Panasonic KX-TDA15 User manual

Model No. KX-TDA15
Thank you for purchasing a Panasonic Hybrid IP-PBX.
Please read this manual carefully before using this product and save this manual for future use.
PSMPR Software File Version 4.0000 or later
Hybrid IP-PBX
Getting Started

2 Getting Started
Table of Contents
1 Before Installation .................................................................................. 3
1.1 System Connection Diagram ...........................................................................................4
1.2 Unpacking..........................................................................................................................5
2 Installation............................................................................................... 7
2.1 Opening/Closing the Covers ............................................................................................8
2.2 Installing the SD Memory Card ......................................................................................10
2.3 Installing the Optional Service Cards ...........................................................................10
2.4 Installing the Trunk Cards ..............................................................................................13
2.5 Installing the Extension Cards (DLC8/SLC8)................................................................14
2.6 Connecting Extensions ..................................................................................................15
2.7 Frame Earth Connection ................................................................................................15
3 Starting the Hybrid IP-PBX .................................................................. 17
3.1 Starting the Hybrid IP-PBX.............................................................................................18
4 Customising the Hybrid IP-PBX .......................................................... 21
4.1 Connecting the PC..........................................................................................................22
4.2 Installing the KX-TDA30 Maintenance Console ...........................................................23
4.3 Programming the Hybrid IP-PBX ...................................................................................23
5 Confirming the Connection ................................................................. 29
5.1 Making Calls ....................................................................................................................30

Getting Started 3
Section 1
Before Installation

1.1 System Connection Diagram
4 Getting Started
1.1 System Connection Diagram
*1The Hybrid IP-PBX has 4 Super Hybrid Ports, one BRI2 card, and one EXT-CID card pre-installed.
*2ITSP: Internet Telephony Service Provider
Radio
Amplifier Pager/Speaker
CTI Server
Station Message
Detail Recording (SMDR)
PC
SLT Fax Machine
for Single Line Device
SLC8
(KX-TDA3174)
ECHO8
(KX-TDA3166)
EXT-CID
*
1
Telephone
Company
Hybrid IP-PBX
4 Super Hybrid Ports
*
1
Main Board
Analogue
Trunk
BRI2
*
1
(KX-TDA3280)
BRI1
(KX-TDA3283)
LCOT2
(KX-TDA3183)
ISDN BRI Line
ISDN BRI Line
(Digital Trunk)
(Digital Trunk)
ISDN BRI Line
(Digital Trunk)
DPH4
(KX-TDA3161)
DPH2
(KX-TDA3162)
Doorphone & Door Opener
External Sensor/
External Relay Device
MSG2
(KX-TDA3191)
SVM2
(KX-TDA3192)
SLT Wireless
Phone
DPT DSS
Console
Voice
Processing
System
PT-interface CS PS
for Single Line Device,
DPT/Analogue
Proprietary Telephone
(APT), DSS Console,
and PS
PC
KX-T7636/
KX-T7633
APT
PCKX-T7636/
KX-T7633
DSS
Console
DPT
Voice
Processing
SystemPT-interface CS PS
for Digital Proprietary
Telephone (DPT),
DSS Console, and
Portable Station (PS)
DLC8
(KX-TDA3172)
IP-EXT4
(KX-TDA3470)
LAN
IP-PT IP Softphone
Private
IP Network
Router
IP-GW4
(KX-TDA3480)
PC
LAN
CTI Server
KX-T7600
DPT KX-T7600 DPT
SIP-DSP4
(KX-TDA3451)
SIP-GW4
(KX-TDA3450)
PC
LAN
ITSP
*
2
Network
ADSL
Modem
WAN

1.2 Unpacking
Getting Started 5
Note
In this manual, the suffix of each model number (e.g., KX-TDA15NE) is omitted unless
necessary.
1.2 Unpacking
Check the package contents.
Main Unit × 1
CD-ROM (including manuals, etc.) × 1
AC Cord* × 1 AC Adaptor × 1 Screw × 5
Washer × 5 Mini Plug (for pager and music
source) × 2
SD Memory Card × 1
Main Strap × 1 Strap (for the pre-installed
BRI2 card) × 1
Optional Card Label Sheet × 1
* The type of the AC cord may vary depending on the country/area of use.

