Panasonic ET-LAD310A User manual

Thank you for purchasing this Panasonic product.
■Please read these operating instructions and the projector operating instructions carefully, and then use
this product correctly.
■Page 2).
■Please save this manual for future use.
Model No. ET-LAD310A (1 pc)
ET-LAD310AW (2 pcs)
ET-LAD320P (1 pc)
ET-LAD320PW (2 pcs)
TQZJ496-1
Replacement lamp unit
Operating Instructions
* Model numbers ET-LAD320P and ET-LAD320PW are replacement lamp units to be used exclusively in
portrait mode.
This lamp is used in projectors.
It is not intended to be used for indoor lighting of ordinary homes.
2009 / 125 / EC
Product information (for Turkey only)
EEE Yönetmeliğine Uygundur.
EEE Complies with Directive of Turkey.
ET-LAD310A(W)_320P(W).indd 1 2013/03/22 11:15:15

2-ENGLISH
Read this rst! Always follow these precautions
WARNING:
Before replacing the lamp unit, be sure to turn the power off and to disconnect the power plug from
the wall outlet.
zElectric shocks or explosions can result if this is not done.
Do not disassemble the lamp unit.
zIf the lamp breaks, it could cause injury.
Do not remove unspecied screws during the lamp unit replacement.
zDoing so can cause electric shocks, burns, or injury.
When replacing the lamp unit, turn the power off and allow the lamp to cool for at least one hour
before handling it.
zThe cover reaches a very high temperature, so failure to observe this will cause burns.
CAUTION:
Do not touch the fan with your ngers or any other parts of your body when replacing the lamp unit.
zDoing so can cause injury.
NOTICE
For USA only
Hg-LAMP CONTAINS MERCURY, Manage in Accord with Disposal Laws.
See: www.lamprecycle.org or 1-888-411-1996
ET-LAD310A(W)_320P(W).indd 2 2013/03/22 11:15:15

ENGLISH-3
Before replacing the lamp unit

Make sure to turn off the power before replacing the
lamp unit.
When switching off the projector, make sure
to follow the procedures in “Switching off the
projector” (page 3).
■
Checking the lamp unit to be
replaced
Check the status of the lamp
indicators <LAMP1>/<LAMP2>.
The lamp unit corresponding to the lamp indicator
that is lit in red is required to be replaced.
Main unit operating part
＜
Power indicator
＞
（ON (G) / STANDBY (R) ）
<Lamp indicator>
(LAMP1, LAMP2)
Power standby
< > button
<MAIN POWER> switch
Attention
Panasonic shall not be responsible for damages
or malfunctioning of the product due to the use
of other than a Panasonic lamp unit. Use only
Do not use replacement lamp units (for portrait
mode) and normal lamp units together. Check
the product number on the label attached to the
replacement lamp unit.
A replacement lamp unit (for portrait mode) must
be used when installing in a portrait orientation.
Do not install the projector in any orientation other
than portrait when using a replacement lamp unit
(for portrait mode).
Since the luminous lamp is made of glass, it may
burst if dropped or hit with a hard object. Please
handle with care.
Do not disassemble or modify the lamp unit.
When replacing the lamp unit, be sure to hold it
by the handle because its surface is pointed and
its shape is protruded.
The lamp may be burst. Replace the lamp unit
carefully so that the broken pieces of the lamp
glass will not scatter.
The lamp contains mercury. When disposing of
used lamp units, contact your local authorities or
dealer for correct methods of disposal.
Panasonic recommends that the lamp unit be
replaced by a specialized engineer. Contact your
dealer.
Note
A Phillips screwdriver is necessary when
replacing the lamp unit.
The Multi Projector Monitoring & Control Software
in the CD-ROM supplied with the PT-DZ13K
series may not support the Model No. display of
the replacement lamp unit (for portrait mode).
Download the latest version of the software from
“Multi Projector Monitoring & Control Software” on
the Panasonic website (https://panasonic.net/cns/
projector/).
Switching off the projector
When the projector is operating, perform the follow-
ing steps to turn off the projector, and wait until the
lamp unit cools off then make the replacement.
1) Press the power standby < >
button.
2) Press ◀▶ to select [OK], and
press the <ENTER> button.
(Or press the power standby < >
button again.)
Projection of the image will stop, and the
power indicator <ON (G)/STANDBY (R)> on
the projector lights in orange.
(The fan keeps running.)
3) Wait until the power indicator
<ON (G)/STANDBY (R)> of the
projector lights in red (and the
fan stops) for approximately 170
seconds.
4) Press the <OFF>side of the <MAIN
POWER> switch to turn off the
power.
ET-LAD310A(W)_320P(W).indd 3 2013/03/22 11:15:15

