISH
1) Turn on the projector to start the
projection.
2) Press the <MENU> button to open
the [MAIN MENU] screen. Then select
[PROJECTOR SETUP] and press the
<ENTER> button.
3) Select [SERVICE PASSWORD] in the
[PROJECTOR SETUP] menu and press
the <ENTER> button.
4) In the [SERVICE PASSWORD] entry
screen, enter "7590" using the numeric
buttons on the remote control and then
press the <ENTER> button.
zThe [D75LE90 POSITION] screen appears.
5) Press the <ENTER> button in the [D75LE90
POSITION] screen.
z[PROGRESS] is displayed on the [D75LE90 POSITION]
screen and lens position moves to the standard position
for the ET-D75LE95.
Note
zWhen using the PT-DZ13K / PT-DS12K / PT-DW11K /
PT-DZ10K, the [MAIN VERSION] of the projector rmware
must be the version described below. Check the [MAIN
VERSION] of the rmware on the [STATUS] screen and
upgrade the rmware version of the projector as needed. *1
Projector Main version
PT-DZ13K / PT-DS12K /
PT-DW11K / PT-DZ10K 4.04 or higher
[STATUS] screen is displayed by selecting [Main Menu]
→[PROJECTOR SETUP] →[STATUS] or by pressing the
<STATUS> button on the remote control.
DZ13K
*1: See software download page on Panasonic website (https://panasonic.net/cns/projector/pass/). You must be a
registered PASS user to use the site described above.
PASS: Panasonic Professional Display and Projector Technical Support Website
Lens position setup and focus adjustment (continued)
Note
zThe lens position set here may not match the intended standard position exactly.
zThe lens position set with this procedure will be used as the standard position. The lens position can be
adjusted within the adjustment range described in "Adjustment range by the lens position shift (optical shift)"
(

Page 12), even after shifting to the standard position.
zDepending on the (OSD) display position on the menu screen, there are cases where the projected light is
obstructed and a part of the menu is not displayed on the screen. In this case, open [MAIN MENU] →[DISPLAY
OPTIONS] →[ON-SCREEN DISPLAY] →[OSD POSITION] and change settings so that the whole OSD menu
can be seen.
● When using PT-DZ13K / PT-DS12K / PT-DW11K / PT-DZ10K