1.2 Unpacking
6 Getting Started
Necessary tools (not supplied):
Telephone cable for extension connection:
The maximum length of the cable may vary depending on the type of the cables and installation
conditions.
An RS-232C or USB cable for PC connection
Connectors (RJ45/RJ11)* for trunk and extension connections
Note
Use a twisted pair cable for the RJ45 or RJ11 connector.
Diameter of cable
(ø 0.4 mm to ø 0.6 mm)
Maximum length of cable
ø 0.5 mm 1128 m for SLT
ø 0.5 mm 720 m for KX-T7600 series
ø 0.5 mm 229 m for other DPT, APT and DSS Console
* The connector type may be RJ45 or RJ11 depending on the country/area.

Getting Started 7
Section 2
Installation

2.1 Opening/Closing the Covers
8 Getting Started
2.1 Opening/Closing the Covers
Opening the Covers
1. Pull the slide button to the right and, holding it, slide the cable cover upwards. Then turn the cable
cover slightly to remove it.
2. Remove the three screws.
3. Holding the protrusions on both sides of the front cover, swing the cover open.
Slide Button
Cable Cover
Screw

2.1 Opening/Closing the Covers
Getting Started 9
Closing the Covers
1. Close the front cover, then tighten the three screws.
2. Attach the rear hooks on the cable cover to the main unit, then swing the cable cover closed so
that the front hooks fit in place.
3. Slide the cable cover down until it locks.
Screw
Cable Cover

2.2 Installing the SD Memory Card
10 Getting Started
2.2 Installing the SD Memory Card
The SD Memory Card contains software for all the processes of the Hybrid IP-PBX and all the
customer data. The SD Memory Card must be inserted before startup.
CAUTION
Do not remove the SD Memory Card while power is supplied to the Hybrid IP-PBX. Doing so may
cause the Hybrid IP-PBX to fail to start when you try to restart the system.
2.3 Installing the Optional Service Cards
Slot Position
*1Slots 10 and 11 accept only cards which do not have external ports. Therefore, these slots do
not have removable cover plates.
*2Slot 08 contains the pre-installed EXT-CID card.
*3Slot 02 contains the pre-installed BRI2 card.
*4Slot 01 contains the pre-installed Super Hybrid Ports. No optional service card can be installed.
SD Memory Card
Slot Cover
SD Memory
Card
02*3
03
04
05
06
07
08*2
09
10*1
11*1
01*4

2.3 Installing the Optional Service Cards
Getting Started 11
Slot Restrictions
The following table shows the slot restrictions. " " indicates that the slot supports the optional
service card.
Trunk Card Combinations
Trunk cards can be installed along with the pre-installed BRI2 card in any one of the following
combinations:
•BRI2+BRI2
•BRI2+BRI1
• BRI2 + LCOT2
• BRI2 + BRI1 + LCOT2
CAUTION
To protect the main board from static electricity, do not touch parts on the main board or on the
optional service cards. To discharge static electricity, touch ground or wear an earthing strap.
Card Slot Number
Type Max 0304050607091011
LCOT2 1
BRI2 1
BRI1 1
SIP-GW4 1
2IP-GW4 1
IP-EXT4 1
DLC8
1*1
*1 Only one of either the DLC8 or SLC8 card can be installed.
SLC8
DPH4
1*2
*2 Only one of either the DPH4 or DPH2 card can be installed.
DPH2
ECHO8 1
MSG2 2
SVM2 2

2.3 Installing the Optional Service Cards
12 Getting Started
Installing the Trunk/Extension Cards
1. Before installing the optional service cards, cut and remove the appropriate dummy cover plates
from the main unit.
CAUTION
For safety reasons, smooth the cut edges after removing the dummy cover plates.
2. Position the card in the open slot, making sure that the tabs on the both sides of the card fit into
place. Then, holding the card firmly in place, lower the rear end so that the hole of the card fits
over the extension bolt.
CAUTION
When installing the optional service cards, do not put pressure on any parts of the main board.
Doing so may result in damage to the Hybrid IP-PBX.
Dummy Cover Plate
1
2
Extension Bolt
Optional Service Card

2.4 Installing the Trunk Cards
Getting Started 13
3. Insert the new extension bolt (included with the card) into the hole on the card, and tighten it to
secure the card.
2.4 Installing the Trunk Cards
LCOT2 Card
Accessories (included): Extension Bolt × 1, Strap × 1, Optional Card Label × 1
User-supplied (not included): RJ45 connector
Extension Bolt
To trunk
RJ45