4-ENGLISH
Replacing the lamp unit
Attention
zWhen the projector is mounted on the ceiling, do
not make the replacement while your face is near
the lamp unit.
zDo not remove or loosen the screws other than
specied ones when replacing the lamp unit.
zUse both lamp units of the same type.
1) Set the <MAIN POWER> switch to
<OFF> and disconnect the power
plug from the power outlet.
zWait at least one hour and check if the lamp
unit has cooled down.
2) Remove the lamp unit cover.
(i) Use a Phillips screwdriver to loosen the
lamp unit cover xing screw (one screw)
counterclockwise until it turns freely, and
then open the lamp unit cover slowly in
the direction of the arrow described in the
following gure.
• Opening the lamp unit cover quickly may
result in damage to the cover.
• If you loosen the lamp unit cover xing
screw with the projector installed upward
in the vertical direction, the lamp unit cover
may open on its weight and fall off.
(ii) Hold the lamp unit cover securely and slide
it in the direction of the arrow, and then pull
it out backward to remove.
• The lamp unit cover includes a fan and
other components so caution is necessary
when handling during replacement.
Lamp unit cover
fixing screw
Lamp unit cover
3) Remove the lamp unit.
zUse a Phillips screwdriver to turn the
lamp unit xing screws (two screws)
counterclockwise until they turn freely, and
then remove the lamp unit in the horizontal
direction while holding the handle.
zDo not remove the screws other than the
lamp unit xing screws.
Lamp unit 2 Lamp unit 1
Handles
Lamp unit fixing screws
4) Attach the lamp unit.
(i) Push in the new lamp unit while checking
the position of the attachment guide
grooves and the lamp unit attaching guide.
• If the lamp unit is not installed properly,
remove it and then gently install it again.
Pushing it in forcibly or exerting excessive
force may break the connector.
(ii) Use a Phillips screwdriver to tighten the
lamp unit xing screws (two screws each).
• Make sure to attach the lamp unit
properly.
Mounting guide grooves
Fan power
connector
Lamp unit
mounting
guide
Mounting guide grooves
5) Attach the lamp unit cover
zClose the lamp unit cover by the reverse
procedure from step 2), and use a Phillips
screwdriver to tighten the lamp unit cover
xing screw (one screw).
zMake sure the connector at the side of the
lamp unit cover is rmly inserted in the fan
power connector.
zMake sure to attach the lamp unit cover
properly.
Note
zWhen you place the new lamp unit, the projector
resets the total usage time of the lamp unit
automatically.
Attention
zAfter unpacking the lamp unit, discard the
packaging material properly.
ET-LAD310A(W)_320P(W).indd 4 2013/03/22 11:15:15

ENGLISH-5
Memo
ET-LAD310A(W)_320P(W).indd 5 2013/03/22 11:15:16

Panasonic Corporation
Web Site : https://panasonic.net/cns/projector/
SS0313KM1047 -KI
Printed in Japan
Information on Disposal for Users of Waste Electrical & Electronic Equipment (private households)
This symbol on the products and/or accompanying documents means that used electrical
and electronic products should not be mixed with general household waste.
For proper treatment, recovery and recycling, please take these products to designated
collection points,where they will be accepted on a free of charge basis.
Alternatively, in some countries you may be able to return your products to your local retailer
upon the purchase of an equivalent new product.
Disposing of this product correctly will help to save valuable resources and prevent any
potential negative effects on human health and the environment which could otherwise arise
from inappropriate waste handling. Please contact your local authority for further details of
your nearest designated collection point.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national
legislation.
For business users in the European Union
If you wish to discard electrical and electronic equipment, please contact your dealer or
supplier for further information.
Information on Disposal in other Countries outside the European Union
This symbol is only valid in the European Union.
If you wish to discard this product, please contact your local authorities or dealer and ask for
the correct method of disposal.
Information for users in the European Union
Importer’s name and address within the European Union
Panasonic Marketing Europe GmbH
Panasonic Testing Center
Winsbergring 15, 22525 Hamburg, Germany
ET-LAD310A(W)_320P(W).indd 6 2013/03/22 11:15:16