2.5 Installing the Extension Cards (DLC8/SLC8)
14 Getting Started
BRI1/BRI2 Card
Accessories (included): Extension Bolt × 1, Strap × 1, Optional Card Label × 1 (for BRI1 card)
User-supplied (not included): RJ45 connector
Notes
• Connect these optional service cards to the trunk through an NT1; do not connect to the U
interface of the trunk directly.
• These optional service cards have 100 Ωof terminal resistance. For use in point to multi-
point connection, the cards must be placed at the end of the bus.
2.5 Installing the Extension Cards (DLC8/SLC8)
Accessories (included): Extension Bolt × 1, Strap × 1
User-supplied (not included): RJ45 connector or RJ11 connector*
* The connector type may be RJ45 or RJ11 depending on the country/area.
To N T 1
RJ45 (LINE 1)
RJ45 (LINE 2)
Example: BRI2 Card
To extension
RJ45
Example: DLC8 Card

2.6 Connecting Extensions
Getting Started 15
2.6 Connecting Extensions
2.7 Frame Earth Connection
IMPORTANT
Connect the frame of the Hybrid IP-PBX to earth.
• Proper earthing (connection to earth) is very important to protect the Hybrid IP-PBX from the bad
effects of external noise or to reduce the risk to the user of electrocution in the case of a lightning
strike.
• The earthing wire of the AC cable has an effect against external noise and lightning strikes, but
it may not be enough to protect the Hybrid IP-PBX. A permanent connection between earth and
the earth terminal of the Hybrid IP-PBX must be made.
1. Loosen the screw.
2. Insert an earthing wire (user-supplied)*.
3. Tighten the screw.
4. Connect the earthing wire to earth.
* For earthing wire, green-and-yellow insulation is required, and the cross-sectional area of the
conductor must be more than 0.75 mm2or 18 AWG.
To extension card
RJ11
Example: KX-T7600 Series DPT
DPT and DSS Console
KX-T7000 Series SLT
Pin Assignments
H L
T R
APT
HTRL
TO MAIN UNIT
/ PABX
H L
Screw
Earthing
wire
To earth

2.7 Frame Earth Connection
16 Getting Started

Getting Started 17
Section 3
Starting the Hybrid IP-PBX

3.1 Starting the Hybrid IP-PBX
18 Getting Started
3.1 Starting the Hybrid IP-PBX
CAUTION
• The SD Memory Card must be inserted in the SD Memory Card slot of the main board
before startup.
• Before touching the System Initialise Switch, discharge static by touching ground or wearing
an earthing strap.
• Once you have started the Hybrid IP-PBX and if you unplug the Hybrid IP-PBX, do not
perform the following procedures to start the Hybrid IP-PBX again. Otherwise, your
programmed data will be cleared.
• The Hybrid IP-PBX will continue to be powered even if the power switch is turned "OFF".
•The power supply cord is used as the main disconnect device. Ensure that the AC
outlet is located near the equipment and is easily accessible.
1. Slide the System Initialise Switch to the "SYSTEM INITIALIZE" position.
2. Plug the DC connector of the AC adaptor into DC IN 1.
System Initialise Switch
RUN Indicator
ALARM Indicator
AC Adaptor
DC Connector
DC IN 1
2
1

3.1 Starting the Hybrid IP-PBX
Getting Started 19
3. Plug the AC cord into the AC adaptor, and then plug the other end into an AC outlet.
4. Turn on the power switch. The RUN indicator will flash.
Notes
• For safety reasons, follow the procedures as indicated when turning on the Hybrid IP-PBX.
• For safety reasons, do not stretch, bend, or pinch the AC cord and the DC cable of the AC
adaptor.
5. While the RUN indicator is flashing, slide the System Initialise Switch back to the "NORMAL"
position. Depending on the configuration, initialisation takes about 1 min to 3 min. If successfully
executed, the RUN indicator will stop flashing and stay lit.
All data will be cleared and the Hybrid IP-PBX will be initialised to the default values. The DPTs should
show the time as 01:00.
IMPORTANT
Use only the AC adaptor (Panasonic PSLP1244/Panasonic PSLP1434) and AC cord
supplied with the Hybrid IP-PBX.
AC Adaptor
AC Cord
To AC outlet
Power Switch

3.1 Starting the Hybrid IP-PBX
20 Getting Started